- Community Home
- >
- Networking
- >
- Switching and Routing
- >
- LAN Routing
- >
- Re: Ip Route with switch Aruba 2930M
-
- Forums
-
- Advancing Life & Work
- Advantage EX
- Alliances
- Around the Storage Block
- HPE Ezmeral: Uncut
- OEM Solutions
- Servers & Systems: The Right Compute
- Tech Insights
- The Cloud Experience Everywhere
- HPE Blog, Austria, Germany & Switzerland
- Blog HPE, France
- HPE Blog, Italy
- HPE Blog, Japan
- HPE Blog, Middle East
- HPE Blog, Russia
- HPE Blog, Saudi Arabia
- HPE Blog, South Africa
- HPE Blog, UK & Ireland
-
Blogs
- Advancing Life & Work
- Advantage EX
- Alliances
- Around the Storage Block
- HPE Blog, Latin America
- HPE Blog, Middle East
- HPE Blog, Saudi Arabia
- HPE Blog, South Africa
- HPE Blog, UK & Ireland
- HPE Ezmeral: Uncut
- OEM Solutions
- Servers & Systems: The Right Compute
- Tech Insights
- The Cloud Experience Everywhere
-
Information
- Community
- Welcome
- Getting Started
- FAQ
- Ranking Overview
- Rules of Participation
- Tips and Tricks
- Resources
- Announcements
- Email us
- Feedback
- Information Libraries
- Integrated Systems
- Networking
- Servers
- Storage
- Other HPE Sites
- Support Center
- Aruba Airheads Community
- Enterprise.nxt
- HPE Dev Community
- Cloud28+ Community
- Marketplace
-
Forums
-
Blogs
-
Information
-
English
- Subscribe to RSS Feed
- Mark Topic as New
- Mark Topic as Read
- Float this Topic for Current User
- Bookmark
- Subscribe
- Printer Friendly Page
- Mark as New
- Bookmark
- Subscribe
- Mute
- Subscribe to RSS Feed
- Permalink
- Email to a Friend
- Report Inappropriate Content
05-29-2018 05:00 AM
05-29-2018 05:00 AM
Ip Route with switch Aruba 2930M
Hi everybody !
I just received a switch Aruba 2930M in replacement of a switch Avaya 5520, now, I have to configure it but I have a big problem.
When I writte the command "ip route 0.0.0.0 0.0.0.0 X.X.X.X" I don't see my route with the command "show ip route" and I don't understant why it don't work.
The IP Routing is activate, the Vlans created and each one have a IP address.
Can you help me please ?
Thank you so much.
- Mark as New
- Bookmark
- Subscribe
- Mute
- Subscribe to RSS Feed
- Permalink
- Email to a Friend
- Report Inappropriate Content
05-29-2018 10:12 AM
05-29-2018 10:12 AM
Re: Ip Route with switch Aruba 2930M
Have you tried to set the Default Route by using the ip route 0.0.0.0/0 x.x.x.x syntax for the ip route command?
I'm not an HPE Employee

- Mark as New
- Bookmark
- Subscribe
- Mute
- Subscribe to RSS Feed
- Permalink
- Email to a Friend
- Report Inappropriate Content
05-29-2018 03:12 PM
05-29-2018 03:12 PM
Re: Ip Route with switch Aruba 2930M
Can we assume the static route target you are setting is an address within a connected subnet on the switch?
Seeing as they were threatening to mix up 3COM commands onto the Procurve OS, the first thing I would try is the same command, but without the "e" at the end of "ip route", because that takes only a few seconds to test.
Then I would enable
debug dest sess
debug all
Then run the command again.
- Mark as New
- Bookmark
- Subscribe
- Mute
- Subscribe to RSS Feed
- Permalink
- Email to a Friend
- Report Inappropriate Content
05-30-2018 12:03 AM
05-30-2018 12:03 AM
Re: Ip Route with switch Aruba 2930M
Good morning Vince-Whirlwind,
Can we assume the static route target you are setting is an address within a connected subnet on the switch?
Yes, I'm sure because I created a Vlan with the same subnet for example :
Vlan1
IP address = 10.10.10.1/24
and for my route
ip route 0.0.0.0/0 10.10.10.1
The command work correctly but I don't see when I do show ip route.
However, when I write the command "show config", I see the route that I created and I don't understand why with this one function it's ok and not with "show config" ?
I tried your command "ip rout" (I deleted the "e") but it doesn't work, I have the message "Ambiguous input : rout"
Thank you so much for your help
- Mark as New
- Bookmark
- Subscribe
- Mute
- Subscribe to RSS Feed
- Permalink
- Email to a Friend
- Report Inappropriate Content
05-30-2018 04:29 PM
05-30-2018 04:29 PM
Re: Ip Route with switch Aruba 2930M
I'm not sure a static route targetting a local address is much use - where is it you want that traffic to actually go? Target the remote interface on the 10.10.10.0 subnet.
- Mark as New
- Bookmark
- Subscribe
- Mute
- Subscribe to RSS Feed
- Permalink
- Email to a Friend
- Report Inappropriate Content
05-31-2018 09:36 PM
05-31-2018 09:36 PM
Re: Ip Route with switch Aruba 2930M
Hi Vince,
want to tell my switch that all IP addresses outside my Vlans are routed to my router that has the IP address 10.10.10.1
For example :
Vlan1 = ip route 192.168.10.0/24 192.168.10.1
Vlan2 = ip route 192.168.20.0/24 192.168.20.1
Vlan3 = ip route 192.168.30.0/24 192.168.30.1
The IP addresses 192.168.10.1, 192.168.20.1 and 192.168.30.1 are IP addresses of the Vlans that I declared in my switch Aruba 2930M.
Thank you so much for your help me.
- Mark as New
- Bookmark
- Subscribe
- Mute
- Subscribe to RSS Feed
- Permalink
- Email to a Friend
- Report Inappropriate Content
05-31-2018 09:44 PM
05-31-2018 09:44 PM
Re: Ip Route with switch Aruba 2930M
I don't quite understand what that example means.
Can you show your switch config, all the VLAN interface IP addressing, and specify what the router's ip config is for the subnet it shares with the switch.
Hewlett Packard Enterprise International
- Communities
- HPE Blogs and Forum
© Copyright 2021 Hewlett Packard Enterprise Development LP