- Community Home
- >
- Networking
- >
- Switching and Routing
- >
- LAN Routing
- >
- Re: Separating Test Environment
Categories
Company
Local Language
Forums
Discussions
Forums
- Data Protection and Retention
- Entry Storage Systems
- Legacy
- Midrange and Enterprise Storage
- Storage Networking
- HPE Nimble Storage
Discussions
Discussions
Discussions
Forums
Forums
Discussions
Discussion Boards
Discussion Boards
Discussion Boards
Discussion Boards
- BladeSystem Infrastructure and Application Solutions
- Appliance Servers
- Alpha Servers
- BackOffice Products
- Internet Products
- HPE 9000 and HPE e3000 Servers
- Networking
- Netservers
- Secure OS Software for Linux
- Server Management (Insight Manager 7)
- Windows Server 2003
- Operating System - Tru64 Unix
- ProLiant Deployment and Provisioning
- Linux-Based Community / Regional
- Microsoft System Center Integration
Discussion Boards
Discussion Boards
Discussion Boards
Discussion Boards
Discussion Boards
Discussion Boards
Discussion Boards
Discussion Boards
Discussion Boards
Discussion Boards
Discussion Boards
Discussion Boards
Discussion Boards
Discussion Boards
Discussion Boards
Discussion Boards
Discussion Boards
Discussion Boards
Discussion Boards
Discussion Boards
Discussion Boards
Discussion Boards
Community
Resources
Forums
Blogs
- Subscribe to RSS Feed
- Mark Topic as New
- Mark Topic as Read
- Float this Topic for Current User
- Bookmark
- Subscribe
- Printer Friendly Page
- Mark as New
- Bookmark
- Subscribe
- Mute
- Subscribe to RSS Feed
- Permalink
- Report Inappropriate Content
тАО12-27-2013 09:37 AM - edited тАО12-27-2013 09:56 AM
тАО12-27-2013 09:37 AM - edited тАО12-27-2013 09:56 AM
Separating Test Environment
Currently using PRoCurve E5412
As I am implemeting a test environment I see myslef looking for complete separation from our production.
I am looking to get some logical support.
Currently the only configuration I have made are through the VLAN configs.
I have untagged to ProCurve interfaces: A12 and C12.
And made sure all other VLAN configs do not unclude these; A12 and C12.
But I am able to still ping the production network.
What should I be looking at to complete this separation?
Forgot to mention that this is behind a watchguard firewall > Just mentioned firewall for logical help.
I would like to put the load on the HP Procurve and not the firewall unless the firewall is needed.
- Mark as New
- Bookmark
- Subscribe
- Mute
- Subscribe to RSS Feed
- Permalink
- Report Inappropriate Content
тАО01-01-2014 01:16 PM
тАО01-01-2014 01:16 PM
Re: Separating Test Environment
- Mark as New
- Bookmark
- Subscribe
- Mute
- Subscribe to RSS Feed
- Permalink
- Report Inappropriate Content
тАО01-02-2014 06:40 AM
тАО01-02-2014 06:40 AM
Re: Separating Test Environment
Thank you for the response.
However the issue has been sovled.
-ReSolved-
- Mark as New
- Bookmark
- Subscribe
- Mute
- Subscribe to RSS Feed
- Permalink
- Report Inappropriate Content
тАО01-02-2014 12:02 PM - edited тАО01-02-2014 01:28 PM
тАО01-02-2014 12:02 PM - edited тАО01-02-2014 01:28 PM
Re: Separating Test Environment
I would like to re-open this ticket.
I was able to get separation via ACL.
Clients cannot ping each other across production network and test network, visa versa.
Although clients can ping ip addresses assigned to VLANS across networks (Gateways).
Static routing is what I am going to look at next, as this is what is used.
Current static routing is a null route
Any advice would be good.
thanks, >