- Community Home
- >
- Servers and Operating Systems
- >
- Integrity Servers
- >
- Re: "Launching /stand/vmunix" freezes
Categories
Company
Local Language
Forums
Discussions
Forums
- Data Protection and Retention
- Entry Storage Systems
- Legacy
- Midrange and Enterprise Storage
- Storage Networking
- HPE Nimble Storage
Discussions
Discussions
Discussions
Forums
Discussions
Discussion Boards
Discussion Boards
Discussion Boards
Discussion Boards
- BladeSystem Infrastructure and Application Solutions
- Appliance Servers
- Alpha Servers
- BackOffice Products
- Internet Products
- HPE 9000 and HPE e3000 Servers
- Networking
- Netservers
- Secure OS Software for Linux
- Server Management (Insight Manager 7)
- Windows Server 2003
- Operating System - Tru64 Unix
- ProLiant Deployment and Provisioning
- Linux-Based Community / Regional
- Microsoft System Center Integration
Discussion Boards
Discussion Boards
Discussion Boards
Discussion Boards
Discussion Boards
Discussion Boards
Discussion Boards
Discussion Boards
Discussion Boards
Discussion Boards
Discussion Boards
Discussion Boards
Discussion Boards
Discussion Boards
Discussion Boards
Discussion Boards
Discussion Boards
Discussion Boards
Discussion Boards
Community
Resources
Forums
Blogs
- Subscribe to RSS Feed
- Mark Topic as New
- Mark Topic as Read
- Float this Topic for Current User
- Bookmark
- Subscribe
- Printer Friendly Page
- Mark as New
- Bookmark
- Subscribe
- Mute
- Subscribe to RSS Feed
- Permalink
- Report Inappropriate Content
04-27-2012 01:09 PM
04-27-2012 01:09 PM
Re: "Launching /stand/vmunix" freezes
Hi!
I am facing the same problem.
I tried the conconfig 2 primary. And now all my display is on 'COM' port (serial)
I am working on RX1620 machine.
I need to make the display the same on both the MP LAN and the serial connection (as I am familiar to on the the RX and RP servers I worked on before, 4000 series)
But as I see, I only have to chose between one of them to show me the output of CO.
Is there any way I can have this on this machine?
Also, I have another weird problem: In my serial console connection, I cannot see the MP page, it's directly in the CO output, and when I try to CTRL+B, it doesn't do anything. I have tried it on a new board also, same thing!
However, I can connect normally via the DB25 (console/UPS/remote) serial port.
Any help in these issues would be appreciated. :)
Thank you!
- Tags:
- mp
- Mark as New
- Bookmark
- Subscribe
- Mute
- Subscribe to RSS Feed
- Permalink
- Report Inappropriate Content
04-30-2012 12:20 PM
04-30-2012 12:20 PM
Re: "Launching /stand/vmunix" freezes
This is what you need to use.
The 9pin serial connector below can provide console, but it is not a part of the MP - hence no MP access!
Hope this helps!
Regards
Torsten.
__________________________________________________
There are only 10 types of people in the world -
those who understand binary, and those who don't.
__________________________________________________
No support by private messages. Please ask the forum!
If you feel this was helpful please click the KUDOS! thumb below!
- Mark as New
- Bookmark
- Subscribe
- Mute
- Subscribe to RSS Feed
- Permalink
- Report Inappropriate Content
05-14-2012 11:39 PM
05-14-2012 11:39 PM
Re: "Launching /stand/vmunix" freezes
Thanks heaps for this - an oldie but a goodie, caught us out today :)
- Mark as New
- Bookmark
- Subscribe
- Mute
- Subscribe to RSS Feed
- Permalink
- Report Inappropriate Content
07-17-2017 08:04 AM
07-17-2017 08:04 AM
Re: "Launching /stand/vmunix" freezes
well, when you are at below stage, just interrupt and type "boot vmunix -vga" .. no need to go through all menus
Press Any Key to interrupt Autoboot
\EFI\HPUX\AUTO ==> boot vmunix
Seconds left till autoboot - 9
- « Previous
-
- 1
- 2
- Next »