M and MSM Series
cancel
Showing results for 
Search instead for 
Did you mean: 

M200 Firmware problem

 
Highlighted
Occasional Visitor

M200 Firmware problem

Hi,

I have a HP M200 AP that doesn’t completely boot, continuously blinking the status led.

When I put it in recovery mode a send the public available firmware for download via tftp it says "Image validation failed: bad magic". Does anyone have a recovery firmware (from the MSM series something like xxx.cim.startup)?

I also have access to the uart port, so if anyone knows how to use the the public available firmware for download via u-boot please share. Thank you.

 Best Regards

Boot 16.1 (Jun 17 2010 - 11:16:04)

PABST M210
DRAM:
sri . . 64 MB
Top of RAM usable for U-Boot at: 84000000
Reserving 291k for U-Boot at: 83fb4000
Reserving 584k for malloc() at: 83f22000
Reserving 404 Bytes for Board Info at: 83f21e6c
Reserving 36 Bytes for Global Data at: 83f21e48
Reserving 128k for boot params() at: 83f01e48
Stack Pointer at: 83f01e28
Now running in RAM - U-Boot at: 83fb4000
Flash manuf 01, device 227e 2222 2201
Flash start be000000, end c0000000
Flash blocks_size 20000, blocks 100
Flash: 32 MB
*** Warning - bad CRC, using default environment

In:    serial
Out:   serial
Err:   serial
pabst GPIO debug:
Deault GPIO OE=195c8
Deault GPIO INPUT=266f7b
Deault GPIO OUT=548
Deault GPIO SET=548
Deault GPIO CLEAR=548
Deault GPIO INT=200000
Deault GPIO INT_TYPE=0
Deault GPIO INT_PENDING=0
Deault GPIO INT_MASK=200000
hw_flag=80000001, sys_clk=0
ag7100_enet_initialize...
AG7100 phy setup ....
========>  Dump all phyaddr Chip and Vendor Value <========
MAC[eth0]  read phy phyaddr=00 Reg#2 Value=0x0141
MAC[eth0]  read phy phyaddr=00 Reg#3 Value=0x0e90
-------------------------------------------------------------

---> madInit start
Pre-Initialization is done for the device 0x29.
---> madInit finished
ag7100 MAC[0] eth0: 98:4b:e1:f6:60:f5
eth0 up


