- Community Home
- >
- Servers and Operating Systems
- >
- Integrity Servers
- >
- Re: Swapping boot drives from Rx2600 to RX2600 ser...
Integrity Servers
1753588
Members
6560
Online
108796
Solutions
Forums
Categories
Company
Local Language
юдл
back
Forums
Discussions
Forums
- Data Protection and Retention
- Entry Storage Systems
- Legacy
- Midrange and Enterprise Storage
- Storage Networking
- HPE Nimble Storage
Discussions
Discussions
Discussions
Forums
Forums
Discussions
юдл
back
Discussion Boards
Discussion Boards
Discussion Boards
Discussion Boards
- BladeSystem Infrastructure and Application Solutions
- Appliance Servers
- Alpha Servers
- BackOffice Products
- Internet Products
- HPE 9000 and HPE e3000 Servers
- Networking
- Netservers
- Secure OS Software for Linux
- Server Management (Insight Manager 7)
- Windows Server 2003
- Operating System - Tru64 Unix
- ProLiant Deployment and Provisioning
- Linux-Based Community / Regional
- Microsoft System Center Integration
Discussion Boards
Discussion Boards
Discussion Boards
Discussion Boards
Discussion Boards
Discussion Boards
Discussion Boards
Discussion Boards
Discussion Boards
Discussion Boards
Discussion Boards
Discussion Boards
Discussion Boards
Discussion Boards
Discussion Boards
Discussion Boards
Discussion Boards
Discussion Boards
Discussion Boards
Discussion Boards
Discussion Boards
Discussion Boards
Blogs
Information
Community
Resources
Community Language
Language
Forums
Blogs
Topic Options
- Subscribe to RSS Feed
- Mark Topic as New
- Mark Topic as Read
- Float this Topic for Current User
- Bookmark
- Subscribe
- Printer Friendly Page
- Mark as New
- Bookmark
- Subscribe
- Mute
- Subscribe to RSS Feed
- Permalink
- Report Inappropriate Content
тАО09-09-2003 11:24 AM
тАО09-09-2003 11:24 AM
Swapping boot drives from Rx2600 to RX2600 server
We are attempting to swap drives out of one RX2600 to another and are getting
Loading of HPUX primary boot; 0/1/1/0.1.0 failed:not found
This happens both ways - swapping each server's boot drives with the other's. When we place the server's own boot drives in, the servers boot fine.
Is there some special switch that needs to be set? This should not be that hard.
Loading of HPUX primary boot; 0/1/1/0.1.0 failed:not found
This happens both ways - swapping each server's boot drives with the other's. When we place the server's own boot drives in, the servers boot fine.
Is there some special switch that needs to be set? This should not be that hard.
2 REPLIES 2
- Mark as New
- Bookmark
- Subscribe
- Mute
- Subscribe to RSS Feed
- Permalink
- Report Inappropriate Content
тАО09-10-2003 08:21 AM
тАО09-10-2003 08:21 AM
Re: Swapping boot drives from Rx2600 to RX2600 server
Are you swapping the disk into the same location / path you mention (0/1/1/0.1.0)?
If not, check the EFI main menu where you can set the boot path. If your new disk is in a different place, you should be able to configure it and boot to it.
If not, check the EFI main menu where you can set the boot path. If your new disk is in a different place, you should be able to configure it and boot to it.
- Mark as New
- Bookmark
- Subscribe
- Mute
- Subscribe to RSS Feed
- Permalink
- Report Inappropriate Content
тАО10-23-2003 02:48 AM
тАО10-23-2003 02:48 AM
Re: Swapping boot drives from Rx2600 to RX2600 server
Sorry for the late response back. We ended up re-installing HPUX from scratch...
The driver are going in the exact same slots.
The driver are going in the exact same slots.
The opinions expressed above are the personal opinions of the authors, not of Hewlett Packard Enterprise. By using this site, you accept the Terms of Use and Rules of Participation.
News and Events
Support
© Copyright 2024 Hewlett Packard Enterprise Development LP