MSA Storage
cancel
Showing results for 
Search instead for 
Did you mean: 

Cant access MSA1000 with scli

 
TanelKokk
Occasional Advisor

Cant access MSA1000 with scli

Hello

Regardless of that my system seems to recoginize my MSA1000 storage box, I'm not be able to access MSA1000 with scli utility.

my system description.

server: DL380 G4
HBA: QLogic QLA2340
HBA driver: 8.01.07-k4 (includes in kernel 2.6.20)
distro: Debian sarge 3.1 amd64
MSA1000

# lsmod
Module Size Used by
bonding 102672 0
qla2xxx 168844 0
firmware_class 12736 1 qla2xxx
scsi_transport_fc 44232 1 qla2xxx
ehci_hcd 37016 0
uhci_hcd 28832 0
tg3 115528 0

dmesg:
qla2xxx 0000:06:01.0: Found an ISP2312, irq 74, iobase 0xffffc2000001c000
qla2xxx 0000:06:01.0: Configuring PCI space...
qla2xxx 0000:06:01.0: Configure NVRAM parameters...
qla2xxx 0000:06:01.0: Verifying loaded RISC code...
qla2xxx 0000:06:01.0: Allocated (412 KB) for firmware dump...
scsi0 : qla2xxx
qla2xxx 0000:06:01.0: LIP reset occured (f7f7).
qla2xxx 0000:06:01.0: LOOP UP detected (2 Gbps).
qla2xxx 0000:06:01.0:
QLogic Fibre Channel HBA Driver: 8.01.07-k4
QLogic QLA2340 -
ISP2312: PCI-X (100 MHz) @ 0000:06:01.0 hdma+, host#=0, fw=3.03.18 IPX
ACPI: PCI Interrupt 0000:06:02.0 -> GSI 78 (level, low) -> IRQ 78
qla2xxx 0000:06:02.0: Found an ISP2312, irq 78, iobase 0xffffc2000001e000
qla2xxx 0000:06:02.0: Configuring PCI space...
qla2xxx 0000:06:02.0: Configure NVRAM parameters...
scsi 0:0:0:0: RAID COMPAQ MSA1000 4.48 PQ: 0 ANSI: 4
qla2xxx 0000:06:02.0: Verifying loaded RISC code...
qla2xxx 0000:06:02.0: Allocated (412 KB) for firmware dump...
ql...
























3 REPLIES 3
James Muell
Valued Contributor

Re: Cant access MSA1000 with scli

Have you tried using the Serial connection?
Have you tried connecting the serial port of the active controller to a switch port and then telneting to that port?
Are you trying CLI access from the host?
TanelKokk
Occasional Advisor

Re: Cant access MSA1000 with scli

> Have you tried using the Serial connection?
No

> Have you tried connecting the serial port of
> the active controller to a switch port and
> then telneting to that port?
Not yet.

> Are you trying CLI access from the host?
No, where can I get CLI utility?

(eh, hp.com download site is "Busy" at the moment :( )

btw, during boot there are messages on console (there are two HBA-s installed to server):

BIOS for adapter 0 is disabled

BIOS for adapter 1 is disabled
ROM BIOS NOT INSTALLED

Might this be problem?

Tanel

James Muell
Valued Contributor

Re: Cant access MSA1000 with scli

You can download the Arry Configuration Utility for Linux and install it. I believe you will also need to install the HP management package before loading the ACU.
THis gives you gui access to the ACU.



Here is a link to the cli tool
http://h18023.www1.hp.com/support/files/server/us/download/26011.html

Here is the sup pack link:
http://h18023.www1.hp.com/support/files/server/us/download/22265.html

I think this is the ACU gui tool link:
http://h18023.www1.hp.com/support/files/server/us/download/25410.html