Integrity Servers
cancel
Showing results for 
Search instead for 
Did you mean: 

RX2600 Has no Display

 
SOLVED
Go to solution
MALIK ADEEL IMTIAZ
Frequent Advisor

RX2600 Has no Display

Dear Torsten,

I have HP Server rx2600 when i push the start button it starts with red light then it converts in to orange after 3 to 4 minutes it again converts in to red light. And has no DISPLAY at all.

A time ago i had called a HP vendor he updates its BIO's i THINK problem starts from there.
Do you have any idea?

Thanks
Adeel Imtiaz
Netsol technologies.
67 REPLIES 67
Sharma Sanjeev
Respected Contributor

Re: RX2600 Has no Display

Hi Imtiaz Salaam

You have to cal HP Hardware Support for this
but you can check rx2600 is coming with two VGA Adapters also (One Onboard and one add on ).Check with other one.

Regards
Sanjeev
Everything is Possible as " IMPOSSIBLE" word itself says I M POSSIBLE
Torsten.
Acclaimed Contributor
Solution

Re: RX2600 Has no Display

The reason for this may be logged in the MP logs. Have a look, post them here or call HP support.

Hope this helps!
Regards
Torsten.

__________________________________________________
There are only 10 types of people in the world -
those who understand binary, and those who don't.

__________________________________________________
No support by private messages. Please ask the forum!

If you feel this was helpful please click the KUDOS! thumb below!   
MALIK ADEEL IMTIAZ
Frequent Advisor

Re: RX2600 Has no Display

Dear Torsten,
Problem is there is no display at all.

I have pressed the button of MP which is located behind the server but no moment at all.

Is there any jumper sitting's or any thing i can do to reset to get display i think HP person updates its Bios after that display went off. :(

Is there any way to get logs files.

Regards
Adeel Imtiaz
MALIK ADEEL IMTIAZ
Frequent Advisor

Re: RX2600 Has no Display

Dear Sanjeev,

There is only on VGA which is behind the server.

i Have not found another one. :p

Thanks
ADeel Imtiaz
Sharma Sanjeev
Respected Contributor

Re: RX2600 Has no Display

Dear Imtiaz Bhai

Que: Is there any way to get logs files.

If you know the IP Address of MP telnet to IP
from PC or connect Serial Port of laptop to MP and than check.

Regards
Sanjeev
Everything is Possible as " IMPOSSIBLE" word itself says I M POSSIBLE
MALIK ADEEL IMTIAZ
Frequent Advisor

Re: RX2600 Has no Display

Dear Sanjeev,

Thank you so much for you reply, actually red light is blinking continously and secondly i have connected to the console cable but it is not connecting means lan connection is not working.

thanks
Adeel Imtiaz
Highlighted
Sharma Sanjeev
Respected Contributor

Re: RX2600 Has no Display

Bhai Jaan

I mean to say Connect to Mp ( Serial Port )
with Laptop and than check did you get MP Prompt

Regards
Sanjeev
Everything is Possible as " IMPOSSIBLE" word itself says I M POSSIBLE
Torsten.
Acclaimed Contributor

Re: RX2600 Has no Display

You should see all the output until the OS is starting to boot on all console connections (the "normal" serial port, the MP console port, VGA).

Once the system is booting, output will *only* go to the default console.

Did you try to connect a VGA monitor already?

Hope this helps!
Regards
Torsten.

__________________________________________________
There are only 10 types of people in the world -
those who understand binary, and those who don't.

__________________________________________________
No support by private messages. Please ask the forum!

If you feel this was helpful please click the KUDOS! thumb below!   
MALIK ADEEL IMTIAZ
Frequent Advisor

Re: RX2600 Has no Display

Sir Jee,

Yahooo at last i have found the log which is attached.


Thanks
Adeel Imtiaz