- Community Home
- >
- Networking
- >
- Wireless
- >
- M and MSM Series
- >
- Re: MSM430 Power Cycling
Categories
Company
Local Language
Forums
Discussions
Forums
- Data Protection and Retention
- Entry Storage Systems
- Legacy
- Midrange and Enterprise Storage
- Storage Networking
- HPE Nimble Storage
Discussions
Discussions
Discussions
Forums
Forums
Discussions
Discussion Boards
Discussion Boards
Discussion Boards
Discussion Boards
- BladeSystem Infrastructure and Application Solutions
- Appliance Servers
- Alpha Servers
- BackOffice Products
- Internet Products
- HPE 9000 and HPE e3000 Servers
- Networking
- Netservers
- Secure OS Software for Linux
- Server Management (Insight Manager 7)
- Windows Server 2003
- Operating System - Tru64 Unix
- ProLiant Deployment and Provisioning
- Linux-Based Community / Regional
- Microsoft System Center Integration
Discussion Boards
Discussion Boards
Discussion Boards
Discussion Boards
Discussion Boards
Discussion Boards
Discussion Boards
Discussion Boards
Discussion Boards
Discussion Boards
Discussion Boards
Discussion Boards
Discussion Boards
Discussion Boards
Discussion Boards
Discussion Boards
Discussion Boards
Discussion Boards
Discussion Boards
Discussion Boards
Discussion Boards
Discussion Boards
Community
Resources
Forums
Blogs
- Subscribe to RSS Feed
- Mark Topic as New
- Mark Topic as Read
- Float this Topic for Current User
- Bookmark
- Subscribe
- Printer Friendly Page
- Mark as New
- Bookmark
- Subscribe
- Mute
- Subscribe to RSS Feed
- Permalink
- Report Inappropriate Content
тАО12-11-2012 04:29 AM
тАО12-11-2012 04:29 AM
MSM430 Power Cycling
Hi,
We're trying to run 2 x MSM430 from a MSM750. Both have 5.5.3.0-01-10326 firmware and 5.5.3.0-01-10326 software on the controller.
We have about 15 WAPS deployed around the site. These are the only two MSM430's
They boot up, detected, configured, get clients and then after anywhere between 10 seconds to 4 minutes the unit power cycles.
All apears fine before they restart, then they just get stuck in this cycle.
Any ideas appreciated.
Dec 1 06:12:52 err eapolserver CN28DWZ8ZW Interface r1v3 doesn't exist Dec 1 06:12:52 err eapolserver CN28DWZ8ZW Interface r1v2 doesn't exist Dec 1 06:12:50 err rpcd CN28DWZ8ZW BRIDGE_add: BRCTL_ADD_BRIDGE returned -1 Dec 1 06:10:53 err eapolserver CN28DWZ8ZW Interface r1v3 doesn't exist Dec 1 06:10:47 err eapolserver CN28DWZ8ZW Interface r1v2 doesn't exist
- Mark as New
- Bookmark
- Subscribe
- Mute
- Subscribe to RSS Feed
- Permalink
- Report Inappropriate Content
тАО12-11-2012 01:31 PM
тАО12-11-2012 01:31 PM
Re: MSM430 Power Cycling
@AngryAdmin wrote:Hi,
We're trying to run 2 x MSM430 from a MSM750. Both have 5.5.3.0-01-10326 firmware and 5.5.3.0-01-10326 software on the controller.
We have about 15 WAPS deployed around the site. These are the only two MSM430's
They boot up, detected, configured, get clients and then after anywhere between 10 seconds to 4 minutes the unit power cycles.
All apears fine before they restart, then they just get stuck in this cycle.
Any ideas appreciated.
Dec 1 06:12:52 err eapolserver CN28DWZ8ZW Interface r1v3 doesn't exist Dec 1 06:12:52 err eapolserver CN28DWZ8ZW Interface r1v2 doesn't exist Dec 1 06:12:50 err rpcd CN28DWZ8ZW BRIDGE_add: BRCTL_ADD_BRIDGE returned -1 Dec 1 06:10:53 err eapolserver CN28DWZ8ZW Interface r1v3 doesn't exist Dec 1 06:10:47 err eapolserver CN28DWZ8ZW Interface r1v2 doesn't exist
There are several paths you could take to troubleshoot this.
1.) Call support and ask them if this is a known issue.
2.) Try the version 5.5.5 software that was just released and publically posted. Entitlement restrictions apply.
3.) The error looks very much like there is some confusion about a 3rd and 4th VSC configuration that is not being applied properly. You may want to factory reset your controller and the APs, let them all find each other again, and see if the rebooting of the APs stops (I think it will.) Then, reconfigure your setup from scratch and see if the problem re-occurs or does not.
--glen
- Mark as New
- Bookmark
- Subscribe
- Mute
- Subscribe to RSS Feed
- Permalink
- Report Inappropriate Content
тАО01-04-2013 02:54 AM
тАО01-04-2013 02:54 AM
Re: MSM430 Power Cycling
In Case of you didn't solve your problem
Excluding some channels(i my situation 36) for n solved my problem