Problem with boot from DVD my rx7640

[Slawek Ksiazek]

Hi
I have new rx7640 and I try boot and install HPUX 11.31 but during boot (EFI)I have mesage

"Selected boot option: Internal DVD (Upper) Cabinet 0 [Acpi(HWP0002,PNP0A03,100)/Pci(3|1)/Scsi(Pun2,Lun0)]

Loading.: Internal DVD (Upper) Cabinet 0 [Acpi(HWP0002,PNP0A03,100)/Pci(3|1)/Scsi(Pun2,Lun0)]

Load of Internal DVD (Upper) Cabinet 0 [Acpi(HWP0002,PNP0A03,100)/Pci(3|1)/Scsi(Pun2,Lun0)] failed: Not Found

Press any key to continue"

What you think about my problem?How can i sove this problem?Please help me.Thanks a lot for help.


Slawek

[Torsten.]

Dump question ;-)

Do you have the cd in the upper internal drive? Or should it be the lower?

[Slawek Ksiazek]

Hi

I have in internal drive media DVD (HP Mission Critical 11.31 DVD 1 of 2)


Slawek

[Torsten.]

Go to EFI shell and run

Shell> reconnect -r
Shell> map -r

Do you see any fs_: entries, e.g. fs0:> ?

[Slawek Ksiazek]

In addition

mount /dev/dsk/c5t2d0 /dvdrom
/dev/dsk/c5t2d0: I/O error


Slawek

[Torsten.]

Check if you can read / mount the media in another system (you can even try it in your PC).

[Slawek Ksiazek]

I can read this dvd media on my laptop,

EFI Boot Manager ver 1.10 [14.61] Loading device drivers
EFI Boot Manager ver 1.10 [14.61] Please select a boot option
OS might use only the primary console set via boot manager or conconfig command

HP-UX Primary Boot: 0/0/0/3/0.0x6.0x0
LAN [Acpi(HWP0002,PNP0A03,101)/Pci(1|0)/Pci(6|0)/Mac(001CC4C5BA2
LAN [Acpi(HWP0002,PNP0A03,101)/Pci(1|0)/Pci(6|1)/Mac(001CC4C5BA2
LAN [Acpi(HWP0002,PNP0A03,102)/Pci(1|0)/Mac(001A4B07FFCE)]
LAN [Acpi(HWP0002,PNP0A03,102)/Pci(1|1)/Mac(001A4B07FFCF)]
LAN [Acpi(HWP0002,PNP0A03,1)/Pci(1|0)/Pci(6|0)/Mac(001CC4C5BA4C)
LAN [Acpi(HWP0002,PNP0A03,1)/Pci(1|0)/Pci(6|1)/Mac(001CC4C5BA4D)
LAN [Acpi(HWP0002,PNP0A03,2)/Pci(1|0)/Mac(001A4B07FDA6)]
LAN [Acpi(HWP0002,PNP0A03,2)/Pci(1|1)/Mac(001A4B07FDA7)]
EFI Shell [Built-in]
Internal DVD (Upper) Cabinet 0 [Acpi(HWP0002,PNP0A03,100)/Pci(3|
Boot Option Maintenance Menu


Use ^ and v to change option(s). Use Enter to select an option
Use > and < to view long descriptions
Hot Key: 'S' or 's' to start the EFI Shell

Selected boot option: EFI Shell [Built-in]

Loading.: EFI Shell [Built-in]

