- Community Home
- >
- Servers and Operating Systems
- >
- Integrity Servers
- >
- Error when adding a cell to a SD64
Categories
Company
Local Language
Forums
Discussions
Forums
- Data Protection and Retention
- Entry Storage Systems
- Legacy
- Midrange and Enterprise Storage
- Storage Networking
- HPE Nimble Storage
Discussions
Discussions
Discussions
Forums
Forums
Discussions
Discussion Boards
Discussion Boards
Discussion Boards
Discussion Boards
- BladeSystem Infrastructure and Application Solutions
- Appliance Servers
- Alpha Servers
- BackOffice Products
- Internet Products
- HPE 9000 and HPE e3000 Servers
- Networking
- Netservers
- Secure OS Software for Linux
- Server Management (Insight Manager 7)
- Windows Server 2003
- Operating System - Tru64 Unix
- ProLiant Deployment and Provisioning
- Linux-Based Community / Regional
- Microsoft System Center Integration
Discussion Boards
Discussion Boards
Discussion Boards
Discussion Boards
Discussion Boards
Discussion Boards
Discussion Boards
Discussion Boards
Discussion Boards
Discussion Boards
Discussion Boards
Discussion Boards
Discussion Boards
Discussion Boards
Discussion Boards
Discussion Boards
Discussion Boards
Discussion Boards
Discussion Boards
Discussion Boards
Discussion Boards
Discussion Boards
Community
Resources
Forums
Blogs
- Subscribe to RSS Feed
- Mark Topic as New
- Mark Topic as Read
- Float this Topic for Current User
- Bookmark
- Subscribe
- Printer Friendly Page
- Mark as New
- Bookmark
- Subscribe
- Mute
- Subscribe to RSS Feed
- Permalink
- Report Inappropriate Content
тАО03-02-2009 07:53 AM
тАО03-02-2009 07:53 AM
When adding a new cell to a npar, i am getting these errors.
On the console:
Validating fPars configuration ... Complete
Complete
Verifying sram malloc sanity ... Complete
Verifying registry sanity ... Complete
Verifying device tree sanity ... Complete
Verifying ACPI configuration consistency ... Complete
Verifying partitioning mode consistency ... ERROR
Verifying IO configuration consistency ... Complete
Firmware detected a configuration mismatch. The partition will be reset.
on the system event log from the mp:
47815 SFW 0,6,0 2 43801cdd60e01a0d 000000000000000d FPARS_MODE_MISMATCH
47815 03/02/2009 15:26:40
47814 PDHC 1,5 2 54800b5a0de01a0b ffffffffff0f000c RESET_CELL
47814 03/02/2009 15:23:30
and the firmware versions are the same:
0, 6 | 009.022.000 i | 005.024.000 i | 023.003.040 | 023.003.030 |
1, 5 | 009.022.000 i | 009.022.000 i | 023.003.040 | 023.003.040 |
Any idea ?
Solved! Go to Solution.
- Mark as New
- Bookmark
- Subscribe
- Mute
- Subscribe to RSS Feed
- Permalink
- Report Inappropriate Content
тАО03-02-2009 08:40 AM
тАО03-02-2009 08:40 AM
Re: Error when adding a cell to a SD64
Does HP done the scan test, cpudiag when they put the cell? Maybe it could help to show what's happening with this issue.
- Mark as New
- Bookmark
- Subscribe
- Mute
- Subscribe to RSS Feed
- Permalink
- Report Inappropriate Content
тАО03-02-2009 11:38 AM
тАО03-02-2009 11:38 AM
SolutionHope this helps!
Regards
Torsten.
__________________________________________________
There are only 10 types of people in the world -
those who understand binary, and those who don't.
__________________________________________________
No support by private messages. Please ask the forum!
If you feel this was helpful please click the KUDOS! thumb below!
- Mark as New
- Bookmark
- Subscribe
- Mute
- Subscribe to RSS Feed
- Permalink
- Report Inappropriate Content
тАО03-03-2009 12:48 AM
тАО03-03-2009 12:48 AM
Re: Error when adding a cell to a SD64
Looking at the above output of your firmware versions, it would appear that they are NOT the same IFP SYS FW.
Look carefully.
Regards,
Phil
- Mark as New
- Bookmark
- Subscribe
- Mute
- Subscribe to RSS Feed
- Permalink
- Report Inappropriate Content
тАО03-03-2009 12:48 AM
тАО03-03-2009 12:48 AM
Re: Error when adding a cell to a SD64
This npar has vpars, and I needed after shutdown -R -H from the vpars, a full boot in npars mode, I only has done it up to de efi.
Everything working fine now
- Mark as New
- Bookmark
- Subscribe
- Mute
- Subscribe to RSS Feed
- Permalink
- Report Inappropriate Content
тАО03-03-2009 12:49 AM
тАО03-03-2009 12:49 AM
Re: Error when adding a cell to a SD64
- Mark as New
- Bookmark
- Subscribe
- Mute
- Subscribe to RSS Feed
- Permalink
- Report Inappropriate Content
тАО03-03-2009 02:19 AM
тАО03-03-2009 02:19 AM
Re: Error when adding a cell to a SD64
The vPars manual says, you need to do a full boot into nPars mode, because the kernel will write the new information.
Regarding the firmware:
The active versions are the same - this is enough.
There is already a newer version with IPF FW 009.048.000, BTW.
Hope this helps!
Regards
Torsten.
__________________________________________________
There are only 10 types of people in the world -
those who understand binary, and those who don't.
__________________________________________________
No support by private messages. Please ask the forum!
If you feel this was helpful please click the KUDOS! thumb below!