- Community Home
- >
- Servers and Operating Systems
- >
- Integrity Servers
- >
- Re: CISS Smart array controller error.
Categories
Company
Local Language
Forums
Discussions
Forums
- Data Protection and Retention
- Entry Storage Systems
- Legacy
- Midrange and Enterprise Storage
- Storage Networking
- HPE Nimble Storage
Discussions
Discussions
Discussions
Forums
Forums
Discussions
Discussion Boards
Discussion Boards
Discussion Boards
Discussion Boards
- BladeSystem Infrastructure and Application Solutions
- Appliance Servers
- Alpha Servers
- BackOffice Products
- Internet Products
- HPE 9000 and HPE e3000 Servers
- Networking
- Netservers
- Secure OS Software for Linux
- Server Management (Insight Manager 7)
- Windows Server 2003
- Operating System - Tru64 Unix
- ProLiant Deployment and Provisioning
- Linux-Based Community / Regional
- Microsoft System Center Integration
Discussion Boards
Discussion Boards
Discussion Boards
Discussion Boards
Discussion Boards
Discussion Boards
Discussion Boards
Discussion Boards
Discussion Boards
Discussion Boards
Discussion Boards
Discussion Boards
Discussion Boards
Discussion Boards
Discussion Boards
Discussion Boards
Discussion Boards
Discussion Boards
Discussion Boards
Discussion Boards
Discussion Boards
Discussion Boards
Community
Resources
Forums
Blogs
- Subscribe to RSS Feed
- Mark Topic as New
- Mark Topic as Read
- Float this Topic for Current User
- Bookmark
- Subscribe
- Printer Friendly Page
- Mark as New
- Bookmark
- Subscribe
- Mute
- Subscribe to RSS Feed
- Permalink
- Report Inappropriate Content
тАО10-27-2009 10:10 PM
тАО10-27-2009 10:10 PM
CISS Smart array controller error.
========================================
CISS: Raid SA controller on hardware part 0/1/1/0/4/0 has detected fetal IO.
logical block add -0
Logical block count 16
Logical command 0x20
Fetal Drive Bus 1
Fetal Drive ID 0
==========================================
I have two hard disk when I boot with "boot -lm" ( LVM maintenance) I am able to go to single user mode and able to activate all the VG and mount LV's. After mounting all partition I tried to execute below commands but I got same error and not getting prompt back.
===========================
sautil /dev/ciss2
saconfig /dev/ciss2 -F off
================================
I am having data on this disk so I don't want to take risk by clearing SA configurations please help. How to resolve this?
- Mark as New
- Bookmark
- Subscribe
- Mute
- Subscribe to RSS Feed
- Permalink
- Report Inappropriate Content
тАО10-27-2009 10:15 PM
тАО10-27-2009 10:15 PM
Re: CISS Smart array controller error.
Can you access ORCA (press ESC followed by 8 during boot) and check the status from there?
Hope this helps!
Regards
Torsten.
__________________________________________________
There are only 10 types of people in the world -
those who understand binary, and those who don't.
__________________________________________________
No support by private messages. Please ask the forum!
If you feel this was helpful please click the KUDOS! thumb below!
- Mark as New
- Bookmark
- Subscribe
- Mute
- Subscribe to RSS Feed
- Permalink
- Report Inappropriate Content
тАО10-28-2009 01:11 AM
тАО10-28-2009 01:11 AM
Re: CISS Smart array controller error.
- Mark as New
- Bookmark
- Subscribe
- Mute
- Subscribe to RSS Feed
- Permalink
- Report Inappropriate Content
тАО10-28-2009 01:15 AM
тАО10-28-2009 01:15 AM
Re: CISS Smart array controller error.
- Mark as New
- Bookmark
- Subscribe
- Mute
- Subscribe to RSS Feed
- Permalink
- Report Inappropriate Content
тАО10-28-2009 08:47 AM
тАО10-28-2009 08:47 AM
Re: CISS Smart array controller error.
I would try to power off the server, remove this disk and power on again. Ignore the message regarding a missing drive, the server should start. If not successful, power off again and try the other drive.
Hope this helps!
Regards
Torsten.
__________________________________________________
There are only 10 types of people in the world -
those who understand binary, and those who don't.
__________________________________________________
No support by private messages. Please ask the forum!
If you feel this was helpful please click the KUDOS! thumb below!
- Mark as New
- Bookmark
- Subscribe
- Mute
- Subscribe to RSS Feed
- Permalink
- Report Inappropriate Content
тАО11-01-2009 10:51 PM
тАО11-01-2009 10:51 PM
Re: CISS Smart array controller error.
a.) I booted system in LVM maintenance (boot -lm) mode and ran command "setboot -p /dev/disk/disk3 -b on" -- Disk which is having SCSI ID 0(lower disk )
b.) No alternate boot path set
c.) Edited /etc/lvmrc to activate only /dev/vg00
d.) rebooted the system by removing one hard disk i.e SCSI ID 1. But I am getting error "boot disk failure"..
- Mark as New
- Bookmark
- Subscribe
- Mute
- Subscribe to RSS Feed
- Permalink
- Report Inappropriate Content
тАО11-01-2009 11:03 PM
тАО11-01-2009 11:03 PM
Re: CISS Smart array controller error.
Is it?
Hope this helps!
Regards
Torsten.
__________________________________________________
There are only 10 types of people in the world -
those who understand binary, and those who don't.
__________________________________________________
No support by private messages. Please ask the forum!
If you feel this was helpful please click the KUDOS! thumb below!
- Mark as New
- Bookmark
- Subscribe
- Mute
- Subscribe to RSS Feed
- Permalink
- Report Inappropriate Content
тАО11-02-2009 03:45 AM
тАО11-02-2009 03:45 AM
Re: CISS Smart array controller error.
But my doubt is if it is a problem with Array controller why it is booting in "boot -lm" . And I am able to mount all the disks there. If I am booting system normally this error is coming.. !!
- Mark as New
- Bookmark
- Subscribe
- Mute
- Subscribe to RSS Feed
- Permalink
- Report Inappropriate Content
тАО11-02-2009 05:22 AM
тАО11-02-2009 05:22 AM
Re: CISS Smart array controller error.
What firmware is on the controller (you see this during boot)?
HP Smart Array 6400-128 Controller (version 2.84) 1 Logical Drive
Press
Hope this helps!
Regards
Torsten.
__________________________________________________
There are only 10 types of people in the world -
those who understand binary, and those who don't.
__________________________________________________
No support by private messages. Please ask the forum!
If you feel this was helpful please click the KUDOS! thumb below!
- Mark as New
- Bookmark
- Subscribe
- Mute
- Subscribe to RSS Feed
- Permalink
- Report Inappropriate Content
тАО11-03-2009 03:58 AM
тАО11-03-2009 03:58 AM
Re: CISS Smart array controller error.
And Smart Array controller is 6400-128 (version 2.34)