- Community Home
- >
- Servers and Operating Systems
- >
- Integrity Servers
- >
- How to configure the 6402 controller before instal...
Integrity Servers
1752305
Members
4571
Online
108786
Solutions
Forums
Categories
Company
Local Language
юдл
back
Forums
Discussions
Forums
- Data Protection and Retention
- Entry Storage Systems
- Legacy
- Midrange and Enterprise Storage
- Storage Networking
- HPE Nimble Storage
Discussions
Discussions
Discussions
Forums
Forums
Discussions
юдл
back
Discussion Boards
Discussion Boards
Discussion Boards
Discussion Boards
- BladeSystem Infrastructure and Application Solutions
- Appliance Servers
- Alpha Servers
- BackOffice Products
- Internet Products
- HPE 9000 and HPE e3000 Servers
- Networking
- Netservers
- Secure OS Software for Linux
- Server Management (Insight Manager 7)
- Windows Server 2003
- Operating System - Tru64 Unix
- ProLiant Deployment and Provisioning
- Linux-Based Community / Regional
- Microsoft System Center Integration
Discussion Boards
Discussion Boards
Discussion Boards
Discussion Boards
Discussion Boards
Discussion Boards
Discussion Boards
Discussion Boards
Discussion Boards
Discussion Boards
Discussion Boards
Discussion Boards
Discussion Boards
Discussion Boards
Discussion Boards
Discussion Boards
Discussion Boards
Discussion Boards
Discussion Boards
Discussion Boards
Discussion Boards
Discussion Boards
Blogs
Information
Community
Resources
Community Language
Language
Forums
Blogs
Topic Options
- Subscribe to RSS Feed
- Mark Topic as New
- Mark Topic as Read
- Float this Topic for Current User
- Bookmark
- Subscribe
- Printer Friendly Page
- Mark as New
- Bookmark
- Subscribe
- Mute
- Subscribe to RSS Feed
- Permalink
- Report Inappropriate Content
тАО08-07-2005 02:49 PM
тАО08-07-2005 02:49 PM
How to configure the 6402 controller before installation Linux AS3.0
I will install Linux AS3.0 on rx2620 with controller 6402. The problem is coming, how to configure to RAID before install OS. I have try to press F8 when the machine boot up. But no response!!!!
Please help !!
Please help !!
Benny
3 REPLIES 3
- Mark as New
- Bookmark
- Subscribe
- Mute
- Subscribe to RSS Feed
- Permalink
- Report Inappropriate Content
тАО08-07-2005 06:45 PM
тАО08-07-2005 06:45 PM
Re: How to configure the 6402 controller before installation Linux AS3.0
Benny,
F8 is typical Pentium based server key. For Itanium server you have to enter into EFI environment.
After power up, you can see on console variuos EFI messages, pressing Enter you can issue username and password, then you type commands.
Antonio Vigliotti
F8 is typical Pentium based server key. For Itanium server you have to enter into EFI environment.
After power up, you can see on console variuos EFI messages, pressing Enter you can issue username and password, then you type commands.
Antonio Vigliotti
Antonio Maria Vigliotti
- Mark as New
- Bookmark
- Subscribe
- Mute
- Subscribe to RSS Feed
- Permalink
- Report Inappropriate Content
тАО08-07-2005 07:10 PM
тАО08-07-2005 07:10 PM
Re: How to configure the 6402 controller before installation Linux AS3.0
Since, I can press F8 to enter Smart Array Utilites, but it cannot see internal hard drives, please advice how to perfroms a bus scan and intitiates the rebuild???
Thanks!
Benny
Thanks!
Benny
Benny
- Mark as New
- Bookmark
- Subscribe
- Mute
- Subscribe to RSS Feed
- Permalink
- Report Inappropriate Content
тАО08-07-2005 09:09 PM
тАО08-07-2005 09:09 PM
Re: How to configure the 6402 controller before installation Linux AS3.0
Benny,
try posting here
http://forums1.itrc.hp.com/service/forums/familyhome.do?familyId=120
Antonio Vigliotti
try posting here
http://forums1.itrc.hp.com/service/forums/familyhome.do?familyId=120
Antonio Vigliotti
Antonio Maria Vigliotti
The opinions expressed above are the personal opinions of the authors, not of Hewlett Packard Enterprise. By using this site, you accept the Terms of Use and Rules of Participation.
News and Events
Support
© Copyright 2024 Hewlett Packard Enterprise Development LP