Trying eth0
dup 1 duplex=1 speed 1
dup 0 speed 1
: unit 0 phy is up... 100Mbps half duplex
ag7100_set_mac_from_link==============> speed=1 duplex=0
: pll reg 0x18050014: 0x13000a44  : cfg_1: 0x7ff0000
: cfg_2: 0xfff
: cfg_3: 0x780008
: cfg_4: 0x3ffff
: cfg_5: 0x3ffff
: done cfg2 0x7114 ifctl 0x10000 miictrl 0x12
eth0 configured
checking for reset button... : not pressed
MISR         = 00000001
MIMR         = 00000000
GISR         = 00000020
GPIO INT     = 00200000
GPIO MASK    = 00200000
GPIO OUT     = 00000400
GPIO PENDING = 00000000
Kernel arg: 'ro'
## BID copied to ram at 0x83f47380
## Trying to boot Linux kernel from flash block 0...
## Booting image at 80200000 ...
   Image Name:   5.4.1.1-01-1141
   Created:      2012-05-10   0:50:24 UTC
   Image Type:   MIPS Linux Kernel Image (gzip compressed)
   Data Size:    782790 Bytes = 764.4 kB
   Load Address: 80002000
   Entry Point:  80002000
   Initrd Size:  0 Bytes
## Verifying Checksum ... OK
## Uncompressing Kernel Image ... Inflated to 1843200 bytes OK
## Kernel args:
   0:  linux
   1:  mem=64M
## Kernel env:
   memsize=67108864
   initrd_start=0x00000000
   initrd_size=0x0
   flash_start=0xBE000000
   flash_size=0x2000000
   bootinfo=0x83F21E6C
## Transferring control to Linux (at address 80002000) ...
###############################################################
memsize: 67108864
CPU revision is: 00019374
Primary instruction cache 64kB, physically tagged, 4-way, linesize 32 bytes.
Primary data cache 32kB, 4-way, linesize 32 bytes.
Linux version 2.4.36.6-******** (constructor@mobrd-server) (gcc version 3.4.4) #1 Wed May 9 20:49:58 EDT 2012
detect REV_ID_MAJOR_AR913X
detect AR91XX_REV_ID_MINOR_AR9132
Atheros AR9132 rev 2<1>Register early_printk
pabst platform
Atheros AR9132 rev 2, CPU:400.000 MHz, AHB:200.000 MHz, DDR:400.000 MHz
Determined physical RAM map:
 memory: 04000000 @ 00000000 (usable)
User-defined physical RAM map:
 memory: 04000000 @ 00000000 (usable)
On node 0 totalpages: 16384
zone(0): 16384 pages.
zone (0) min 128, low 384, high 512
zone(1): 0 pages.
zone(2): 0 pages.
Kernel command line: mem=64M
Using 200.000 MHz high precision timer.
Calibrating delay loop... 266.24 BogoMIPS
Memory: 62732k/65536k available (1600k kernel code, 2804k reserved, 92k data, 84k init, 0k highmem)
Dentry cache hash table entries: 8192 (order: 4, 65536 bytes)
Inode cache hash table entries: 4096 (order: 3, 32768 bytes)
Mount cache hash table entries: 512 (order: 0, 4096 bytes)
Buffer cache hash table entries: 4096 (order: 2, 16384 bytes)
Page-cache hash table entries: 16384 (order: 4, 65536 bytes)
Checking for 'wait' instruction...  available.
POSIX conformance testing by UNIFIX
pabst_init
^^
Linux NET4.0 for Linux 2.4
Based upon Swansea University Computer Society NET3.039
Initializing RT netlink socket
Starting kswapd
Squashfs 2.2-r2 (released 2005/09/08) (C) 2002-2005 Phillip Lougher
JFFS version 1.0, (C) 1999, 2000  Axis Communications AB
pty: 256 Unix98 ptys configured
ttyS00 at 0xb8020003 (irq = 19) is a 16550Ath no serial options enabled
Software Watchdog Timer: 0.05, timer margin: 60 sec
RAMDISK driver initialized: 16 RAM disks of 16384K size 1024 blocksize
loop: loaded (max 8 devices)
imq driver loaded.
Crypto engine S/W registered as #4
NET4: Linux TCP/IP 1.0 for NET4.0
IP Protocols: ICMP, UDP, TCP, IGMP
IP: routing cache hash table of 512 buckets, 4Kbytes
TCP: Hash tables configured (established 4096 bind 8192)
Linux IP multicast router 0.06 plus PIM-SM
UDP tunneling driver
ip_conntrack version 2.1 (4096 buckets, 32768 max) - 352 bytes per conntrack
ip_tables: (C) 2000-2002 Netfilter core team
NET4: Unix domain sockets 1.0/SMP for Linux NET4.0.
NET4: Ethernet Bridge 008 for NET4.0
Bridge firewalling registered
802.1Q VLAN Support v1.8 Ben Greear <greearb@candelatech.com>
All bugs added by David S. Miller <davem@redhat.com>
Flash manuf 01, device 227e 2222 2201
Flash: Flash start be000000, end c0000000
Flash: Flash blocks_size 20000, blocks 100
VFS: Mounted root (squashfs filesystem) readonly.
run_init_process ...
Algorithmics/MIPS FPU Emulator v1.5
init started:  BusyBox v1.00-pre4 (2012.05.10-01:00+0000) multi-call binary
Starting pid 10, console /dev/console: '/bin/ash'
Mon Jan  1 00:00:00 UTC 2001
mount: Mounting /proc on /proc failed: Device or resource busy
-----> Flash mounted file system
Key 31 not found.
10+0 records in
10+0 records out
Mount succeeded 0
Using /lib/modules/2.4.36.6-colubris/kernel/drivers/net/pppox_tty.o
Registering PPPoX driver
PPPoX: PPPoE
PPPoX: GRE
Crypto engine FIPS registered as #3
Using /lib/modules/2.4.36.6-colubris/kernel/drivers/net/slhc.o
CSLIP: code copyright 1989 Regents of the University of California
Using /lib/modules/2.4.36.6-colubris/kernel/drivers/net/ppp.o
PPP: version 2.3.11 (demand dialling)
PPP line discipline registered.
Err: -3
Badness in sqlzma_un at uncomp.c:138
This architecture does not implement dump_stack()
monitord: relocation error: monitord: symbol errno_location, version GLIBC_2.0 not defined in file libc.so.6 with link time reference
Starting pid 178, console /dev/console: '/bin/keypress'
Press <enter> to start console. You have 30 seconds.

