- Community Home
- >
- Servers and Operating Systems
- >
- Integrity Servers
- >
- Add and activate cell to Partition
Integrity Servers
1752226
Members
5524
Online
108785
Solutions
Forums
Categories
Company
Local Language
юдл
back
Forums
Discussions
Forums
- Data Protection and Retention
- Entry Storage Systems
- Legacy
- Midrange and Enterprise Storage
- Storage Networking
- HPE Nimble Storage
Discussions
Discussions
Discussions
Forums
Forums
Discussions
юдл
back
Discussion Boards
Discussion Boards
Discussion Boards
Discussion Boards
- BladeSystem Infrastructure and Application Solutions
- Appliance Servers
- Alpha Servers
- BackOffice Products
- Internet Products
- HPE 9000 and HPE e3000 Servers
- Networking
- Netservers
- Secure OS Software for Linux
- Server Management (Insight Manager 7)
- Windows Server 2003
- Operating System - Tru64 Unix
- ProLiant Deployment and Provisioning
- Linux-Based Community / Regional
- Microsoft System Center Integration
Discussion Boards
Discussion Boards
Discussion Boards
Discussion Boards
Discussion Boards
Discussion Boards
Discussion Boards
Discussion Boards
Discussion Boards
Discussion Boards
Discussion Boards
Discussion Boards
Discussion Boards
Discussion Boards
Discussion Boards
Discussion Boards
Discussion Boards
Discussion Boards
Discussion Boards
Discussion Boards
Discussion Boards
Discussion Boards
Blogs
Information
Community
Resources
Community Language
Language
Forums
Blogs
Go to solution
Topic Options
- Subscribe to RSS Feed
- Mark Topic as New
- Mark Topic as Read
- Float this Topic for Current User
- Bookmark
- Subscribe
- Printer Friendly Page
- Mark as New
- Bookmark
- Subscribe
- Mute
- Subscribe to RSS Feed
- Permalink
- Report Inappropriate Content
тАО07-30-2007 12:09 AM
тАО07-30-2007 12:09 AM
hi sirs,
i need help to add and activate all my cell installed on rx7620 integrity server,
HP-UX 11.23 has been installed on the server
[mp] MP:CM> cp
--------+--+
Cabinet |0 |
--------+--+
Slot |01|
--------+--+
Part 0 |.*|
[mp] MP:CM> du
The following MP bus devices were found:
+---+----+----+-----+-----+-------+-----+
| | | | | | | |
| | |LAN\| Sys | | IO | |
|Cab| MP |SCSI|Bkpln|Cells|Chassis| BPS |
| # |M S|0 1| | 0 1 | 0 1 | 0 1 |
+---+----+----+-----+-----+-------+-----+
| 0 |* *| *| * | * * | * * | * * |
+---+----+----+-----+-----+-------+-----+
i tryed this command:
parmodify -p0 -a0:base:y:ri
and then shutdown -R then i got an error:
EFI version 1.10 [14.61] Running on GenuineIntel Itanium(R) 2 Processor
EFI server rx7620 SAL [14:34:57] - HP
Loading 'ULTRA160_SCSI'...
driver: Image ULTRA160_SCSI loaded at 40FD5BE000-40FD5FE000. Returned Success
Loading 'BRM5701_LAN'...
Copyright (c) 2000-2005 Broadcom Corporation
Broadcom NetXtreme Gigabit Ethernet EFI driver v7.0.10
driver: Image BRM5701_LAN loaded at 40FD644000-40FD67E000. Returned Success
Loading 'FPSWA'...
driver: Image FPSWA loaded at 40FD554000-40FD5BE000. Returned Success
POSSE Library is loading...
EFI Shell version 1.10 [14.61]
Device mapping table
acpiconfig: Warning, the current ACPI configuration mode
does not match across the cells.
Please use the 'acpiconfig' command to set the desired
ACPI configuration mode, then issue a global cold reset.
i re-genesis the partition
MP>cm
CM>cc
and i saved the HPux 11.23 installed on the disk with the old configuration.
