- Community Home
- >
- Servers and Operating Systems
- >
- Integrity Servers
- >
- Re: rx 2620 first time run - blank screen
Categories
Company
Local Language
Forums
Discussions
Forums
- Data Protection and Retention
- Entry Storage Systems
- Legacy
- Midrange and Enterprise Storage
- Storage Networking
- HPE Nimble Storage
Discussions
Discussions
Discussions
Forums
Forums
Discussions
Discussion Boards
Discussion Boards
Discussion Boards
Discussion Boards
- BladeSystem Infrastructure and Application Solutions
- Appliance Servers
- Alpha Servers
- BackOffice Products
- Internet Products
- HPE 9000 and HPE e3000 Servers
- Networking
- Netservers
- Secure OS Software for Linux
- Server Management (Insight Manager 7)
- Windows Server 2003
- Operating System - Tru64 Unix
- ProLiant Deployment and Provisioning
- Linux-Based Community / Regional
- Microsoft System Center Integration
Discussion Boards
Discussion Boards
Discussion Boards
Discussion Boards
Discussion Boards
Discussion Boards
Discussion Boards
Discussion Boards
Discussion Boards
Discussion Boards
Discussion Boards
Discussion Boards
Discussion Boards
Discussion Boards
Discussion Boards
Discussion Boards
Discussion Boards
Discussion Boards
Discussion Boards
Discussion Boards
Discussion Boards
Discussion Boards
Community
Resources
Forums
Blogs
- Subscribe to RSS Feed
- Mark Topic as New
- Mark Topic as Read
- Float this Topic for Current User
- Bookmark
- Subscribe
- Printer Friendly Page
- Mark as New
- Bookmark
- Subscribe
- Mute
- Subscribe to RSS Feed
- Permalink
- Report Inappropriate Content
тАО08-02-2005 06:45 PM
тАО08-02-2005 06:45 PM
Solved! Go to Solution.
- Mark as New
- Bookmark
- Subscribe
- Mute
- Subscribe to RSS Feed
- Permalink
- Report Inappropriate Content
тАО08-02-2005 07:10 PM
тАО08-02-2005 07:10 PM
SolutionIt is somehow standart for a newly purchased rx2620 not to operate properly for a VGA console. You need to correct this, if you feel that this is a fault for you.
First of all you must obtain a cross cable connected between rx and a laptop.
Second, a setup of local terminal access is required.
To setup local terminal access:
At the hyperterminal settings, set these values; parity-8/none, 9600 baud, receive-none, transmit-none...
- Mark as New
- Bookmark
- Subscribe
- Mute
- Subscribe to RSS Feed
- Permalink
- Report Inappropriate Content
тАО08-02-2005 07:24 PM
тАО08-02-2005 07:24 PM
Re: rx 2620 first time run - blank screen
http://forums1.itrc.hp.com/service/forums/questionanswer.do?threadId=942800
Hope this helps!
Regards
Torsten.
__________________________________________________
There are only 10 types of people in the world -
those who understand binary, and those who don't.
__________________________________________________
No support by private messages. Please ask the forum!
If you feel this was helpful please click the KUDOS! thumb below!
- Mark as New
- Bookmark
- Subscribe
- Mute
- Subscribe to RSS Feed
- Permalink
- Report Inappropriate Content
тАО08-02-2005 07:39 PM
тАО08-02-2005 07:39 PM
Re: rx 2620 first time run - blank screen
- Mark as New
- Bookmark
- Subscribe
- Mute
- Subscribe to RSS Feed
- Permalink
- Report Inappropriate Content
тАО08-02-2005 07:44 PM
тАО08-02-2005 07:44 PM
Re: rx 2620 first time run - blank screen
- Mark as New
- Bookmark
- Subscribe
- Mute
- Subscribe to RSS Feed
- Permalink
- Report Inappropriate Content
тАО08-02-2005 07:48 PM
тАО08-02-2005 07:48 PM
Re: rx 2620 first time run - blank screen
- Mark as New
- Bookmark
- Subscribe
- Mute
- Subscribe to RSS Feed
- Permalink
- Report Inappropriate Content
тАО08-02-2005 07:52 PM
тАО08-02-2005 07:52 PM
Re: rx 2620 first time run - blank screen
- Mark as New
- Bookmark
- Subscribe
- Mute
- Subscribe to RSS Feed
- Permalink
- Report Inappropriate Content
тАО08-02-2005 07:54 PM
тАО08-02-2005 07:54 PM
Re: rx 2620 first time run - blank screen
- Mark as New
- Bookmark
- Subscribe
- Mute
- Subscribe to RSS Feed
- Permalink
- Report Inappropriate Content
тАО08-02-2005 08:31 PM
тАО08-02-2005 08:31 PM
Re: rx 2620 first time run - blank screen
- Mark as New
- Bookmark
- Subscribe
- Mute
- Subscribe to RSS Feed
- Permalink
- Report Inappropriate Content
тАО08-02-2005 08:59 PM
тАО08-02-2005 08:59 PM
Re: rx 2620 first time run - blank screen
Open a dos prompt and type arp -s
Where Mac address or rx is written on a label at the front side of the server.(You'll need to pull it)
And IP address is probably 192.168.0.xxx since you've already established a simple network connection with cross-cables between rx and your PC... Make sure that both rx and your host PC shares the same subnet.
After executing this command, it is easy to connect to rx via telnet
By typing "telnet
You'll need to provide with the username and password as Admin,Admin
You'll reach the menu at this time.
From here it is possible to change default console access to VGA.