1 REPLY 1
Occasional Visitor

Re: M200 Firmware problem

Hi,

I have HP V-M200 that booting, getting an ip address, but I can't access to the device. Only can ping.

So I also have access to the uart port, so if anyone knows how to use the the public available firmware for download via u-boot please share. Thank you.

Regards

Vardges Tagesyan

Boot 16.1 (Jun 17 2010 - 11:16:04)

PABST M210
DRAM:
sri . . 64 MB
Top of RAM usable for U-Boot at: 84000000
Reserving 291k for U-Boot at: 83fb4000
Reserving 584k for malloc() at: 83f22000
Reserving 404 Bytes for Board Info at: 83f21e6c
Reserving 36 Bytes for Global Data at: 83f21e48
Reserving 128k for boot params() at: 83f01e48
Stack Pointer at: 83f01e28
Now running in RAM - U-Boot at: 83fb4000
Flash manuf 01, device 227e 2222 2201
Flash start be000000, end c0000000
Flash blocks_size 20000, blocks 100
Flash: 32 MB
*** Warning - bad CRC, using default environment

In: serial
Out: serial
Err: serial
pabst GPIO debug:
Deault GPIO OE=195c8
Deault GPIO INPUT=266f7b
Deault GPIO OUT=548
Deault GPIO SET=548
Deault GPIO CLEAR=548
Deault GPIO INT=200000
Deault GPIO INT_TYPE=0
Deault GPIO INT_PENDING=0
Deault GPIO INT_MASK=200000
hw_flag=80000001, sys_clk=-1
ag7100_enet_initialize...
AG7100 phy setup ....
========> Dump all phyaddr Chip and Vendor Value <========
MAC[eth0] read phy phyaddr=00 Reg#2 Value=0x0141
MAC[eth0] read phy phyaddr=00 Reg#3 Value=0x0e90
-------------------------------------------------------------

---> madInit start
Pre-Initialization is done for the device 0x29.
---> madInit finished
ag7100 MAC[0] eth0: 2c:41:38:28:95:cd
eth0 up


