- Community Home
- >
- Networking
- >
- Switching and Routing
- >
- LAN Routing
- >
- Re: [A5500] Debug packet ip / icmp ?
Categories
Company
Local Language
Forums
Discussions
Forums
- Data Protection and Retention
- Entry Storage Systems
- Legacy
- Midrange and Enterprise Storage
- Storage Networking
- HPE Nimble Storage
Discussions
Discussions
Discussions
Forums
Discussions
Discussion Boards
Discussion Boards
Discussion Boards
Discussion Boards
- BladeSystem Infrastructure and Application Solutions
- Appliance Servers
- Alpha Servers
- BackOffice Products
- Internet Products
- HPE 9000 and HPE e3000 Servers
- Networking
- Netservers
- Secure OS Software for Linux
- Server Management (Insight Manager 7)
- Windows Server 2003
- Operating System - Tru64 Unix
- ProLiant Deployment and Provisioning
- Linux-Based Community / Regional
- Microsoft System Center Integration
Discussion Boards
Discussion Boards
Discussion Boards
Discussion Boards
Discussion Boards
Discussion Boards
Discussion Boards
Discussion Boards
Discussion Boards
Discussion Boards
Discussion Boards
Discussion Boards
Discussion Boards
Discussion Boards
Discussion Boards
Discussion Boards
Discussion Boards
Discussion Boards
Discussion Boards
Community
Resources
Forums
Blogs
- Subscribe to RSS Feed
- Mark Topic as New
- Mark Topic as Read
- Float this Topic for Current User
- Bookmark
- Subscribe
- Printer Friendly Page
- Mark as New
- Bookmark
- Subscribe
- Mute
- Subscribe to RSS Feed
- Permalink
- Report Inappropriate Content
03-22-2016 01:35 AM
03-22-2016 01:35 AM
Hi All,
I want to debug ip packet but I have a weird behavior...
I type in user view :
debugging ip packet
debugging ip icmp
The "display debugging" shows me that the above commands are on.
Then "term debugging" and "term mon" : ok, I see informations.
I configure Putty to log all this informations in a file.
I type from a device "ping <one ip>" and I open the log file : I search IP source or destintion but nothing.
The route is :
UTM (10.0.5.11) <> H3C VLAN1002 (10.0.5.9) <> H3C VLAN100 (10.0.0.252) <> CPE (10.0.0.204) <> DEVICE (10.3.239.254)
I check the route and it is correct.
Any ideas, friends ?
Regards,
Jacques
Solved! Go to Solution.
- Mark as New
- Bookmark
- Subscribe
- Mute
- Subscribe to RSS Feed
- Permalink
- Report Inappropriate Content
03-22-2016 08:22 AM
03-22-2016 08:22 AM
Re: [A5500] Debug packet ip / icmp ?
Pprobably, pinging through the device is handled by hardware , and might not show up in debug. Pinging the device itself is handled by software , and should show up in debug.
- Mark as New
- Bookmark
- Subscribe
- Mute
- Subscribe to RSS Feed
- Permalink
- Report Inappropriate Content
03-22-2016 08:44 AM
03-22-2016 08:44 AM
Re: [A5500] Debug packet ip / icmp ?
Bonjour 16again !
Always there to help me ! :)
You're right...
So, how can I debug flow packet (without to configure a port mirroring) through the switch between 2 devices ?
- Mark as New
- Bookmark
- Subscribe
- Mute
- Subscribe to RSS Feed
- Permalink
- Report Inappropriate Content
03-23-2016 03:35 AM
- Mark as New
- Bookmark
- Subscribe
- Mute
- Subscribe to RSS Feed
- Permalink
- Report Inappropriate Content
03-23-2016 03:42 AM
03-23-2016 03:42 AM
Re: [A5500] Debug packet ip / icmp ?
Thank you, it's resolved :)