- Community Home
- >
- Networking
- >
- Wireless
- >
- M and MSM Series
- >
- Re: 3CRWDR300A-73, WPA problem
Categories
Company
Local Language
Forums
Discussions
Forums
- Data Protection and Retention
- Entry Storage Systems
- Legacy
- Midrange and Enterprise Storage
- Storage Networking
- HPE Nimble Storage
Discussions
Discussions
Discussions
Forums
Forums
Discussions
Discussion Boards
Discussion Boards
Discussion Boards
Discussion Boards
- BladeSystem Infrastructure and Application Solutions
- Appliance Servers
- Alpha Servers
- BackOffice Products
- Internet Products
- HPE 9000 and HPE e3000 Servers
- Networking
- Netservers
- Secure OS Software for Linux
- Server Management (Insight Manager 7)
- Windows Server 2003
- Operating System - Tru64 Unix
- ProLiant Deployment and Provisioning
- Linux-Based Community / Regional
- Microsoft System Center Integration
Discussion Boards
Discussion Boards
Discussion Boards
Discussion Boards
Discussion Boards
Discussion Boards
Discussion Boards
Discussion Boards
Discussion Boards
Discussion Boards
Discussion Boards
Discussion Boards
Discussion Boards
Discussion Boards
Discussion Boards
Discussion Boards
Discussion Boards
Discussion Boards
Discussion Boards
Discussion Boards
Discussion Boards
Discussion Boards
Community
Resources
Forums
Blogs
- Subscribe to RSS Feed
- Mark Topic as New
- Mark Topic as Read
- Float this Topic for Current User
- Bookmark
- Subscribe
- Printer Friendly Page
- Mark as New
- Bookmark
- Subscribe
- Mute
- Subscribe to RSS Feed
- Permalink
- Report Inappropriate Content
ā10-20-2009 04:58 AM
ā10-20-2009 04:58 AM
3CRWDR300A-73, WPA problem
iwconfig reports invalid crypt
eth1 IEEE 802.11g ESSID:"BLNL"
Mode:Managed Frequency:2.462 GHz Access Point: 00:22:57:1F:A6:F1
Bit Rate:54 Mb/s Tx-Power=20 dBm Sensitivity=8/0
Retry limit:7 RTS thr:off Fragment thr:off
Encryption key:XXXX-XXXX-XXXX-XXXX-XXXX-XXXX-XXXX-XXXX Security mode:open
Power Management:off
Link Quality=95/100 Signal level=-31 dBm Noise level=-86 dBm
Rx invalid nwid:0 Rx invalid crypt:111 Rx invalid frag:0
Tx excessive retries:0 Invalid misc:0 Missed beacon:2
What settings are recommended for WPA encryption?
By the way there are no problems with WEP encryption, or with NO encryption. Only WPA does not work.
I also tried upgrading to the latest firmware and resetting to the factory settings. It did not help.
This message was edited by blnl on 10-20-09 @ 3:36 PM
- Mark as New
- Bookmark
- Subscribe
- Mute
- Subscribe to RSS Feed
- Permalink
- Report Inappropriate Content
ā04-07-2010 01:27 PM
ā04-07-2010 01:27 PM
Re: 3CRWDR300A-73, WPA problem
Hello,
it seems that i have the same problem with a vony vaio (wifi chipset Atheros ar9285).
It works with no authentication or without encryption, however, with WPA it only connects ocasionally
Āæhave you solved the problem?
- Mark as New
- Bookmark
- Subscribe
- Mute
- Subscribe to RSS Feed
- Permalink
- Report Inappropriate Content
ā04-08-2010 04:14 PM
ā04-08-2010 04:14 PM
Re: 3CRWDR300A-73, WPA problem
No the problem is not solved. I downgraded the security to WEP.
I also contacted 3Com support about this issue. This is their answer:
"We don't support the Linux configuration, so we wouldn't be able to help in configuring Linux. The advise we can provide is to check if you are trying to use WPA and not WPA2, which is a newer standard of encryption his Linux device may have been using. Other than that, if you would like to talk to an engineer, we can only offer the chargeable one-off technical support option, we are talking about the connection issue with a non 3Com device that could imply that you would have to send us your Linux device to us to test it."
This message was edited by blnl on 4-8-10 @ 4:15 PM