Trying eth0
dup 1 duplex=1 speed 1
dup 0 speed 1
: unit 0 phy is up... 100Mbps half duplex
ag7100_set_mac_from_link==============> speed=1 duplex=0
: pll reg 0x18050014: 0x13000a44 : cfg_1: 0x7ff0000
: cfg_2: 0xfff
: cfg_3: 0x780008
: cfg_4: 0x3ffff
: cfg_5: 0x3ffff
: done cfg2 0x7114 ifctl 0x10000 miictrl 0x12
eth0 configured
checking for reset button... : not pressed
MISR = 00000001
MIMR = 00000000
GISR = 00000020
GPIO INT = 00200000
GPIO MASK = 00200000
GPIO OUT = 00000400
GPIO PENDING = 00000000
Kernel arg: 'ro'
## BID copied to ram at 0x83f47380
## Trying to boot Linux kernel from flash block 0...
## Booting image at 80200000 ...
Image Name: 5.4.1.1-01-1648
Created: 2014-03-31 20:12:42 UTC
Image Type: MIPS Linux Kernel Image (gzip compressed)
Data Size: 782778 Bytes = 764.4 kB
Load Address: 80002000
Entry Point: 80002000
Initrd Size: 0 Bytes
## Verifying Checksum ... OK
## Uncompressing Kernel Image ... Inflated to 1843200 bytes OK
## Kernel args:
0: linux
1: mem=64M
## Kernel env:
memsize=67108864
initrd_start=0x00000000
initrd_size=0x0
flash_start=0xBE000000
flash_size=0x2000000
bootinfo=0x83F21E6C
## Transferring control to Linux (at address 80002000) ...
###############################################################
memsize: 67108864
CPU revision is: 00019374
Primary instruction cache 64kB, physically tagged, 4-way, linesize 32 bytes.
Primary data cache 32kB, 4-way, linesize 32 bytes.
Linux version 2.4.36.6-******** (ec@mobrd-builder-3) (gcc version 3.4.4) #1 Mon Mar 31 20:12:24 UTC 2014
detect REV_ID_MAJOR_AR913X
detect AR91XX_REV_ID_MINOR_AR9132
Atheros AR9132 rev 2<1>Register early_printk
pabst platform
Atheros AR9132 rev 2, CPU:400.000 MHz, AHB:200.000 MHz, DDR:400.000 MHz
Determined physical RAM map:
memory: 04000000 @ 00000000 (usable)
User-defined physical RAM map:
memory: 04000000 @ 00000000 (usable)
On node 0 totalpages: 16384
zone(0): 16384 pages.
zone (0) min 128, low 384, high 512
zone(1): 0 pages.
zone(2): 0 pages.
Kernel command line: mem=64M
Using 200.000 MHz high precision timer.
Calibrating delay loop... 266.24 BogoMIPS
Memory: 62732k/65536k available (1600k kernel code, 2804k reserved, 92k data, 84k init, 0k highmem)
Dentry cache hash table entries: 8192 (order: 4, 65536 bytes)
Inode cache hash table entries: 4096 (order: 3, 32768 bytes)
Mount cache hash table entries: 512 (order: 0, 4096 bytes)
Buffer cache hash table entries: 4096 (order: 2, 16384 bytes)
Page-cache hash table entries: 16384 (order: 4, 65536 bytes)
Checking for 'wait' instruction... available.
POSIX conformance testing by UNIFIX
pabst_init
^^
Linux NET4.0 for Linux 2.4
Based upon Swansea University Computer Society NET3.039
Initializing RT netlink socket
Starting kswapd
Squashfs 2.2-r2 (released 2005/09/08) (C) 2002-2005 Phillip Lougher
JFFS version 1.0, (C) 1999, 2000 Axis Communications AB
pty: 256 Unix98 ptys configured
ttyS00 at 0xb8020003 (irq = 19) is a 16550Ath no serial options enabled
Software Watchdog Timer: 0.05, timer margin: 60 sec
RAMDISK driver initialized: 16 RAM disks of 16384K size 1024 blocksize
loop: loaded (max 8 devices)
imq driver loaded.
Crypto engine S/W registered as #4
NET4: Linux TCP/IP 1.0 for NET4.0
IP Protocols: ICMP, UDP, TCP, IGMP
IP: routing cache hash table of 512 buckets, 4Kbytes
TCP: Hash tables configured (established 4096 bind 8192)
Linux IP multicast router 0.06 plus PIM-SM
UDP tunneling driver
ip_conntrack version 2.1 (4096 buckets, 32768 max) - 352 bytes per conntrack
ip_tables: (C) 2000-2002 Netfilter core team
NET4: Unix domain sockets 1.0/SMP for Linux NET4.0.
NET4: Ethernet Bridge 008 for NET4.0
Bridge firewalling registered
802.1Q VLAN Support v1.8 Ben Greear <greearb@candelatech.com>
