Integrity Servers
cancel
Showing results for 
Search instead for 
Did you mean: 

Unable to select FS0: to boot off the CD

 
SOLVED
Go to solution
dictum9
Super Advisor

Unable to select FS0: to boot off the CD

I cannot boot off the CD, when I do map -r I get just one LUN device. I cannot select any FSx: at all. 

reconnect -r shows 11 devices

 

12 REPLIES 12
dictum9
Super Advisor

Re: Unable to select FS0: to boot off the CD

the map commands shows just one line, one LUN and does not mention DVD.  How do I map DVD?

 

dictum9
Super Advisor

Re: Unable to select FS0: to boot off the CD

reconnect -r

Broadcom NetXtreme Gigabit Ethernet (BCM5703) is detected (PCI-X)
Scsi(Pun2,Lun0) _NEC DVD_RW ND-3540A 1.30 ( 40 MBytes/sec)
Scsi(Pun5,Lun0) HP Ultrium 3-SCSI G54D ( 80 MBytes/sec)
HP 2Port 2Gb Fibre Channel Adapter (driver 1.47, firmware 3.03.154)
Broadcom NetXtreme Gigabit Ethernet (BCM5703) is detected (PCI-X)
HP 2Port 2Gb Fibre Channel Adapter (driver 1.47, firmware 3.03.154)
Broadcom NetXtreme Gigabit Ethernet (BCM5703) is detected (PCI-X)
ReconnectController(0,0,0) : Status = Success

Shell>
Shell> map -r
Device mapping table
blk0 : Acpi(HWP0002,PNP0A03,0)/Pci(2|1)/Scsi(Pun2,Lun0)

Shell>

 

dictum9
Super Advisor

Re: Unable to select FS0: to boot off the CD

Shell> bcfg boot dump
The boot option list is:
01. Acpi(HWP0002,PNP0A03,C)/Pci(1|0)/Pci(4|0)/Fibre(WWN500143801136F009,Lun4001000000000000)/HD(Part1,Sig5923D410-66FB-11E5-8000-D6217B60E588)/\EFI\HPUX\HPUX.EFI "HP-UX Primary Boot: 0/0/12/1/0/4/0.0x500143801136f009.0x4001000000000000"
02. Acpi(HWP0002,PNP0A03,E)/Pci(1|0)/Pci(4|0)/Fibre(WWN50001FE1500940AD,Lun4001000000000000)/HD(Part1,Sig2A0D3110-EF8C-11DC-8002-D6217B60E588)/\EFI\HPUX\HPUX.EFI "HP-UX Alternate Boot: 0/0/14/1/0/4/0.1.2.0.0.0.1"
03. Acpi(HWP0002,PNP0A03,0)/Pci(1|0)/Mac(0018FE2884C3) "SYS LAN 0 Cabinet 0 [Acpi(HWP0002,PNP0A03,0)/Pci(1|0)/Mac(0018FE2884C3)]"
04. Acpi(HWP0002,PNP0A03,100)/Pci(1|0)/Mac(0018FE2884BF) "SYS LAN 1 Cabinet 0 [Acpi(HWP0002,PNP0A03,100)/Pci(1|0)/Mac(0018FE2884BF)]"
05. VenHw(D65A6B8C-71E5-4DF0-A909-F0D2992B5AA9) "EFI Shell [Built-in]"
06. Acpi(HWP0002,PNP0A03,100)/Pci(2|1)/Scsi(Pun2,Lun0) "Lower DVD" OPT
Shell> i(HWP0002,PNP0A03,100)/Pci(2|1)/Scsi(Pun2,Lun0) "Upper DVD" OPT
08. Acpi(HWP0002,PNP0A03,0)/Pci(3|1)/Scsi(Pun5,Lun0) "edwboot"
09. Acpi(HWP0002,PNP0A03,10E)/Pci(1|0)/Pci(4|0)/Fibre(WWN500143801136F00C,Lun4002000000000000)/HD(Part1,Sig425F5CB8-774E-11E1-8000-D6217B60E588)/\EFI\HPUX\HPUX.EFI "HP-UX HA Alternate Boot: 1/0/14/1/0/4/0.0x500143801136f00c.0x4002000000000000"
0A. Acpi(HWP0002,PNP0A03,0)/Pci(3|1)/Scsi(Pun5,Lun0) "edwbootoptinon"
0B. Acpi(HWP0002,PNP0A03,0)/Pci(2|1)/Scsi(Pun2,Lun0) "boot" OPT

Torsten.
Acclaimed Contributor

Re: Unable to select FS0: to boot off the CD

The drive itself is detected, so it could be a problem with the media.


Hope this helps!
Regards
Torsten.

