- Community Home
- >
- Servers and Operating Systems
- >
- Integrity Servers
- >
- Re: rx7640 second cell fails to boot from DVD
Categories
Company
Local Language
Forums
Discussions
Forums
- Data Protection and Retention
- Entry Storage Systems
- Legacy
- Midrange and Enterprise Storage
- Storage Networking
- HPE Nimble Storage
Discussions
Discussions
Discussions
Forums
Forums
Discussions
Discussion Boards
Discussion Boards
Discussion Boards
Discussion Boards
- BladeSystem Infrastructure and Application Solutions
- Appliance Servers
- Alpha Servers
- BackOffice Products
- Internet Products
- HPE 9000 and HPE e3000 Servers
- Networking
- Netservers
- Secure OS Software for Linux
- Server Management (Insight Manager 7)
- Windows Server 2003
- Operating System - Tru64 Unix
- ProLiant Deployment and Provisioning
- Linux-Based Community / Regional
- Microsoft System Center Integration
Discussion Boards
Discussion Boards
Discussion Boards
Discussion Boards
Discussion Boards
Discussion Boards
Discussion Boards
Discussion Boards
Discussion Boards
Discussion Boards
Discussion Boards
Discussion Boards
Discussion Boards
Discussion Boards
Discussion Boards
Discussion Boards
Discussion Boards
Discussion Boards
Discussion Boards
Discussion Boards
Discussion Boards
Discussion Boards
Community
Resources
Forums
Blogs
- Subscribe to RSS Feed
- Mark Topic as New
- Mark Topic as Read
- Float this Topic for Current User
- Bookmark
- Subscribe
- Printer Friendly Page
- Mark as New
- Bookmark
- Subscribe
- Mute
- Subscribe to RSS Feed
- Permalink
- Report Inappropriate Content
тАО02-05-2008 05:54 AM
тАО02-05-2008 05:54 AM
Booting kernel
MCA event occurred ....
sequencer: The MCA was NOT corrected. A cold boot is required.
sequencer: Resetting...
The SL Logs are attached. The initial error seems to be WRITE_MCA_LOGS_TO_DISK_FAILED
Any suggestions?
Solved! Go to Solution.
- Mark as New
- Bookmark
- Subscribe
- Mute
- Subscribe to RSS Feed
- Permalink
- Report Inappropriate Content
тАО02-06-2008 01:56 AM
тАО02-06-2008 01:56 AM
Re: rx7640 second cell fails to boot from DVD
How many DVD's do you have on the system?
When looking at the front left, the lower DVD is for Cell0, if another is installed above this, directly below the Front Panel, then this one is connected to Cell 1.
Are you trying to install from the correct DVD unit, and do you have one which is "connected" to Cell 1?
Regards,
Phil
- Mark as New
- Bookmark
- Subscribe
- Mute
- Subscribe to RSS Feed
- Permalink
- Report Inappropriate Content
тАО02-06-2008 02:29 AM
тАО02-06-2008 02:29 AM
Re: rx7640 second cell fails to boot from DVD
We have one externally connected DVD. It is into the combo card in slot 8.
The new cell board is cell 0 and is the only cell for this partition. 'search 0' shows the following -
Scsi(Pun6,Lun0) HP 146 GST3146855LC HPC8 (320 MBytes/sec)
Scsi(Pun2,Lun0) _NEC DVD_RW ND-3550A 1.31 ( 80 MBytes/sec)
Scsi(Pun5,Lun0) HP 146 GST3146855LC HPC8 (320 MBytes/sec)
HP PCI-X 2Port 4Gb Fibre Channel Adapter (driver 1.09, firmware 4.00.090)
HP PCI-X 2Port 4Gb Fibre Channel Adapter (driver 1.09, firmware 4.00.090)
It does load from DVD and shows various messages before the 'MCA event'
- Mark as New
- Bookmark
- Subscribe
- Mute
- Subscribe to RSS Feed
- Permalink
- Report Inappropriate Content
тАО02-06-2008 02:39 AM
тАО02-06-2008 02:39 AM
Re: rx7640 second cell fails to boot from DVD
What OS are you trying to install?
Cheers,
Phil
- Mark as New
- Bookmark
- Subscribe
- Mute
- Subscribe to RSS Feed
- Permalink
- Report Inappropriate Content
тАО02-06-2008 02:51 AM
тАО02-06-2008 02:51 AM
Re: rx7640 second cell fails to boot from DVD
- Mark as New
- Bookmark
- Subscribe
- Mute
- Subscribe to RSS Feed
- Permalink
- Report Inappropriate Content
тАО02-06-2008 03:14 AM
тАО02-06-2008 03:14 AM
Re: rx7640 second cell fails to boot from DVD
Are your ACPICONFIG settings set for HPUX?
type
SHELL> acpiconfig
the resultant should say "DEFAULT".
If the resultant is "WINDOWS", then you will need to change it.
Can you post the MCA?
capture the following:
SHELL> errdump mca
Phil
- Mark as New
- Bookmark
- Subscribe
- Mute
- Subscribe to RSS Feed
- Permalink
- Report Inappropriate Content
тАО02-06-2008 04:18 AM
тАО02-06-2008 04:18 AM
Re: rx7640 second cell fails to boot from DVD
The acpiconfig is set to default. I've attached the MCA errdump.
- Mark as New
- Bookmark
- Subscribe
- Mute
- Subscribe to RSS Feed
- Permalink
- Report Inappropriate Content
тАО02-06-2008 05:28 AM
тАО02-06-2008 05:28 AM
Re: rx7640 second cell fails to boot from DVD
What is the release date of your install media?
Hope this helps!
Regards
Torsten.
__________________________________________________
There are only 10 types of people in the world -
those who understand binary, and those who don't.
__________________________________________________
No support by private messages. Please ask the forum!
If you feel this was helpful please click the KUDOS! thumb below!
- Mark as New
- Bookmark
- Subscribe
- Mute
- Subscribe to RSS Feed
- Permalink
- Report Inappropriate Content
тАО02-06-2008 05:45 AM
тАО02-06-2008 05:45 AM
SolutionDo you have an HBA installed in slot 4 (LBA14) of Chassis 0?
If so, what is attached to it?
If anything is connected to it, then disconnect and try install of OS.
Otherwise, remove the HBA from slot 4 (LBA14) and try to install the OS.
Cheers,
Phil
- Mark as New
- Bookmark
- Subscribe
- Mute
- Subscribe to RSS Feed
- Permalink
- Report Inappropriate Content
тАО02-06-2008 08:16 AM
тАО02-06-2008 08:16 AM
Re: rx7640 second cell fails to boot from DVD
Yes, I am supposed to have an HBA installed in slot 4 as well as the one showing in slot 3. I now see that in 'info all' (attached) it isn't showing except as an occupied slot.
I'll investigate that..