All bugs added by David S. Miller <davem@redhat.com>
Flash manuf 01, device 227e 2222 2201
Flash: Flash start be000000, end c0000000
Flash: Flash blocks_size 20000, blocks 100
VFS: Mounted root (squashfs filesystem) readonly.
run_init_process ...
Algorithmics/MIPS FPU Emulator v1.5
init started: BusyBox v1.00-pre4 (2014.03.31-20:21+0000) multi-call binary
Starting pid 10, console /dev/console: '/bin/ash'
Mon Jan 1 00:00:00 UTC 2001
mount: Mounting /proc on /proc failed: Device or resource busy
-----> Flash mounted file system
Key 31 not found.
10+0 records in
10+0 records out
Mount succeeded 0
Using /lib/modules/2.4.36.6-colubris/kernel/drivers/net/pppox_tty.o
Registering PPPoX driver
PPPoX: PPPoE
PPPoX: GRE
Crypto engine FIPS registered as #3
Using /lib/modules/2.4.36.6-colubris/kernel/drivers/net/slhc.o
CSLIP: code copyright 1989 Regents of the University of California
Using /lib/modules/2.4.36.6-colubris/kernel/drivers/net/ppp.o
PPP: version 2.3.11 (demand dialling)
PPP line discipline registered.
cp: /ram/tmp/rpc.log: No such file or directory
Starting pid 186, console /dev/console: '/bin/keypress'
Press <enter> to start console. You have 30 seconds.
wlan: 0.7.1.1
Initializing WDS support
ath_hal: 0.9.17.1 (AR5212, AR5416, RF5111, RF5112, RF2413, RF5413, RF2316, RF2317, PRIVATE_DIAG)
ath_dfs: Version 2.0.0
Copyright (c) 2005-2006 Atheros Communications, Inc. All Rights Reserved
ath_rate_atheros: Copyright (c) 2001-2005 Atheros Communications, Inc, All Rights Reserved
ath_lbus: 0.8.3.2
Howl Revision ID 0xb9 <7>wvlan0: mac 20.0 phy 10.2<6> 5ghz radio 12.0
wvlan0: Atheros AR9100 WiSoC: mem=0xb80c0000, irq=2
wvlan0: 802.11 address: 00:9c:02:65:7a:94 mask fc, 4 addresses
device wvlan0 entered promiscuous mode
Pre-Initialization is done for the device 0x29.
Writing 4
device eth0 entered promiscuous mode
pvw0.1-4094: dev_set_promiscuity(master, 1)
device pvw0 entered promiscuous mode
device pvw0.1-4094 entered promiscuous mode
Err: -5
Badness in sqlzma_un at uncomp.c:138
This architecture does not implement dump_stack()
Err: -3
Badness in sqlzma_un at uncomp.c:138
This architecture does not implement dump_stack()
SQUASHFS error: Unable to read page, block 72b522, size 5b98
Err: -3
Badness in sqlzma_un at uncomp.c:138
This architecture does not implement dump_stack()
SQUASHFS error: Unable to read page, block 72b522, size 5b98
Err: -3
Badness in sqlzma_un at uncomp.c:138
This architecture does not implement dump_stack()
SQUASHFS error: Unable to read page, block 72b522, size 5b98
Err: -3
Badness in sqlzma_un at uncomp.c:138
This architecture does not implement dump_stack()
SQUASHFS error: Unable to read page, block 72b522, size 5b98
Err: -3
Badness in sqlzma_un at uncomp.c:138
This architecture does not implement dump_stack()
SQUASHFS error: Unable to read page, block 72b522, size 5b98
Err: -3
Badness in sqlzma_un at uncomp.c:138
This architecture does not implement dump_stack()
SQUASHFS error: Unable to read page, block 72b522, size 5b98
Err: -3
Badness in sqlzma_un at uncomp.c:138
This architecture does not implement dump_stack()
SQUASHFS error: Unable to read page, block 72b522, size 5b98
Err: -3
Badness in sqlzma_un at uncomp.c:138
This architecture does not implement dump_stack()
SQUASHFS error: Unable to read page, block 72b522, size 5b98
Err: -3
Badness in sqlzma_un at uncomp.c:138
This architecture does not implement dump_stack()
SQUASHFS error: Unable to read page, block 7310ba, size 5cd7
Err: -3
Badness in sqlzma_un at uncomp.c:138
This architecture does not implement dump_stack()
SQUASHFS error: Unable to read page, block 7310ba, size 5cd7
Err: -3
Badness in sqlzma_un at uncomp.c:138
