Communications and Wireless
1748227 Members
4511 Online
108759 Solutions
New Discussion

Re: WX1200 with 7760AP.

 
wirawat
Occasional Visitor

WX1200 with 7760AP.

Hi.

 

I have a HP WX1200 Wireless LAN Switch and 7 APs(2750) and then one of AP had fail.

I have bought a new AP(7760) to replace but I can't add new AP to WX1200 because I can't find a managed firmware for upgrade a AP to managed mode.

 

Please advice can I find a managed firmware for upgrade 7760AP or another way for solve the problem.

(Sorry for my english.)

 

WX1200 Version 7.0.5.6.0

AP:      3CRWE776075 - HP 7760 Single Radio 802.11a/b/g Access Point
FW:     7760_1.6.45_WW

 

Thank in advance.

Wirawat. 

4 REPLIES 4
FlodNar
New Member

Re: WX1200 with 7760AP.

Have you set the 7760 to managed mode on the internal webpage? I only have 8760's running, but first I have to set country. After that I can choose Administration menu. Almost at the bottom of that page you can set the AP to managed mode. After a reset (just below managed mode setting) you can pick up the AP in the controller.

Ergonomidesign
New Member

Re: WX1200 with 7760AP.


Hello, we are in the same seat, and we are wondering if you managed to solve the problem with the wx1200 together with the AP7760..

 

//Robert

Techno
Regular Advisor

Re: WX1200 with 7760AP.

 

2 things you must do

 

1- Update the 7760 to the website version of firmware

2- Modify the 7760 to managed mode before trying to discover it.

 

Also make sure your controller is on the latest software version.

 

Good luck

The Tech Man Has Spoken....
gerry_iec
Occasional Advisor

Re: WX1200 with 7760AP.

I have tried to install ap7760 but it is not recognized by the wireless switch wx1200, but i was using ap2750 as a model into the configuration of wx1200 because model 7760 is not in the list of supported models

 

see this

 

WX1200# set ap 11 serial-id 9TZ4D9RD13380 model ap7760
^
Unrecognized command: set ap 11 serial-id 9TZ4D9RD13380 model ap7760
WX1200# set ap 11 serial-id 9TZ4D9RD13380 model ?
<ap_type> Choice of: AP-EASYA, AP2750, AP3150, AP3750, AP3850, AP3950, AP7250, AP8250, AP8750, MP-371, MP-371B, MP-372, MP-372-JP, MP-372A, MP-372B, MP-422, MP-422A, MP-422B, MP-422F, MP-422FB, MP-432, MP-620, MP-620A, MP-620B, MP-622, MP-632, MP-632F, MP-82

 

using 2750 as a model

 

WX1200# set ap 11 serial-id 9TZ4D9RD13380 model AP2750
success: change accepted.

*WX1200# set ap 11 radio 1 radio-profile corporativo mode enable
success: change accepted.

 

WX1200# disp ap status all
Flags: o = operational[10], c = configure[0], d = download[0], b = boot[0]
x = down[1]
a = auto AP, m = mesh AP, p/P = mesh portal (ena/actv), r = redundant[0]
i = insecure, e = encrypted, u = unencrypted
Radio: E = enabled - 20MHz channel, S = sentry
W/w = enabled - 40MHz wide channel (HTplus/HTminus)
D = admin disabled
IP Address: * = AP behind NAT
AP Flag IP Address Model MAC Address Radio 1 Radio 2 Uptime
---- ---- --------------- ------------ ----------------- ------- ------- ------
1 o--u Port 1 AP2750 00:18:6e:95:4a:c0 E 1/10 D ?/? 24d06h
2 o--u Port 2 AP2750 00:1a:c1:7d:0e:c0 E 11/18 D ?/? 10d07h
3 o--u Port 3 AP2750 00:14:7c:a5:1b:c0 E 11/18 D ?/? 24d06h
4 o--u Port 4 AP2750 00:1c:c5:90:0f:00 E 1/1 D ?/? 06d09h
5 o--u Port 5 AP2750 00:1a:c1:88:96:40 E 6/10 D ?/? 24d06h
6 o--u Port 6 AP2750 00:1c:c5:8f:f8:80 E 6/8 D ?/? 02d17h
7 o--i 10.1.102.222 AP2750 00:1c:c5:90:21:40 E 6/18 D ?/? 24d06h
8 o--i 10.1.102.72 AP2750 00:14:7c:a9:ce:00 E 1/4 D ?/? 24d06h
9 o--i 10.1.100.37 AP2750 00:1c:c5:90:29:00 E 11/18 D ?/? 24d06h
10 o--i 10.1.100.22 AP2750 00:24:73:59:f0:00 E 11/18 D ?/? 24d06h
11 x--- AP2750

 

its flag say x-- whats mean? i dont know documentation not say nothing about that status.

 

AP7760 version: 1.6.45_WW

wireless switch version: 7.0.13.3.0

 

best regards!