- Community Home
- >
- Networking
- >
- Switching and Routing
- >
- LAN Routing
- >
- no ip routing hp 2910
Categories
Company
Local Language
Forums
Discussions
Forums
- Data Protection and Retention
- Entry Storage Systems
- Legacy
- Midrange and Enterprise Storage
- Storage Networking
- HPE Nimble Storage
Discussions
Discussions
Discussions
Forums
Discussions
Discussion Boards
Discussion Boards
Discussion Boards
Discussion Boards
- BladeSystem Infrastructure and Application Solutions
- Appliance Servers
- Alpha Servers
- BackOffice Products
- Internet Products
- HPE 9000 and HPE e3000 Servers
- Networking
- Netservers
- Secure OS Software for Linux
- Server Management (Insight Manager 7)
- Windows Server 2003
- Operating System - Tru64 Unix
- ProLiant Deployment and Provisioning
- Linux-Based Community / Regional
- Microsoft System Center Integration
Discussion Boards
Discussion Boards
Discussion Boards
Discussion Boards
Discussion Boards
Discussion Boards
Discussion Boards
Discussion Boards
Discussion Boards
Discussion Boards
Discussion Boards
Discussion Boards
Discussion Boards
Discussion Boards
Discussion Boards
Discussion Boards
Discussion Boards
Discussion Boards
Discussion Boards
Community
Resources
Forums
Blogs
- Subscribe to RSS Feed
- Mark Topic as New
- Mark Topic as Read
- Float this Topic for Current User
- Bookmark
- Subscribe
- Printer Friendly Page
- Mark as New
- Bookmark
- Subscribe
- Mute
- Subscribe to RSS Feed
- Permalink
- Report Inappropriate Content
10-13-2011 11:45 PM
10-13-2011 11:45 PM
no ip routing hp 2910
I have a procurve hp 2910
My configuration is this
; J9145A Configuration Editor; Created on release #W.14.49
hostname "amministrazione"
module 1 type J9145A
trunk 18,20 Trk1 LACP
ip default-gateway 192.168.0.107
ip routing
vlan 1
name "DEFAULT_VLAN"
untagged 1-13,15-17,19,21-24,Trk1
ip address 192.168.0.200 255.255.255.0
no untagged 14
exit
vlan 2
name "Vlan2"
untagged 14
ip address 192.168.30.200 255.255.255.0
exit
fault-finder bad-driver sensitivity high
fault-finder bad-transceiver sensitivity high
fault-finder bad-cable sensitivity high
fault-finder too-long-cable sensitivity high
fault-finder over-bandwidth sensitivity high
fault-finder broadcast-storm sensitivity high
fault-finder loss-of-link sensitivity high
fault-finder duplex-mismatch-HDx sensitivity high
fault-finder duplex-mismatch-FDx sensitivity high
console baud-rate 9600
router rip
exit
snmp-server community "public" unrestricted
spanning-tree Trk1 priority 4
amministrazione# show ip route
IP Route Entries
Destination Gateway VLAN Type Sub-Type Metric Dist.
------------------ --------------- ---- --------- ---------- ---------- -----
127.0.0.0/8 reject static 0 0
127.0.0.1/32 lo0 connected 1 0
192.168.0.0/24 DEFAULT_VLAN 1 connected 1 0
192.168.30.0/24 Vlan2 2 connected 1 0
but i'm not ping from inter-vlan
Thank's all
- Mark as New
- Bookmark
- Subscribe
- Mute
- Subscribe to RSS Feed
- Permalink
- Report Inappropriate Content
10-16-2011 01:50 PM
10-16-2011 01:50 PM
Re: no ip routing hp 2910
check default gateway client
vlan 1 member pc default gateway address must be 192.168.0.200
vlan 2 member pc default gateway address must be 192.168.30.200
disable windows firewall each pc
end disable ip default-gateway command on switch with
no ip default-gateway 192.168.0.107 command