EFI Shell version 1.10 [14.61]
Device mapping table
fs0 : Acpi(HWP0002,PNP0A03,0)/Pci(3|0)/Scsi(Pun6,Lun0)/HD(Part1,Sig82DA0F42-2E12-11DD-8000-D6217B60E588)
fs1 : Acpi(HWP0002,PNP0A03,0)/Pci(3|0)/Scsi(Pun6,Lun0)/HD(Part3,Sig82DA0FA6-2E12-11DD-8000-D6217B60E588)
blk0 : Acpi(HWP0002,PNP0A03,0)/Pci(3|0)/Scsi(Pun6,Lun0)
blk1 : Acpi(HWP0002,PNP0A03,0)/Pci(3|0)/Scsi(Pun6,Lun0)/HD(Part1,Sig82DA0F42-2E12-11DD-8000-D6217B60E588)
blk2 : Acpi(HWP0002,PNP0A03,0)/Pci(3|0)/Scsi(Pun6,Lun0)/HD(Part2,Sig82DA0F88-2E12-11DD-8000-D6217B60E588)
blk3 : Acpi(HWP0002,PNP0A03,0)/Pci(3|0)/Scsi(Pun6,Lun0)/HD(Part3,Sig82DA0FA6-2E12-11DD-8000-D6217B60E588)
blk4 : Acpi(HWP0002,PNP0A03,1)/Pci(1|0)/Pci(4|1)/Scsi(Pun5,Lun0)
blk5 : Acpi(HWP0002,PNP0A03,100)/Pci(3|0)/Scsi(Pun6,Lun0)
blk6 : Acpi(HWP0002,PNP0A03,100)/Pci(3|1)/Scsi(Pun2,Lun0)
blk7 : Acpi(HWP0002,PNP0A03,101)/Pci(1|0)/Pci(4|1)/Scsi(Pun6,Lun0)

startup.nsh> echo -off

setting hpux path(\EFI\HPUX)...
type 'fs[x]:' where x is your bootdisk (0, 1, 2...)
type 'hpux' to start hpux bootloader
Shell> reconnect -r

Scsi(Pun6,Lun0) HP 300 GST3300655LC HPC8 (320 MBytes/sec)
Scsi(Pun5,Lun0) HP 300 GST3300655LC HPC8 (320 MBytes/sec)
PciRom S=00 B=70 D=1 F=0 I=3 loaded at 787FBABD000-787FBAF0000
HP PCI-X 2Port 4Gb Fibre Channel Adapter (driver 1.09, firmware 4.00.090)
HP PCI-X 2Port 4Gb Fibre Channel Adapter (driver 1.09, firmware 4.00.090)
HP PCI-X 2Port 4Gb Fibre Channel Adapter (driver 1.09, firmware 4.00.090)
HP PCI-X 2Port 4Gb Fibre Channel Adapter (driver 1.09, firmware 4.00.090)
HP PCI-X 2Port 4Gb Fibre Channel Adapter (driver 1.09, firmware 4.00.090)
HP PCI-X 2Port 4Gb Fibre Channel Adapter (driver 1.09, firmware 4.00.090)
Scsi(Pun6,Lun0) HP 300 GST3300655LC HPC8 (320 MBytes/sec)
Scsi(Pun2,Lun0) Optiarc DVD RW AD-5170A 1.32 ( 40 MBytes/sec)
Scsi(Pun6,Lun0) HP 300 GHUS153030VL3800 HPC1 (320 MBytes/sec)
HP PCI-X 2Port 4Gb Fibre Channel Adapter (driver 1.09, firmware 4.00.090)
HP PCI-X 2Port 4Gb Fibre Channel Adapter (driver 1.09, firmware 4.00.090)
PciRom S=01 B=8D D=4 F=0 I=0 loaded at 787FBA93000-787FBABD000
PciRom S=01 B=8D D=6 F=0 I=0 loaded at 40FFC3C000-40FFC76000

Copyright (c) 2000-2005 Broadcom Corporation
Broadcom NetXtreme Gigabit Ethernet EFI driver v7.0.11