This architecture does not implement dump_stack()
SQUASHFS error: Unable to read page, block 7310ba, size 5cd7
Err: -3
Badness in sqlzma_un at uncomp.c:138
This architecture does not implement dump_stack()
SQUASHFS error: Unable to read page, block 7310ba, size 5cd7
Err: -3
Badness in sqlzma_un at uncomp.c:138
This architecture does not implement dump_stack()
SQUASHFS error: Unable to read page, block 7310ba, size 5cd7
Err: -3
Badness in sqlzma_un at uncomp.c:138
This architecture does not implement dump_stack()
SQUASHFS error: Unable to read page, block 7310ba, size 5cd7
Err: -3
Badness in sqlzma_un at uncomp.c:138
This architecture does not implement dump_stack()
SQUASHFS error: Unable to read page, block 7310ba, size 5cd7
Err: -3
Badness in sqlzma_un at uncomp.c:138
This architecture does not implement dump_stack()
SQUASHFS error: Unable to read page, block 7310ba, size 5cd7
Err: -3
Badness in sqlzma_un at uncomp.c:138
This architecture does not implement dump_stack()
SQUASHFS error: Unable to read page, block 7310ba, size 5cd7
Err: -3
Badness in sqlzma_un at uncomp.c:138
This architecture does not implement dump_stack()
SQUASHFS error: Unable to read page, block 7310ba, size 5cd7
Err: -3
Badness in sqlzma_un at uncomp.c:138
This architecture does not implement dump_stack()
SQUASHFS error: Unable to read page, block 7310ba, size 5cd7
Err: -3
Badness in sqlzma_un at uncomp.c:138
This architecture does not implement dump_stack()
SQUASHFS error: Unable to read page, block 7310ba, size 5cd7
Err: -3
Badness in sqlzma_un at uncomp.c:138
This architecture does not implement dump_stack()
SQUASHFS error: Unable to read page, block 7310ba, size 5cd7
Err: -3
Badness in sqlzma_un at uncomp.c:138
This architecture does not implement dump_stack()
SQUASHFS error: Unable to read page, block 7310ba, size 5cd7
Err: -3
Badness in sqlzma_un at uncomp.c:138
This architecture does not implement dump_stack()
SQUASHFS error: Unable to read page, block 7310ba, size 5cd7
Err: -3
Badness in sqlzma_un at uncomp.c:138
This architecture does not implement dump_stack()
SQUASHFS error: Unable to read page, block 7310ba, size 5cd7
Err: -3
Badness in sqlzma_un at uncomp.c:138
This architecture does not implement dump_stack()
SQUASHFS error: Unable to read page, block 736d91, size 5381
Err: -3
Badness in sqlzma_un at uncomp.c:138
This architecture does not implement dump_stack()
SQUASHFS error: Unable to read page, block 736d91, size 5381
Err: -3
Badness in sqlzma_un at uncomp.c:138
This architecture does not implement dump_stack()
SQUASHFS error: Unable to read page, block 736d91, size 5381
Err: -3
Badness in sqlzma_un at uncomp.c:138
This architecture does not implement dump_stack()
SQUASHFS error: Unable to read page, block 736d91, size 5381
Err: -3
Badness in sqlzma_un at uncomp.c:138
This architecture does not implement dump_stack()
SQUASHFS error: Unable to read page, block 736d91, size 5381
Err: -3
Badness in sqlzma_un at uncomp.c:138
This architecture does not implement dump_stack()
SQUASHFS error: Unable to read page, block 736d91, size 5381
Err: -3
Badness in sqlzma_un at uncomp.c:138
This architecture does not implement dump_stack()
SQUASHFS error: Unable to read page, block 736d91, size 5381
Err: -3
Badness in sqlzma_un at uncomp.c:138
This architecture does not implement dump_stack()
SQUASHFS error: Unable to read page, block 736d91, size 5381
Err: -3
Badness in sqlzma_un at uncomp.c:138
This architecture does not implement dump_stack()
SQUASHFS error: Unable to read page, block 736d91, size 5381
Err: -3
Badness in sqlzma_un at uncomp.c:138
This architecture does not implement dump_stack()