Thank you in advanced
i need help to add and activate all my cell installed on rx7620 integrity server,
HP-UX 11.23 has been installed on the server
[mp] MP:CM> cp
--------+--+
Cabinet |0 |
--------+--+
Slot |01|
--------+--+
Part 0 |.*|
[mp] MP:CM> du
The following MP bus devices were found:
+---+----+----+-----+-----+-------+-----+
| | | | | | | |
| | |LAN\| Sys | | IO | |
|Cab| MP |SCSI|Bkpln|Cells|Chassis| BPS |
| # |M S|0 1| | 0 1 | 0 1 | 0 1 |
+---+----+----+-----+-----+-------+-----+
| 0 |* *| *| * | * * | * * | * * |
+---+----+----+-----+-----+-------+-----+
i tryed this command:
parmodify -p0 -a0:base:y:ri
and then shutdown -R then i got an error:
EFI version 1.10 [14.61] Running on GenuineIntel Itanium(R) 2 Processor
EFI server rx7620 SAL [14:34:57] - HP
Loading 'ULTRA160_SCSI'...
driver: Image ULTRA160_SCSI loaded at 40FD5BE000-40FD5FE000. Returned Success
Loading 'BRM5701_LAN'...
Copyright (c) 2000-2005 Broadcom Corporation
Broadcom NetXtreme Gigabit Ethernet EFI driver v7.0.10
driver: Image BRM5701_LAN loaded at 40FD644000-40FD67E000. Returned Success
Loading 'FPSWA'...
driver: Image FPSWA loaded at 40FD554000-40FD5BE000. Returned Success
POSSE Library is loading...
EFI Shell version 1.10 [14.61]
Device mapping table
acpiconfig: Warning, the current ACPI configuration mode
does not match across the cells.
Please use the 'acpiconfig' command to set the desired
ACPI configuration mode, then issue a global cold reset.
i re-genesis the partition
MP>cm
CM>cc
and i saved the HPux 11.23 installed on the disk with the old configuration.
Thank you in advanced
Solved! Go to Solution.
3 REPLIES 3
- Mark as New
- Bookmark
- Subscribe
- Mute
- Subscribe to RSS Feed
- Permalink
- Report Inappropriate Content
тАО07-30-2007 12:39 AM
тАО07-30-2007 12:39 AM
Solution
Issue a "acpiconfig default" from EFI.
Boot up the server and run "parmgr" to assign the cell.
You can also go to the SMH
your_server:2301/parmgr
to do this.
Hope this helps!
Regards
Torsten.
__________________________________________________
There are only 10 types of people in the world -
those who understand binary, and those who don't.
__________________________________________________
No support by private messages. Please ask the forum!
If you feel this was helpful please click the KUDOS! thumb below!
Boot up the server and run "parmgr" to assign the cell.
You can also go to the SMH
your_server:2301/parmgr
to do this.
Hope this helps!
Regards
Torsten.
__________________________________________________
There are only 10 types of people in the world -
those who understand binary, and those who don't.
__________________________________________________
No support by private messages. Please ask the forum!
If you feel this was helpful please click the KUDOS! thumb below!
- Mark as New
- Bookmark
- Subscribe
- Mute
- Subscribe to RSS Feed
- Permalink
- Report Inappropriate Content
тАО07-30-2007 08:20 AM
тАО07-30-2007 08:20 AM
Re: Add and activate cell to Partition
done
thank you
thank you
- Mark as New
- Bookmark
- Subscribe
- Mute
- Subscribe to RSS Feed
- Permalink
- Report Inappropriate Content
тАО07-30-2007 05:20 PM
тАО07-30-2007 05:20 PM
Re: Add and activate cell to Partition
Please read this too:
http://forums1.itrc.hp.com/service/forums/helptips.do?#33
Hope this helps!
Regards
Torsten.
__________________________________________________
There are only 10 types of people in the world -
those who understand binary, and those who don't.
__________________________________________________
No support by private messages. Please ask the forum!
If you feel this was helpful please click the KUDOS! thumb below!
http://forums1.itrc.hp.com/service/forums/helptips.do?#33
Hope this helps!
Regards
Torsten.
__________________________________________________
There are only 10 types of people in the world -
those who understand binary, and those who don't.
__________________________________________________
No support by private messages. Please ask the forum!
If you feel this was helpful please click the KUDOS! thumb below!
The opinions expressed above are the personal opinions of the authors, not of Hewlett Packard Enterprise. By using this site, you accept the Terms of Use and Rules of Participation.
News and Events
Support
© Copyright 2024 Hewlett Packard Enterprise Development LP