- Community Home
- >
- Networking
- >
- Switching and Routing
- >
- LAN Routing
- >
- VPN issue HP Procurve Secure Router 7102dl
Categories
Company
Local Language
Forums
Discussions
Forums
- Data Protection and Retention
- Entry Storage Systems
- Legacy
- Midrange and Enterprise Storage
- Storage Networking
- HPE Nimble Storage
Discussions
Discussions
Discussions
Forums
Discussions
Discussion Boards
Discussion Boards
Discussion Boards
Discussion Boards
- BladeSystem Infrastructure and Application Solutions
- Appliance Servers
- Alpha Servers
- BackOffice Products
- Internet Products
- HPE 9000 and HPE e3000 Servers
- Networking
- Netservers
- Secure OS Software for Linux
- Server Management (Insight Manager 7)
- Windows Server 2003
- Operating System - Tru64 Unix
- ProLiant Deployment and Provisioning
- Linux-Based Community / Regional
- Microsoft System Center Integration
Discussion Boards
Discussion Boards
Discussion Boards
Discussion Boards
Discussion Boards
Discussion Boards
Discussion Boards
Discussion Boards
Discussion Boards
Discussion Boards
Discussion Boards
Discussion Boards
Discussion Boards
Discussion Boards
Discussion Boards
Discussion Boards
Discussion Boards
Discussion Boards
Discussion Boards
Community
Resources
Forums
Blogs
- Subscribe to RSS Feed
- Mark Topic as New
- Mark Topic as Read
- Float this Topic for Current User
- Bookmark
- Subscribe
- Printer Friendly Page
- Mark as New
- Bookmark
- Subscribe
- Mute
- Subscribe to RSS Feed
- Permalink
- Report Inappropriate Content
09-14-2011 11:47 AM
09-14-2011 11:47 AM
VPN issue HP Procurve Secure Router 7102dl
I am having an issue getting to the vpn attached network from a sub-interface network on a Procurve 7102dl Secure Router.
The setup is as follows:
Remote site connects to a 71020DL secure router via a Netgear Prosafe VPN firewall appliance. The remote site connects as expected to eth 0/1 (Public) and is accessible from traffic coming from eth 0/2.1 (Private 192.168.x.x) on the Procurve.
Traffic coming from eth 0/2.4 (Private 10.1.x.x) on the procurve can not see the remote site. Can not ping or trace route to the remote network. Both time out. A check of the policy "Data" during a ping shows its attempting to go out the public interface.
I have added the 10.x.x.x network to the vpn access list statement (see below) without any luck. I have also added the same allow statement on the Policy connected to the 0/2.4 interface as is on the Policy connected to interface 0/2.1. That didn't do the trick either. Any ideas?
interface eth 0/1
description
ip address 66.x.x.x 255.255.255.252
access-policy Public
crypto map VPN
no shutdown
interface eth 0/2.1
description MMH Private Network sub int
vlan-id 1 native
ip address 192.168.10.2 255.255.255.0
ip rip receive version 2
ip rip send version 2
access-policy Private
no shutdown
interface eth 0/2.4
description Production Gateway Voice and Data .1
vlan-id 10
ip address 10.1.0.2 255.255.252.0
access-policy DATA
ip access-list extended VPN-10-vpn-selectors
permit ip any 192.168.0.0 0.0.255.255 log
permit ip any 10.0.0.0 0.255.255.255 log
deny ip any any
ip policy-class Public
allow reverse list VPN-10-vpn-selectors stateless
ip policy-class Public
allow reverse list VPN-10-vpn-selectors stateless
ip policy-class Data
allow reverse list VPN-10-vpn-selectors stateless