HP 2Port 2Gb Fibre Channel Adapter (driver 1.47, firmware 3.03.154)
Broadcom NetXtreme Gigabit Ethernet (BCM5703) is detected (PCI-X)
HP PCI-X 2Port 4Gb Fibre Channel Adapter (driver 1.09, firmware 4.00.090)
HP PCI-X 2Port 4Gb Fibre Channel Adapter (driver 1.09, firmware 4.00.090)
HP PCI-X 2Port 4Gb Fibre Channel Adapter (driver 1.09, firmware 4.00.090)
HP PCI-X 2Port 4Gb Fibre Channel Adapter (driver 1.09, firmware 4.00.090)
ReconnectController(0,0,0) : Status = Success

Shell>
Shell> map -r
Device mapping table
fs0 : Acpi(HWP0002,PNP0A03,0)/Pci(3|0)/Scsi(Pun6,Lun0)/HD(Part1,Sig82DA0F42-2E12-11DD-8000-D6217B60E588)
fs1 : Acpi(HWP0002,PNP0A03,0)/Pci(3|0)/Scsi(Pun6,Lun0)/HD(Part3,Sig82DA0FA6-2E12-11DD-8000-D6217B60E588)
blk0 : Acpi(HWP0002,PNP0A03,0)/Pci(3|0)/Scsi(Pun6,Lun0)
blk1 : Acpi(HWP0002,PNP0A03,0)/Pci(3|0)/Scsi(Pun6,Lun0)/HD(Part1,Sig82DA0F42-2E12-11DD-8000-D6217B60E588)
blk2 : Acpi(HWP0002,PNP0A03,0)/Pci(3|0)/Scsi(Pun6,Lun0)/HD(Part2,Sig82DA0F88-2E12-11DD-8000-D6217B60E588)
blk3 : Acpi(HWP0002,PNP0A03,0)/Pci(3|0)/Scsi(Pun6,Lun0)/HD(Part3,Sig82DA0FA6-2E12-11DD-8000-D6217B60E588)
blk4 : Acpi(HWP0002,PNP0A03,1)/Pci(1|0)/Pci(4|1)/Scsi(Pun5,Lun0)
blk5 : Acpi(HWP0002,PNP0A03,100)/Pci(3|0)/Scsi(Pun6,Lun0)
blk6 : Acpi(HWP0002,PNP0A03,100)/Pci(3|1)/Scsi(Pun2,Lun0)
blk7 : Acpi(HWP0002,PNP0A03,101)/Pci(1|0)/Pci(4|1)/Scsi(Pun6,Lun0)

[Slawek Ksiazek]

still i can't boot i see

EFI Shell [Built-in]
Internal DVD (Upper) Cabinet 0 [Acpi(HWP0002,PNP0A03,100)/Pci(3|
Boot Option Maintenance Menu


Use ^ and v to change option(s). Use Enter to select an option
Use > and < to view long descriptions
Hot Key: 'S' or 's' to start the EFI Shell

Selected boot option: Internal DVD (Upper) Cabinet 0 [Acpi(HWP0002,PNP0A03,100)/Pci(3|1)/Scsi(Pun2,Lun0)]

Loading.: Internal DVD (Upper) Cabinet 0 [Acpi(HWP0002,PNP0A03,100)/Pci(3|1)/Scsi(Pun2,Lun0)]

Load of Internal DVD (Upper) Cabinet 0 [Acpi(HWP0002,PNP0A03,100)/Pci(3|1)/Scsi(Pun2,Lun0)] failed: Not Found

Press any key to continue

[Torsten.]

Devices are here:

Scsi(Pun6,Lun0) HP 300 GST3300655LC HPC8 (320 MBytes/sec)
Scsi(Pun2,Lun0) Optiarc DVD RW AD-5170A 1.32 ( 40 MBytes/sec)
Scsi(Pun6,Lun0) HP 300 GHUS153030VL3800 HPC1 (320 MBytes/sec)


this is
disk
dvd drive
disk

but the system cannot read the media. Can you try another bootable (for Integrity) media?

[Slawek Ksiazek]

I have other media with OS but I have this same situation,Plase tell me if on rx serwer are other media with OS than rp machines?


Slawek