- Community Home
- >
- Networking
- >
- Wireless
- >
- M and MSM Series
- >
- Network loops when using an access controlled VSC
Categories
Company
Local Language
Forums
Discussions
Forums
- Data Protection and Retention
- Entry Storage Systems
- Legacy
- Midrange and Enterprise Storage
- Storage Networking
- HPE Nimble Storage
Discussions
Discussions
Discussions
Forums
Discussions
Discussion Boards
Discussion Boards
Discussion Boards
Discussion Boards
- BladeSystem Infrastructure and Application Solutions
- Appliance Servers
- Alpha Servers
- BackOffice Products
- Internet Products
- HPE 9000 and HPE e3000 Servers
- Networking
- Netservers
- Secure OS Software for Linux
- Server Management (Insight Manager 7)
- Windows Server 2003
- Operating System - Tru64 Unix
- ProLiant Deployment and Provisioning
- Linux-Based Community / Regional
- Microsoft System Center Integration
Discussion Boards
Discussion Boards
Discussion Boards
Discussion Boards
Discussion Boards
Discussion Boards
Discussion Boards
Discussion Boards
Discussion Boards
Discussion Boards
Discussion Boards
Discussion Boards
Discussion Boards
Discussion Boards
Discussion Boards
Discussion Boards
Discussion Boards
Discussion Boards
Discussion Boards
Community
Resources
Forums
Blogs
- Subscribe to RSS Feed
- Mark Topic as New
- Mark Topic as Read
- Float this Topic for Current User
- Bookmark
- Subscribe
- Printer Friendly Page
- Mark as New
- Bookmark
- Subscribe
- Mute
- Subscribe to RSS Feed
- Permalink
- Report Inappropriate Content
06-18-2015 11:28 AM
06-18-2015 11:28 AM
Network loops when using an access controlled VSC
Hello,
We are having a strange issue where our controller LAN mac address will momentarily appear on the AP switch port. This will cause an address flap periodically throughout the day until our network becomes completely unstable.
We are on Version 6.5.1. This behavior didn't happen in version 5.x. Unfortunately, we cannot go back to 5.x as we need the bonjour features in 6.
Has anyone else seen this before? Below are the warnings from our Cisco switch.
4-Warning 6/1/2015 7:52 Host 2C:41:38:42:xx:xx in vlan 1 is flapping between port Gi1/2 and port Gi7/29
4-Warning 6/1/2015 7:56 Host 2C:41:38:42:xx:xx in vlan 1 is flapping between port Gi1/15 and port Gi7/29
4-Warning 6/1/2015 7:56 Host 2C:41:38:42:xx:xx in vlan 1 is flapping between port Gi1/3 and port Gi7/29
4-Warning 6/1/2015 8:02 Host 2C:41:38:42:xx:xx in vlan 1 is flapping between port Gi1/4 and port Gi7/29
4-Warning 6/1/2015 8:17 Host 2C:41:38:42:xx:xx in vlan 1 is flapping between port Gi2/26 and port Gi7/29
4-Warning 6/1/2015 8:18 Host 2C:41:38:42:xx:xx in vlan 1 is flapping between port Gi1/4 and port Gi7/29
4-Warning 6/1/2015 8:24 Host 2C:41:38:42:xx:xx in vlan 1 is flapping between port Gi1/5 and port Gi7/29
- Mark as New
- Bookmark
- Subscribe
- Mute
- Subscribe to RSS Feed
- Permalink
- Report Inappropriate Content
06-19-2015 04:18 AM
06-19-2015 04:18 AM
Re: Network loops when using an access controlled VSC
Hello,
Did you tried the 6.5.2.0 firmware ?
Regards,