- Community Home
- >
- Servers and Operating Systems
- >
- Integrity Servers
- >
- Re: rx7640 ilo terminal problem
Categories
Company
Local Language
Forums
Discussions
Forums
- Data Protection and Retention
- Entry Storage Systems
- Legacy
- Midrange and Enterprise Storage
- Storage Networking
- HPE Nimble Storage
Discussions
Discussions
Discussions
Forums
Discussions
Discussion Boards
Discussion Boards
Discussion Boards
Discussion Boards
- BladeSystem Infrastructure and Application Solutions
- Appliance Servers
- Alpha Servers
- BackOffice Products
- Internet Products
- HPE 9000 and HPE e3000 Servers
- Networking
- Netservers
- Secure OS Software for Linux
- Server Management (Insight Manager 7)
- Windows Server 2003
- Operating System - Tru64 Unix
- ProLiant Deployment and Provisioning
- Linux-Based Community / Regional
- Microsoft System Center Integration
Discussion Boards
Discussion Boards
Discussion Boards
Discussion Boards
Discussion Boards
Discussion Boards
Discussion Boards
Discussion Boards
Discussion Boards
Discussion Boards
Discussion Boards
Discussion Boards
Discussion Boards
Discussion Boards
Discussion Boards
Discussion Boards
Discussion Boards
Discussion Boards
Discussion Boards
Community
Resources
Forums
Blogs
- Subscribe to RSS Feed
- Mark Topic as New
- Mark Topic as Read
- Float this Topic for Current User
- Bookmark
- Subscribe
- Printer Friendly Page
- Mark as New
- Bookmark
- Subscribe
- Mute
- Subscribe to RSS Feed
- Permalink
- Report Inappropriate Content
01-14-2019 10:09 PM
01-14-2019 10:09 PM
rx7640 ilo terminal problem
Hi All,
I used to connect to ILO on rp7640 using telnet, but sudenly the connection become like the following:
lt01@/home/tamimii/howto> telnet 10.148.90.50
Trying...
Connected to 10.148.90.50.
Escape character is '^]'.
Local flow control off
Connection closed by foreign host.
Then I couldn't connect to the terminal.
My questions:
- Can i reset the ILO terminal without rebooting it?
- If I need to reboot, do I need to do something to fix it?
Thank you,
Iwan
- Mark as New
- Bookmark
- Subscribe
- Mute
- Subscribe to RSS Feed
- Permalink
- Report Inappropriate Content
01-16-2019 05:36 AM
01-16-2019 05:36 AM
Re: rx7640 ilo terminal problem
Hello,
- Can i reset the ILO terminal without rebooting it?
Ans: You can try iLO reset (soft reset) by pressing (less than 3 seconds)the iLO reset button on the MP card and verify it.
- If I need to reboot, do I need to do something to fix it?
Ans: reboot won't help.. You may need to power cycle for the server to get the MP reset and verify.
Power cycle - removing AC power cable and insert back after 3 - 5 min.
Regards,
- Mark as New
- Bookmark
- Subscribe
- Mute
- Subscribe to RSS Feed
- Permalink
- Report Inappropriate Content
01-17-2019 09:01 PM
01-17-2019 09:01 PM
Re: rx7640 ilo terminal problem
Hi
Resetting the MP:
1) If a connection has already been established and the command menu is available, the MP can be reset through the 'xd' command by typing 'xd' at the 'CM>' prompt and selecting the option 3 to "Soft Reset the Master MP".
MP:CM>
MP:CM> XD
MP Diagnostics and Reboot menu
-------------
"3. Soft Reset the Master MP"
2) If a connection is not available, it will not be possible to establish a new one.
The MP must be reset by briefly pushing the button labeled "MP Reset" on the bulkhead of the CoreIO/MP board.
NOTE: If the MP Reset button is asserted for more than 5 seconds, MP settings stored in NVRAM will be reset to default values.
Hope This helps
[Any personal opinions expressed are mine, and not official statements on behalf of Hewlett Packard Enterprise]