- Community Home
- >
- Servers and Operating Systems
- >
- Integrity Servers
- >
- Re: MP Console not responding
Categories
Company
Local Language
Forums
Discussions
Forums
- Data Protection and Retention
- Entry Storage Systems
- Legacy
- Midrange and Enterprise Storage
- Storage Networking
- HPE Nimble Storage
Discussions
Discussions
Discussions
Forums
Forums
Discussions
Discussion Boards
Discussion Boards
Discussion Boards
Discussion Boards
- BladeSystem Infrastructure and Application Solutions
- Appliance Servers
- Alpha Servers
- BackOffice Products
- Internet Products
- HPE 9000 and HPE e3000 Servers
- Networking
- Netservers
- Secure OS Software for Linux
- Server Management (Insight Manager 7)
- Windows Server 2003
- Operating System - Tru64 Unix
- ProLiant Deployment and Provisioning
- Linux-Based Community / Regional
- Microsoft System Center Integration
Discussion Boards
Discussion Boards
Discussion Boards
Discussion Boards
Discussion Boards
Discussion Boards
Discussion Boards
Discussion Boards
Discussion Boards
Discussion Boards
Discussion Boards
Discussion Boards
Discussion Boards
Discussion Boards
Discussion Boards
Discussion Boards
Discussion Boards
Discussion Boards
Discussion Boards
Discussion Boards
Discussion Boards
Discussion Boards
Community
Resources
Forums
Blogs
- Subscribe to RSS Feed
- Mark Topic as New
- Mark Topic as Read
- Float this Topic for Current User
- Bookmark
- Subscribe
- Printer Friendly Page
- Mark as New
- Bookmark
- Subscribe
- Mute
- Subscribe to RSS Feed
- Permalink
- Report Inappropriate Content
тАО10-12-2008 07:41 PM
тАО10-12-2008 07:41 PM
I have HP Itanium rx2620 with OS 11.23.
I can not use console display from the MP. It looks like session is hung.
I have attached screen shot of MP>co
I can open a session using KVM switch, but there i am getting
"X-Server cannot be started on display. For details look in the file, Dt login.errorLoffile( default:/var/dt/Xerrors)
**********************************************************
Suspending Desktop login
Desktop login will resume shortely after your logout."
The MP menu is functioning fine.
I have tried ctr L and ctr z but no response at MP console
Thanks
Jayan
Solved! Go to Solution.
- Mark as New
- Bookmark
- Subscribe
- Mute
- Subscribe to RSS Feed
- Permalink
- Report Inappropriate Content
тАО10-12-2008 07:48 PM
тАО10-12-2008 07:48 PM
Re: MP Console not responding
Use telnet to MP or LAN ip of server, if you are getting success then good.
Otherwiase you have to restart Hard Reboot.
Regards,
Gokul Chandola
- Mark as New
- Bookmark
- Subscribe
- Mute
- Subscribe to RSS Feed
- Permalink
- Report Inappropriate Content
тАО10-12-2008 07:48 PM
тАО10-12-2008 07:48 PM
Re: MP Console not responding
http://forums11.itrc.hp.com/service/forums/questionanswer.do?threadId=1249358
, but it doesn't help me.
Thanks
Jayan
- Mark as New
- Bookmark
- Subscribe
- Mute
- Subscribe to RSS Feed
- Permalink
- Report Inappropriate Content
тАО10-12-2008 07:57 PM
тАО10-12-2008 07:57 PM
Re: MP Console not responding
I am not able to assign MP ip so i cant telnet to MP.
Telnet is disabled so I can't login to LAN.
I have hard rebooted also, but same status.
Have attached MP LAN status
Jayan
- Mark as New
- Bookmark
- Subscribe
- Mute
- Subscribe to RSS Feed
- Permalink
- Report Inappropriate Content
тАО10-12-2008 08:03 PM
тАО10-12-2008 08:03 PM
SolutionAnd if your server is down or got hand in between booting process then go to MP> CM> RS. Reset the partition and check.
If no luck after this, register an hardware case with HP.
Thanks
SKR
- Mark as New
- Bookmark
- Subscribe
- Mute
- Subscribe to RSS Feed
- Permalink
- Report Inappropriate Content
тАО10-12-2008 08:16 PM
тАО10-12-2008 08:16 PM
Re: MP Console not responding
Server is up. I have rebooted again, but same status.
Thanks
Jayan
- Mark as New
- Bookmark
- Subscribe
- Mute
- Subscribe to RSS Feed
- Permalink
- Report Inappropriate Content
тАО10-12-2008 08:25 PM
тАО10-12-2008 08:25 PM
Re: MP Console not responding
From the output of lc at the CM prompt - it shows DHCP enabled.
If you want to give static ip address, subnet mask and default gateway to your MP console then can you try disabling the DHCP and then see if it allows you to assign an ip address.
Please check with your Network admin for the details of the ip,subnetmask and default gateway.
Regards,
Ninad
- Mark as New
- Bookmark
- Subscribe
- Mute
- Subscribe to RSS Feed
- Permalink
- Report Inappropriate Content
тАО10-12-2008 08:35 PM
тАО10-12-2008 08:35 PM
Re: MP Console not responding
I Assigned Mp IP.
But not able to connect MP by telnet.
- Mark as New
- Bookmark
- Subscribe
- Mute
- Subscribe to RSS Feed
- Permalink
- Report Inappropriate Content
тАО10-12-2008 09:02 PM
тАО10-12-2008 09:02 PM
Re: MP Console not responding
Let us first try to understand the problem.
Please confirm on the below points
1. Your server is up and running - so there is no problem on that front.
2. You want to be able to telnet the MP console and this is what you are not able to do.
Is there any other problem that we are missing out ?
You not being able to telnet to MP console IP address - there could be several reasons.
First let us understand from where you are trying to telnet.
Is the machine from which you are trying to telnet on the same subnet as the MP console IP address ?
If yes
Does telnet to some other machine work ?
Is telnet disabled ?
If no - (machine from which you are issuing the telnet tp MP console, and the MP console IP address are not in same subnet)
Is the subnet mask and default gateway on the MP console and the machine correctly configured ?
Are you able to ping the MP console IP address from your machine ?
Regards,
Ninad
- Mark as New
- Bookmark
- Subscribe
- Mute
- Subscribe to RSS Feed
- Permalink
- Report Inappropriate Content
тАО10-12-2008 09:23 PM
тАО10-12-2008 09:23 PM
Re: MP Console not responding
Server is up.
Remote MP login only through telnet.
Telnet is disabled to LAN ip.
Can able to ping to LAN ip, but can not connect to using SSH.
I am trying to telnet from my laptop, at network level routing has done different network is not a problem ( I can connect to other servers of different network).
Not able to ping to MP IP( I can ping MP ip of others HP machine of same network).
I have connected to MP console using usb serial cable
MP menu is working fine.
at console prompt it is stucked.
screent shoot attached.
I have opened a session using KVM switch but there not able to login and the message is
"X-Server cannot be started on display. For details look in the file, Dt login.errorLoffile( default:/var/dt/Xerrors)
**********************************************************
Suspending Desktop login
Desktop login will resume shortely after your logout."
Thanks
Jayan