- Community Home
- >
- Servers and Operating Systems
- >
- Integrity Servers
- >
- Re: Power Converter 1 and 3 Failed on an rx7640
Categories
Company
Local Language
Forums
Discussions
Forums
- Data Protection and Retention
- Entry Storage Systems
- Legacy
- Midrange and Enterprise Storage
- Storage Networking
- HPE Nimble Storage
Discussions
Discussions
Discussions
Forums
Forums
Discussions
Discussion Boards
Discussion Boards
Discussion Boards
Discussion Boards
- BladeSystem Infrastructure and Application Solutions
- Appliance Servers
- Alpha Servers
- BackOffice Products
- Internet Products
- HPE 9000 and HPE e3000 Servers
- Networking
- Netservers
- Secure OS Software for Linux
- Server Management (Insight Manager 7)
- Windows Server 2003
- Operating System - Tru64 Unix
- ProLiant Deployment and Provisioning
- Linux-Based Community / Regional
- Microsoft System Center Integration
Discussion Boards
Discussion Boards
Discussion Boards
Discussion Boards
Discussion Boards
Discussion Boards
Discussion Boards
Discussion Boards
Discussion Boards
Discussion Boards
Discussion Boards
Discussion Boards
Discussion Boards
Discussion Boards
Discussion Boards
Discussion Boards
Discussion Boards
Discussion Boards
Discussion Boards
Discussion Boards
Discussion Boards
Discussion Boards
Community
Resources
Forums
Blogs
- Subscribe to RSS Feed
- Mark Topic as New
- Mark Topic as Read
- Float this Topic for Current User
- Bookmark
- Subscribe
- Printer Friendly Page
- Mark as New
- Bookmark
- Subscribe
- Mute
- Subscribe to RSS Feed
- Permalink
- Report Inappropriate Content
тАО01-03-2010 12:32 PM
тАО01-03-2010 12:32 PM
After I installed HP IMA and SMH, I logged into the web page and I found a "Power Converter" Failure in the system tab.
I thought the problem is related to the server, but I have the same issue on 3 other servers (also rx7640).
Can you please tell me what is the problem and what should I do to resolve it ? (I see no anomalies on the server's led and the server is working fine)
Thanks.
Solved! Go to Solution.
- Mark as New
- Bookmark
- Subscribe
- Mute
- Subscribe to RSS Feed
- Permalink
- Report Inappropriate Content
тАО01-03-2010 02:00 PM
- Mark as New
- Bookmark
- Subscribe
- Mute
- Subscribe to RSS Feed
- Permalink
- Report Inappropriate Content
тАО01-03-2010 02:15 PM
тАО01-03-2010 02:15 PM
Re: Power Converter 1 and 3 Failed on an rx7640
- Mark as New
- Bookmark
- Subscribe
- Mute
- Subscribe to RSS Feed
- Permalink
- Report Inappropriate Content
тАО01-03-2010 11:59 PM
тАО01-03-2010 11:59 PM
Re: Power Converter 1 and 3 Failed on an rx7640
- Mark as New
- Bookmark
- Subscribe
- Mute
- Subscribe to RSS Feed
- Permalink
- Report Inappropriate Content
тАО01-04-2010 01:44 PM
тАО01-04-2010 01:44 PM
Re: Power Converter 1 and 3 Failed on an rx7640
Not sure? Then access the system MP and enter the Command Mode and run the command PS. Enter option T and you will see your AC Line Status. Now run the command PWRGRD and see what power mode the system is set for (single or dual grid).
-Bob
Was this helpful? Like this post by giving me a thumbs up below!
- Mark as New
- Bookmark
- Subscribe
- Mute
- Subscribe to RSS Feed
- Permalink
- Report Inappropriate Content
тАО01-04-2010 01:54 PM
тАО01-04-2010 01:54 PM
Re: Power Converter 1 and 3 Failed on an rx7640
Run PS from the MP:CM> and enter select the backplane. Check on the status of VRM's here as well.
-Bob
Was this helpful? Like this post by giving me a thumbs up below!
- Mark as New
- Bookmark
- Subscribe
- Mute
- Subscribe to RSS Feed
- Permalink
- Report Inappropriate Content
тАО01-04-2010 02:48 PM
тАО01-04-2010 02:48 PM
Re: Power Converter 1 and 3 Failed on an rx7640
I will check and let you know
- Mark as New
- Bookmark
- Subscribe
- Mute
- Subscribe to RSS Feed
- Permalink
- Report Inappropriate Content
тАО01-04-2010 07:23 PM
тАО01-04-2010 07:23 PM
Re: Power Converter 1 and 3 Failed on an rx7640
Line A0 Present
Line A1 NOT PRESENT
Line B0 Presnt
Line B1 NOT PRESENT
and the power configuration is single grid
I also checked the VRM's, no faults found.
So that means that the server is running on two AC line (I will check pysicallly when I get there).
On solution of course is to have the two AC lines, but if I choose to remain in this configuration, is there any way to disable this error from SMH ?
- Mark as New
- Bookmark
- Subscribe
- Mute
- Subscribe to RSS Feed
- Permalink
- Report Inappropriate Content
тАО01-05-2010 07:51 AM
тАО01-05-2010 07:51 AM
Re: Power Converter 1 and 3 Failed on an rx7640
I was wondering if it's not an IMA issue, I will try to upgrede IMA, installed one is 3.8.
Anything else I can check ?
- Mark as New
- Bookmark
- Subscribe
- Mute
- Subscribe to RSS Feed
- Permalink
- Report Inappropriate Content
тАО01-05-2010 01:39 PM
тАО01-05-2010 01:39 PM
Re: Power Converter 1 and 3 Failed on an rx7640
You could check system firmware though I did not see any fixes/enhancements relating to SMH.
From MP:CM> SYSREV
Some of the latest entities are:
Core IO MP : B.004.001.001
Core IO ED : 002.011.000
Cell PDHC : B.023.003.040
Cell IPF_FW : 009.048.000
-Bob
Was this helpful? Like this post by giving me a thumbs up below!