Integrity Servers
Showing results for 
Search instead for 
Did you mean: 

Voltage error???

Go to solution
Frequent Advisor

Voltage error???

what is mean???
(Voltage - 1.5V MR PwrGood)

Log Entry 19: 24 Mar 2007 09:35:55
Alert Level 2: Informational
Keyword: Type-02 090900 592128
Power unit disabled
Logged by: BMC; Sensor: Power Unit - Power Control
Data1: Device Disabled
0x204604F0FB020150 FFFF000943090300

Log Entry 18: 24 Mar 2007 09:35:54
Alert Level 2: Informational
Keyword: Type-02 226f05 2256645
ACPI state S5 (soft-off)
Logged by: BMC; Sensor: System ACPI Power State - ACPI State
Data1: S5/G2 soft-off
0x204604F0FA020140 FFFF056FFA220300

Log Entry 17: 24 Mar 2007 09:35:54
Alert Level 2: Informational
Keyword: Type-02 127003 1208323
Chassis Control request to BMC via IPMI or sensor
Logged by: BMC; Sensor: System Event
Data2: OEM Code2: 0xCD
0x204604F0FA020130 CD00A37000120300

Log Entry 16: 24 Mar 2007 09:35:53
Alert Level 5: Critical
Keyword: Type-02 020703 132867
Voltage reached critical level
Logged by: BMC; Sensor: Voltage - 1.5V MR PwrGood
Data1: transition to Non-recoverable from less severe
0x204604F0F9020120 FFFF0307CD020300

18 BMC 2 0x204604F0FA020140 FFFF056FFA220300 Type-02 226f05 2256645
24 Mar 2007 09:35:54
17 BMC 2 0x204604F0FA020130 CD00A37000120300 Type-02 127003 1208323
24 Mar 2007 09:35:54
16 BMC *5 0x204604F0F9020120 FFFF0307CD020300 Type-02 020703 132867
24 Mar 2007 09:35:53
15 BMC 2 0x204604F0E5020110 FFFF0103FDC00300 Type-02 c00301 12583681
24 Mar 2007 09:35:33
14 BMC 2 0x204604F0DD020100 FFFF027000120300 Type-02 127002 1208322
24 Mar 2007 09:35:25
13 BMC 2 0x204604F0DC0200F0 FFFF006FFA220300 Type-02 226f00 2256640
24 Mar 2007 09:35:24
12 BMC 2 0x204604F0DA0200E0 FFFF01EF62080300 Type-02 08ef01 585473
24 Mar 2007 09:35:22
11 BMC 2 0x204604F0DA0200D0 FFFF010943090300 Type-02 090901 592129
24 Mar 2007 09:35:22


Steven E. Protter
Exalted Contributor

Re: Voltage error???


If you are on UPS, check the batteries. If not, you have a power problem, either due to building power or a situation with your power supplies.

It needs to be investigated and corrected.

Steven E Protter
Owner of ISN Corporation
Frequent Advisor

Re: Voltage error???

server is rx4640 and not use UPS.
Super Advisor

Re: Voltage error???


can u log on to GSP and check the status of power supply.becaz normally rx4640 have redundant powersupply unit,if one fails ,normally will give alerts and check server VFU also for any attention LED blinking.if Attention LED blinking ,then check for the Logs in GSP.

Stefan Stechemesser
Honored Contributor

Re: Voltage error???

Hi Mark,

this is NOT an error related to the power supplies. It means that the sensor for the 1.5 V circuit on the I/O baseboard did not report Power Good anymore. The result was that the BMC shut down the system power to prevent damage (could be a hint on a shorted circuit ...).
This could be due to a failed component on that board. I would strongly recomend to call HP support and let them analyze this problem.

best regards