__________________________________________________
There are only 10 types of people in the world -
those who understand binary, and those who don't.

__________________________________________________
No support by private messages. Please ask the forum!

If you feel this was helpful please click the KUDOS! thumb below!   
dictum9
Super Advisor

Re: Unable to select FS0: to boot off the CD

I am not even getting to the point where I boot off the CD.  It's not mapped. How do you map it?

 

Torsten.
Acclaimed Contributor

Re: Unable to select FS0: to boot off the CD

if there is a valid media in the drive, do "reconnect -r" and "map -r".


Hope this helps!
Regards
Torsten.

__________________________________________________
There are only 10 types of people in the world -
those who understand binary, and those who don't.

__________________________________________________
No support by private messages. Please ask the forum!

If you feel this was helpful please click the KUDOS! thumb below!   
dictum9
Super Advisor

Re: Unable to select FS0: to boot off the CD

When I try to map it, I get this:

 

Shell> bcfg boot add 0B "file.efi" "DVD"
bcfg: File file.efi - No mapping

dictum9
Super Advisor

Re: Unable to select FS0: to boot off the CD

Okay, I am getting somewhere. I put in the CD to another drive and got this. Looks encouraging.  Now what command do I issue to boot off the CD?

 

Broadcom NetXtreme Gigabit Ethernet (BCM5703) is detected (PCI-X)
Scsi(Pun2,Lun0) _NEC DVD_RW ND-3540A 1.30 ( 40 MBytes/sec)
Scsi(Pun5,Lun0) HP Ultrium 3-SCSI G54D ( 80 MBytes/sec)
HP 2Port 2Gb Fibre Channel Adapter (driver 1.47, firmware 3.03.154)
Broadcom NetXtreme Gigabit Ethernet (BCM5703) is detected (PCI-X)
HP 2Port 2Gb Fibre Channel Adapter (driver 1.47, firmware 3.03.154)
Broadcom NetXtreme Gigabit Ethernet (BCM5703) is detected (PCI-X)
ReconnectController(0,0,0) : Status = Success

Shell> map -r
Device mapping table
fs0 : Acpi(HWP0002,PNP0A03,0)/Pci(2|1)/Scsi(Pun2,Lun0)/CDROM(Entry0)
blk0 : Acpi(HWP0002,PNP0A03,0)/Pci(2|1)/Scsi(Pun2,Lun0)
blk1 : Acpi(HWP0002,PNP0A03,0)/Pci(2|1)/Scsi(Pun2,Lun0)/CDROM(Entry0)
blk2 : Acpi(HWP0002,PNP0A03,0)/Pci(2|1)/Scsi(Pun2,Lun0)/CDROM(Entry1)

Shell> fs0:

fs0:\> cd efi

fs0:\EFI> ls
Directory of: fs0:\EFI

 

Robert_Jewell
Honored Contributor
Solution

Re: Unable to select FS0: to boot off the CD

The output of the CDROM image doesnt look complete.  Here is an example of what you should see:

fs2:\> ls
Directory of: fs2:\

  06/17/11  02:26a <DIR>          1,024  EFI
  06/17/11  02:26a              698,868  INSTALL.EFI
  06/17/11  02:26a                   16  AUTO
  06/17/11  02:26a                  243  STARTUP.NSH
          3 File(s)     699,127 bytes
          1 Dir(s)

fs2:\> ls efi
Directory of: fs2:\efi

  06/17/11  02:26a <DIR>          1,024  .
  06/17/11  02:26a <DIR>              0  ..
  06/17/11  02:26a <DIR>          1,024  BOOT
  06/17/11  02:26a <DIR>          1,024  Intel_Firmware
  06/17/11  02:26a <DIR>          1,024  HP
          0 File(s)           0 bytes
          5 Dir(s)

Your installation disc doesnt appear to be correct or its corrupt.

To answer your question: from the fsX: location of the CD/DVD, you can run the command "install" to start the installation of HP-UX.

 

-Bob

----------------
Was this helpful? Like this post by giving me a thumbs up below!
dictum9
Super Advisor

Re: Unable to select FS0: to boot off the CD

That worked, thank you 

dictum9
Super Advisor

Re: Unable to select FS0: to boot off the CD

How do I get back to the EFI shell? 

 

Robert_Jewell
Honored Contributor

Re: Unable to select FS0: to boot off the CD

From what location?

If you are at a prompt such as fs2:/>  then you are at the EFI Shell.  The Shell> prompt is only shown when you first enter the shell without selecting any partitions to "reside" in.  You can enter commands as usual.

If you type "exit" you will get back to the Boot Manager screen.

 

-Bob

----------------
Was this helpful? Like this post by giving me a thumbs up below!