- Community Home
- >
- Storage
- >
- Entry Storage Systems
- >
- MSA Storage
- >
- Re: CPQKGPSA
Categories
Company
Local Language
Forums
Discussions
Forums
- Data Protection and Retention
- Entry Storage Systems
- Legacy
- Midrange and Enterprise Storage
- Storage Networking
- HPE Nimble Storage
Discussions
Discussions
Discussions
Forums
Forums
Discussions
Discussion Boards
Discussion Boards
Discussion Boards
Discussion Boards
- BladeSystem Infrastructure and Application Solutions
- Appliance Servers
- Alpha Servers
- BackOffice Products
- Internet Products
- HPE 9000 and HPE e3000 Servers
- Networking
- Netservers
- Secure OS Software for Linux
- Server Management (Insight Manager 7)
- Windows Server 2003
- Operating System - Tru64 Unix
- ProLiant Deployment and Provisioning
- Linux-Based Community / Regional
- Microsoft System Center Integration
Discussion Boards
Discussion Boards
Discussion Boards
Discussion Boards
Discussion Boards
Discussion Boards
Discussion Boards
Discussion Boards
Discussion Boards
Discussion Boards
Discussion Boards
Discussion Boards
Discussion Boards
Discussion Boards
Discussion Boards
Discussion Boards
Discussion Boards
Discussion Boards
Discussion Boards
Discussion Boards
Discussion Boards
Discussion Boards
Community
Resources
Forums
Blogs
- Subscribe to RSS Feed
- Mark Topic as New
- Mark Topic as Read
- Float this Topic for Current User
- Bookmark
- Subscribe
- Printer Friendly Page
- Mark as New
- Bookmark
- Subscribe
- Mute
- Subscribe to RSS Feed
- Permalink
- Report Inappropriate Content
тАО07-15-2003 01:55 AM
тАО07-15-2003 01:55 AM
CPQKGPSA
- Mark as New
- Bookmark
- Subscribe
- Mute
- Subscribe to RSS Feed
- Permalink
- Report Inappropriate Content
тАО07-15-2003 06:22 AM
тАО07-15-2003 06:22 AM
Re: CPQKGPSA
Did you change anything recently? Upgraded? Reinstalled? Reconnected?
Eugeny
- Mark as New
- Bookmark
- Subscribe
- Mute
- Subscribe to RSS Feed
- Permalink
- Report Inappropriate Content
тАО07-15-2003 10:55 PM
тАО07-15-2003 10:55 PM
Re: CPQKGPSA
I have rebooted a couple of servers now with the same errors. These errors only appear in the log during the boot duration.
- Mark as New
- Bookmark
- Subscribe
- Mute
- Subscribe to RSS Feed
- Permalink
- Report Inappropriate Content
тАО07-15-2003 11:38 PM
тАО07-15-2003 11:38 PM
Re: CPQKGPSA
I am assuming it as a HP-UX server
Steps :
1.Try with ioscan command it will display the device is NOT_CLAIMED & NO_HW.
2.Install the pesudo drivers (insf -e)
3.Try again with ioscan command the Hardware is claimed or not.
Thanks & Regds,
Taranisen Mohanta
- Mark as New
- Bookmark
- Subscribe
- Mute
- Subscribe to RSS Feed
- Permalink
- Report Inappropriate Content
тАО07-16-2003 12:09 AM
тАО07-16-2003 12:09 AM
Re: CPQKGPSA
- Mark as New
- Bookmark
- Subscribe
- Mute
- Subscribe to RSS Feed
- Permalink
- Report Inappropriate Content
тАО07-16-2003 01:27 AM
тАО07-16-2003 01:27 AM
Re: CPQKGPSA
just some idea's as to where you could also look at :
- what is in between the servers and the
storage they boot from ? Did anything
changed at the FC switch level f/w or switch
config, zoning etc.
- any new devices added recently on the SAN ?
- any changes on the disk array settings or
config , LUNs added, removed etc etc ?
- if these are Brocade switches you have,what
do you see happening while the server tries
to boot (check via telnet session into the
switch and monitor), does that port do
multiple FLOGI etc etc.
Does the port gets properly logged in and is
it seen as a F-port right away when it
initializes at boot ?
- i have seen similar issues (but with local
SCSI disk to boot from and fibre card
connected to disk array for additional LUNs)
where it takes 15 min. for the FC driver to
time out and the server then continues to
boot W2K after that (Event log filled with
id=15 also). The FCcard/driver could not
see LUN0 on the disk array in that case.
This is not always a requirement anymore but
it used to be in the older days and depends
on the card's capability/settings and OS
version.
- if you enter the firmware config menu of the
Emulex card at bootup, can you properly see
the LUNs you need access to from that card?
i.e. LUN0 and the other LUNs where the copy
of the OS is on.
- no changes occurred to LUN security (LUN
masking, selective LUN presentation or
whatever name is used by the array vendor)
- do you have one or two fiber cards ?
If you have two, what happens if you
disconnect one fibre link and boot ?
HTH
Kris
- Mark as New
- Bookmark
- Subscribe
- Mute
- Subscribe to RSS Feed
- Permalink
- Report Inappropriate Content
тАО07-16-2003 02:18 AM
тАО07-16-2003 02:18 AM