Integrity Servers
cancel
Showing results for 
Search instead for 
Did you mean: 

How to add an option to boot profile?

 
dictum9
Super Advisor

How to add an option to boot profile?


reconnect -r


Broadcom NetXtreme Gigabit Ethernet (BCM5703) is detected (PCI-X)
Scsi(Pun2,Lun0) _NEC DVD_RW ND-3540A 1.30 ( 40 MBytes/sec)
Scsi(Pun5,Lun0) HP Ultrium 3-SCSI G54D ( 80 MBytes/sec)
HP 2Port 2Gb Fibre Channel Adapter (driver 1.47, firmware 3.03.154)
Broadcom NetXtreme Gigabit Ethernet (BCM5703) is detected (PCI-X)
HP 2Port 2Gb Fibre Channel Adapter (driver 1.47, firmware 3.03.154)
Broadcom NetXtreme Gigabit Ethernet (BCM5703) is detected (PCI-X)
ReconnectController(0,0,0) : Status = Success

Shell> bcfg boot dump
The boot option list is:
01. Acpi(HWP0002,PNP0A03,C)/Pci(1|0)/Pci(4|0)/Fibre(WWN500143801136F009,Lun4001000000000000)/HD(Part1,Sig5923D410-66FB-11E5-
8000-D6217B60E588)/\EFI\HPUX\HPUX.EFI "HP-UX Primary Boot: 0/0/12/1/0/4/0.0x500143801136f009.0x4001000000000000"
02. Acpi(HWP0002,PNP0A03,E)/Pci(1|0)/Pci(4|0)/Fibre(WWN50001FE1500940AD,Lun4001000000000000)/HD(Part1,Sig2A0D3110-EF8C-11DC-
8002-D6217B60E588)/\EFI\HPUX\HPUX.EFI "HP-UX Alternate Boot: 0/0/14/1/0/4/0.1.2.0.0.0.1"
03. Acpi(HWP0002,PNP0A03,0)/Pci(1|0)/Mac(0018FE2884C3) "SYS LAN 0 Cabinet 0 [Acpi(HWP0002,PNP0A03,0)/Pci(1|0)/Mac(0018FE2884
C3)]"
04. Acpi(HWP0002,PNP0A03,100)/Pci(1|0)/Mac(0018FE2884BF) "SYS LAN 1 Cabinet 0 [Acpi(HWP0002,PNP0A03,100)/Pci(1|0)/Mac(0018FE
2884BF)]"
05. VenHw(D65A6B8C-71E5-4DF0-A909-F0D2992B5AA9) "EFI Shell [Built-in]"
06. Acpi(HWP0002,PNP0A03,100)/Pci(2|1)/Scsi(Pun2,Lun0) "Lower DVD" OPT
07. Acpi(HWP0002,PNP0A03,100)/Pci(2|1)/Scsi(Pun2,Lun0) "Upper DVD" OPT
08. Acpi(HWP0002,PNP0A03,0)/Pci(3|1)/Scsi(Pun5,Lun0) "edwboot"
Shell> i(HWP0002,PNP0A03,10E)/Pci(1|0)/Pci(4|0)/Fibre(WWN500143801136F00C,Lun4002000000000000)/HD(Part1,Sig425F5CB8-774E-11E
1-8000-D6217B60E588)/\EFI\HPUX\HPUX.EFI "HP-UX HA Alternate Boot: 1/0/14/1/0/4/0.0x500143801136f00c.0x4002000000000000"
0A. Acpi(HWP0002,PNP0A03,0)/Pci(3|1)/Scsi(Pun5,Lun0) "edwbootoptinon"
0B. Acpi(HWP0002,PNP0A03,0)/Pci(2|1)/Scsi(Pun2,Lun0) "boot" OPT

 

  dbprofile lists a  few network boot options but I need to boot off the tape (0A or Scsi(Pun5,Lun0) HP Ultrium 3-SCSI G54D ( 80 MBytes/sec) above. 

 

1 REPLY 1
Robert_Jewell
Honored Contributor

Re: How to add an option to boot profile?

This document explains what you need to do:

http://h20564.www2.hpe.com/hpsc/doc/public/display?docId=emr_na-c01047087&sp4ts.oid=51400

(basically just add the tape drive device as a boot option using the boot config menus).

 

-Bob

----------------
Was this helpful? Like this post by giving me a thumbs up below!