SQUASHFS error: Unable to read page, block 736d91, size 5381
Err: -3
Badness in sqlzma_un at uncomp.c:138
This architecture does not implement dump_stack()
SQUASHFS error: Unable to read page, block 736d91, size 5381
Err: -3
Badness in sqlzma_un at uncomp.c:138
This architecture does not implement dump_stack()
SQUASHFS error: Unable to read page, block 736d91, size 5381
Err: -3
Badness in sqlzma_un at uncomp.c:138
This architecture does not implement dump_stack()
SQUASHFS error: Unable to read page, block 736d91, size 5381
Err: -3
Badness in sqlzma_un at uncomp.c:138
This architecture does not implement dump_stack()
SQUASHFS error: Unable to read page, block 736d91, size 5381
Err: -3
Badness in sqlzma_un at uncomp.c:138
This architecture does not implement dump_stack()
SQUASHFS error: Unable to read page, block 736d91, size 5381
Err: -3
Badness in sqlzma_un at uncomp.c:138
This architecture does not implement dump_stack()
SQUASHFS error: Unable to read page, block 736d91, size 5381
Err: -3
Badness in sqlzma_un at uncomp.c:138
This architecture does not implement dump_stack()
SQUASHFS error: Unable to read page, block 73c112, size 62ae
Err: -3
Badness in sqlzma_un at uncomp.c:138
This architecture does not implement dump_stack()
SQUASHFS error: Unable to read page, block 73c112, size 62ae
Err: -3
Badness in sqlzma_un at uncomp.c:138
This architecture does not implement dump_stack()
SQUASHFS error: Unable to read page, block 73c112, size 62ae
Err: -3
Badness in sqlzma_un at uncomp.c:138
This architecture does not implement dump_stack()
SQUASHFS error: Unable to read page, block 73c112, size 62ae
Err: -3
Badness in sqlzma_un at uncomp.c:138
This architecture does not implement dump_stack()
SQUASHFS error: Unable to read page, block 73c112, size 62ae
Err: -3
Badness in sqlzma_un at uncomp.c:138
This architecture does not implement dump_stack()
SQUASHFS error: Unable to read page, block 73c112, size 62ae
Err: -3
Badness in sqlzma_un at uncomp.c:138
This architecture does not implement dump_stack()
SQUASHFS error: Unable to read page, block 73c112, size 62ae
Err: -3
Badness in sqlzma_un at uncomp.c:138
This architecture does not implement dump_stack()
SQUASHFS error: Unable to read page, block 73c112, size 62ae
Err: -3
Badness in sqlzma_un at uncomp.c:138
This architecture does not implement dump_stack()
SQUASHFS error: Unable to read page, block 73c112, size 62ae
Err: -3
Badness in sqlzma_un at uncomp.c:138
This architecture does not implement dump_stack()
SQUASHFS error: Unable to read page, block 73c112, size 62ae
Err: -3
Badness in sqlzma_un at uncomp.c:138
This architecture does not implement dump_stack()
SQUASHFS error: Unable to read page, block 73c112, size 62ae
Err: -3
Badness in sqlzma_un at uncomp.c:138
This architecture does not implement dump_stack()
SQUASHFS error: Unable to read page, block 73c112, size 62ae
Err: -3
Badness in sqlzma_un at uncomp.c:138
This architecture does not implement dump_stack()
SQUASHFS error: Unable to read page, block 73c112, size 62ae
Err: -3
Badness in sqlzma_un at uncomp.c:138
This architecture does not implement dump_stack()
SQUASHFS error: Unable to read page, block 73c112, size 62ae
Err: -3
Badness in sqlzma_un at uncomp.c:138
This architecture does not implement dump_stack()
SQUASHFS error: Unable to read page, block 73c112, size 62ae
Err: -3
Badness in sqlzma_un at uncomp.c:138
This architecture does not implement dump_stack()
SQUASHFS error: Unable to read page, block 73c112, size 62ae
keypress: Time is up
Channel 36:
Channel 40:
Channel 44:
Channel 48:
Channel 149:
Channel 153:
Channel 157:
Channel 161:
AutoChannelSelection: ifname=wvlan0, selecting best initial channel (36,-95dBm)