- Community Home
- >
- Servers and Operating Systems
- >
- Integrity Servers
- >
- Re: how to change vga to cli mode setting again on...
Categories
Company
Local Language
Forums
Discussions
Forums
- Data Protection and Retention
- Entry Storage Systems
- Legacy
- Midrange and Enterprise Storage
- Storage Networking
- HPE Nimble Storage
Discussions
Discussions
Discussions
Forums
Discussions
Discussion Boards
Discussion Boards
Discussion Boards
Discussion Boards
- BladeSystem Infrastructure and Application Solutions
- Appliance Servers
- Alpha Servers
- BackOffice Products
- Internet Products
- HPE 9000 and HPE e3000 Servers
- Networking
- Netservers
- Secure OS Software for Linux
- Server Management (Insight Manager 7)
- Windows Server 2003
- Operating System - Tru64 Unix
- ProLiant Deployment and Provisioning
- Linux-Based Community / Regional
- Microsoft System Center Integration
Discussion Boards
Discussion Boards
Discussion Boards
Discussion Boards
Discussion Boards
Discussion Boards
Discussion Boards
Discussion Boards
Discussion Boards
Discussion Boards
Discussion Boards
Discussion Boards
Discussion Boards
Discussion Boards
Discussion Boards
Discussion Boards
Discussion Boards
Discussion Boards
Discussion Boards
Community
Resources
Forums
Blogs
- Subscribe to RSS Feed
- Mark Topic as New
- Mark Topic as Read
- Float this Topic for Current User
- Bookmark
- Subscribe
- Printer Friendly Page
- Mark as New
- Bookmark
- Subscribe
- Mute
- Subscribe to RSS Feed
- Permalink
- Report Inappropriate Content
03-20-2014 03:37 AM - last edited on 03-20-2014 07:08 PM by Maiko-I
03-20-2014 03:37 AM - last edited on 03-20-2014 07:08 PM by Maiko-I
how to change vga to cli mode setting again on console.
Hi,
I changed bios setting efi serial to vga on console.
now
on server monitor
when i restart the server its not shown any messages and bios prompt
its automatic move to cde prompt .
how to change vga to cli mode setting
and i want to go bios ?
hot can do this.
thanks
P.S. This thread has been moevd from HP-UX > System Administration to Servers > Integrity. - Hp Forum MOderator
- Mark as New
- Bookmark
- Subscribe
- Mute
- Subscribe to RSS Feed
- Permalink
- Report Inappropriate Content
03-20-2014 04:58 AM
03-20-2014 04:58 AM
Re: how to change vga to cli mode setting again on console.
What server model do you have?
However, the most likely solution:
Boot to EFI shell and run "conconfig" to set either the MP serial connection as console.
Hope this helps!
Regards
Torsten.
__________________________________________________
There are only 10 types of people in the world -
those who understand binary, and those who don't.
__________________________________________________
No support by private messages. Please ask the forum!
If you feel this was helpful please click the KUDOS! thumb below!
- Mark as New
- Bookmark
- Subscribe
- Mute
- Subscribe to RSS Feed
- Permalink
- Report Inappropriate Content
03-20-2014 06:01 AM
03-20-2014 06:01 AM
Re: how to change vga to cli mode setting again on console.
Hi,
How to boot to EFI shell ?
because its automatic boot to gui
i am unable to see any boot logs or bios prompt ?
its totally blank screen
even i press any key but not happening
i also insert dvd on server but i unable to see any thing
only i see one cursur and after few minutes its go to cde mode
MODEL = RX6600 (hpux 11.31)
thanks
aamir
- Mark as New
- Bookmark
- Subscribe
- Mute
- Subscribe to RSS Feed
- Permalink
- Report Inappropriate Content
03-20-2014 06:09 AM
03-20-2014 06:09 AM
Re: how to change vga to cli mode setting again on console.
Connect to the serial MP connector.
Until the OS has booted, the POST and EFI output goes to all kind of output (serial and VGA).
If you see the boot menu, use arrow keys to select EFI. After a few minutes you will get an EFI prompt.
Now you can run "conconfig" to reconfigure the console.
However, you should see the same on the VGA screen.
Hope this helps!
Regards
Torsten.
__________________________________________________
There are only 10 types of people in the world -
those who understand binary, and those who don't.
__________________________________________________
No support by private messages. Please ask the forum!
If you feel this was helpful please click the KUDOS! thumb below!
- Mark as New
- Bookmark
- Subscribe
- Mute
- Subscribe to RSS Feed
- Permalink
- Report Inappropriate Content
03-20-2014 06:51 AM
03-20-2014 06:51 AM
Re: how to change vga to cli mode setting again on console.
Hi,
i dont have serial connector?
only rack tft connect to vga port
Please give me any another solution.
- Mark as New
- Bookmark
- Subscribe
- Mute
- Subscribe to RSS Feed
- Permalink
- Report Inappropriate Content
03-20-2014 06:54 AM
03-20-2014 06:54 AM
Re: how to change vga to cli mode setting again on console.
Get a serial null modem cable and connect with 9600 baud.
If the MP is configured for LAN access, you can do the change from LAN too.
Hope this helps!
Regards
Torsten.
__________________________________________________
There are only 10 types of people in the world -
those who understand binary, and those who don't.
__________________________________________________
No support by private messages. Please ask the forum!
If you feel this was helpful please click the KUDOS! thumb below!