- Community Home
- >
- Servers and Operating Systems
- >
- Integrity Servers
- >
- BL 870C OS Load can't access HDD
Integrity Servers
1753844
Members
7790
Online
108806
Solutions
Forums
Categories
Company
Local Language
back
Forums
Discussions
Forums
- Data Protection and Retention
- Entry Storage Systems
- Legacy
- Midrange and Enterprise Storage
- Storage Networking
- HPE Nimble Storage
Discussions
Discussions
Discussions
Forums
Discussions
back
Discussion Boards
Discussion Boards
Discussion Boards
Discussion Boards
- BladeSystem Infrastructure and Application Solutions
- Appliance Servers
- Alpha Servers
- BackOffice Products
- Internet Products
- HPE 9000 and HPE e3000 Servers
- Networking
- Netservers
- Secure OS Software for Linux
- Server Management (Insight Manager 7)
- Windows Server 2003
- Operating System - Tru64 Unix
- ProLiant Deployment and Provisioning
- Linux-Based Community / Regional
- Microsoft System Center Integration
Discussion Boards
Discussion Boards
Discussion Boards
Discussion Boards
Discussion Boards
Discussion Boards
Discussion Boards
Discussion Boards
Discussion Boards
Discussion Boards
Discussion Boards
Discussion Boards
Discussion Boards
Discussion Boards
Discussion Boards
Discussion Boards
Discussion Boards
Discussion Boards
Discussion Boards
Blogs
Information
Community
Resources
Community Language
Language
Forums
Blogs
Topic Options
- Subscribe to RSS Feed
- Mark Topic as New
- Mark Topic as Read
- Float this Topic for Current User
- Bookmark
- Subscribe
- Printer Friendly Page
- Mark as New
- Bookmark
- Subscribe
- Mute
- Subscribe to RSS Feed
- Permalink
- Report Inappropriate Content
04-14-2009 10:32 AM
04-14-2009 10:32 AM
BL 870C OS Load can't access HDD
I have a a semi new install of one Hp BL 870C.
The issue I am having that that the OS (W2K3) can't gain access to the HDD's after using the easy-setup app on the Smart startr (rev 6.20) CD.
Any help would be appreciated.
The issue I am having that that the OS (W2K3) can't gain access to the HDD's after using the easy-setup app on the Smart startr (rev 6.20) CD.
Any help would be appreciated.
1 REPLY 1
- Mark as New
- Bookmark
- Subscribe
- Mute
- Subscribe to RSS Feed
- Permalink
- Report Inappropriate Content
04-14-2009 10:30 PM
04-14-2009 10:30 PM
Re: BL 870C OS Load can't access HDD
Scott,
make sure you configured the internal SAS drives first in raid1 (IM Integrated Mirror) because W2K3 does not recognize the SAS disks and needs to see a emulation of a SCSI device which is exactly what the RAID1 mirror does.
Use the command drvcfg at EFI shell to configure the raid controller (note this is not a SmartArray).
If all of the above is correct and you still face this issue, then check if you have a W2K3 with SP2 included ?(slipstreamed) because that is a minimum requirement.
Als check the documentation available on your SmartSetup V6.2 cd , i attached an older version which shows the screens when you configure the raid (on a BL860C but it is the same basically ) via the SmartSetup cd and not from the EFI shell (using drvcfg)
HTH
Kris
make sure you configured the internal SAS drives first in raid1 (IM Integrated Mirror) because W2K3 does not recognize the SAS disks and needs to see a emulation of a SCSI device which is exactly what the RAID1 mirror does.
Use the command drvcfg at EFI shell to configure the raid controller (note this is not a SmartArray).
If all of the above is correct and you still face this issue, then check if you have a W2K3 with SP2 included ?(slipstreamed) because that is a minimum requirement.
Als check the documentation available on your SmartSetup V6.2 cd , i attached an older version which shows the screens when you configure the raid (on a BL860C but it is the same basically ) via the SmartSetup cd and not from the EFI shell (using drvcfg)
HTH
Kris
The opinions expressed above are the personal opinions of the authors, not of Hewlett Packard Enterprise. By using this site, you accept the Terms of Use and Rules of Participation.
News and Events
Support
© Copyright 2024 Hewlett Packard Enterprise Development LP