Integrity Servers
1752795 Members
6026 Online
108789 Solutions
New Discussion

Re: HP Integrity RX2660 Boot Problem

 
chocoteco
Occasional Visitor

HP Integrity RX2660 Boot Problem

The rx2660 server doesnt have signal video. 

 

The status leds are the next:

 

Power LED : Steady green

External health LED : Steady green

Internal health LED : Steady green

System health LED  : Blink between red and amber. one minute blinks red and the next blinks amber

 

 

 

7 REPLIES 7
S_Logan
HPE Pro

Re: HP Integrity RX2660 Boot Problem

Hi,

 

Please acknowledge and view  the MP SL and FPL Logs.

 

You Can switch to the  MP console by pressing CTRL+B , then login to MP  and  view the logs from MP:CM> prompt

I work for HPE

Accept or Kudo


[Any personal opinions expressed are mine, and not official statements on behalf of Hewlett Packard Enterprise]
S_Logan
HPE Pro

Re: HP Integrity RX2660 Boot Problem

Hi,

 

You can capture the SL logs and update here.

 

Let us look in to that

I work for HPE

Accept or Kudo


[Any personal opinions expressed are mine, and not official statements on behalf of Hewlett Packard Enterprise]
S_Logan
HPE Pro

Re: HP Integrity RX2660 Boot Problem

Hi 

 

Please find the LED Status as updated:

 

Power LED = Green: full power is ON
System health LED = Flashing amber: warning / Flashing red: system fault
Internal health LED = Green: system health is good
External health LED = Green: system health is good

I work for HPE

Accept or Kudo


[Any personal opinions expressed are mine, and not official statements on behalf of Hewlett Packard Enterprise]
chocoteco
Occasional Visitor

Re: HP Integrity RX2660 Boot Problem

I am not be able to see nothing in the monitor... No signal video and not signal in the VGA port (console output).  

It has been tried with two different monitors. 

 

iLO 2 MP LAN heartbeat 

Standby power LED 

BMC heartbeat   are blinking normally. 

S_Logan
HPE Pro

Re: HP Integrity RX2660 Boot Problem

Hi 

 

Hope the display configured to VGA port. Normally it should be connected to Serial console to view the MP Logs.

 

If you power recycle , are able to see few startup screens?

I work for HPE

Accept or Kudo


[Any personal opinions expressed are mine, and not official statements on behalf of Hewlett Packard Enterprise]
S_Logan
HPE Pro

Re: HP Integrity RX2660 Boot Problem

Hi, 

i understand the console out put connected to VGA, in this case you wont be seeing the progress happening after some time, even you can see the mesaage console configure to serial then the cursor will be blinking continously.

 

 

Please confirm , is this happening in your case. if so , we need to configure  the console to re direct the output to VGA.

I work for HPE

Accept or Kudo


[Any personal opinions expressed are mine, and not official statements on behalf of Hewlett Packard Enterprise]
S_Logan
HPE Pro

Re: HP Integrity RX2660 Boot Problem

Hi,

 

If Console configuration needed, please refer the following links:

 


HP Integrity rx2660, rx3600, and rx6600 Servers - How Is Console Output Configured?
http://h20565.www2.hp.com/hpsc/doc/public/display?sp4ts.oid=3346452&docId=emr_na-c01479528&docLocale=en_US

 

 

HP Integrity rx2660 Servers - Configuring the iLO 2 MP LAN Using the RS-232 Serial Port
http://h20564.www2.hp.com/hpsc/doc/public/display?docId=emr_na-c02250882

I work for HPE

Accept or Kudo


[Any personal opinions expressed are mine, and not official statements on behalf of Hewlett Packard Enterprise]