- Community Home
- >
- Servers and Operating Systems
- >
- Integrity Servers
- >
- Re: npar reconfigue cpu & mem
Categories
Company
Local Language
Forums
Discussions
Forums
- Data Protection and Retention
- Entry Storage Systems
- Legacy
- Midrange and Enterprise Storage
- Storage Networking
- HPE Nimble Storage
Discussions
Discussions
Discussions
Forums
Forums
Discussions
Discussion Boards
Discussion Boards
Discussion Boards
Discussion Boards
- BladeSystem Infrastructure and Application Solutions
- Appliance Servers
- Alpha Servers
- BackOffice Products
- Internet Products
- HPE 9000 and HPE e3000 Servers
- Networking
- Netservers
- Secure OS Software for Linux
- Server Management (Insight Manager 7)
- Windows Server 2003
- Operating System - Tru64 Unix
- ProLiant Deployment and Provisioning
- Linux-Based Community / Regional
- Microsoft System Center Integration
Discussion Boards
Discussion Boards
Discussion Boards
Discussion Boards
Discussion Boards
Discussion Boards
Discussion Boards
Discussion Boards
Discussion Boards
Discussion Boards
Discussion Boards
Discussion Boards
Discussion Boards
Discussion Boards
Discussion Boards
Discussion Boards
Discussion Boards
Discussion Boards
Discussion Boards
Discussion Boards
Discussion Boards
Discussion Boards
Community
Resources
Forums
Blogs
- Subscribe to RSS Feed
- Mark Topic as New
- Mark Topic as Read
- Float this Topic for Current User
- Bookmark
- Subscribe
- Printer Friendly Page
- Mark as New
- Bookmark
- Subscribe
- Mute
- Subscribe to RSS Feed
- Permalink
- Report Inappropriate Content
тАО06-29-2006 11:08 PM
тАО06-29-2006 11:08 PM
I want to re-configure CPU's/Memory in 2nPar's on an rx7620.
The current setup is as follows:
nPar 0 : 8xCPU, 12GB RAM
nPar 1 : 8xCPU, 12GB RAM
Cell Information :
cell 0 : hpux 11.23(DEV)
cell 1 : hpux 11.23(WEB)
I whould like the following Configuration :
nPar 0 : 16xCPU, 24GB RAM
nPar 1 : idle(1~2month)
What is the best way to re-allocation of resources??
Solved! Go to Solution.
- Mark as New
- Bookmark
- Subscribe
- Mute
- Subscribe to RSS Feed
- Permalink
- Report Inappropriate Content
тАО06-29-2006 11:47 PM
тАО06-29-2006 11:47 PM
SolutionEach cell takes 4 sockets (4 CPU - 8 CPU dual-core) reason why if you want to put 16 CPUs on one npar you will need to remove the nPar1 add the 2├В┬║ cell board to nPar0.
parremove -p1 (- F if active)
parmodify -p0 -a1
And Reboot to reconfig.
Greetings
- Mark as New
- Bookmark
- Subscribe
- Mute
- Subscribe to RSS Feed
- Permalink
- Report Inappropriate Content
тАО06-30-2006 12:11 AM
тАО06-30-2006 12:11 AM
Re: npar reconfigue cpu & mem
Take care of the disks connected to nPar1, they will be connected to nPar0 then.
Hope this helps!
Regards
Torsten.
__________________________________________________
There are only 10 types of people in the world -
those who understand binary, and those who don't.
__________________________________________________
No support by private messages. Please ask the forum!
If you feel this was helpful please click the KUDOS! thumb below!
- Mark as New
- Bookmark
- Subscribe
- Mute
- Subscribe to RSS Feed
- Permalink
- Report Inappropriate Content
тАО06-30-2006 11:30 AM
тАО06-30-2006 11:30 AM
Re: npar reconfigue cpu & mem
after par1 is new os install??
- Mark as New
- Bookmark
- Subscribe
- Mute
- Subscribe to RSS Feed
- Permalink
- Report Inappropriate Content
тАО07-02-2006 09:08 AM
тАО07-02-2006 09:08 AM
Re: npar reconfigue cpu & mem
Take care and don't touch the disks while they belong to nPar0.
Hope this helps!
Regards
Torsten.
__________________________________________________
There are only 10 types of people in the world -
those who understand binary, and those who don't.
__________________________________________________
No support by private messages. Please ask the forum!
If you feel this was helpful please click the KUDOS! thumb below!
- Mark as New
- Bookmark
- Subscribe
- Mute
- Subscribe to RSS Feed
- Permalink
- Report Inappropriate Content
тАО07-03-2006 01:21 AM
тАО07-03-2006 01:21 AM
Re: npar reconfigue cpu & mem
This will erase complex config and recreate the complex so while defining you can create npar with cell0 and later add the other cell 1 also in this npar0 using parmodify command.