- Community Home
- >
- Storage
- >
- Entry Storage Systems
- >
- MSA Storage
- >
- Re: Command View Remote Access
Categories
Company
Local Language
Forums
Discussions
Forums
- Data Protection and Retention
- Entry Storage Systems
- Legacy
- Midrange and Enterprise Storage
- Storage Networking
- HPE Nimble Storage
Discussions
Discussions
Discussions
Forums
Forums
Discussions
Discussion Boards
Discussion Boards
Discussion Boards
Discussion Boards
- BladeSystem Infrastructure and Application Solutions
- Appliance Servers
- Alpha Servers
- BackOffice Products
- Internet Products
- HPE 9000 and HPE e3000 Servers
- Networking
- Netservers
- Secure OS Software for Linux
- Server Management (Insight Manager 7)
- Windows Server 2003
- Operating System - Tru64 Unix
- ProLiant Deployment and Provisioning
- Linux-Based Community / Regional
- Microsoft System Center Integration
Discussion Boards
Discussion Boards
Discussion Boards
Discussion Boards
Discussion Boards
Discussion Boards
Discussion Boards
Discussion Boards
Discussion Boards
Discussion Boards
Discussion Boards
Discussion Boards
Discussion Boards
Discussion Boards
Discussion Boards
Discussion Boards
Discussion Boards
Discussion Boards
Discussion Boards
Discussion Boards
Discussion Boards
Discussion Boards
Community
Resources
Forums
Blogs
- Subscribe to RSS Feed
- Mark Topic as New
- Mark Topic as Read
- Float this Topic for Current User
- Bookmark
- Subscribe
- Printer Friendly Page
- Mark as New
- Bookmark
- Subscribe
- Mute
- Subscribe to RSS Feed
- Permalink
- Report Inappropriate Content
тАО12-05-2002 12:21 PM
тАО12-05-2002 12:21 PM
Command View Remote Access
What am I missing ??
- Mark as New
- Bookmark
- Subscribe
- Mute
- Subscribe to RSS Feed
- Permalink
- Report Inappropriate Content
тАО12-05-2002 11:41 PM
тАО12-05-2002 11:41 PM
Re: Command View Remote Access
adding your W2K pc's IP address to the access.dat file and stop/starting the hostagent on the server that has CommandView running should be enough in a standard config.
The best way to verify if the web server on the host that runs CommandView is working is connect to http://server_ip_address:4096 , this should give you this message in the browser :
"(c) Copyright 2000-2002 - Hewlett-Packard Company hp StorageWorks CommandView SDM web server"
If this does not work then the Cmdv webserver does not run and you should change the c:\sanmgr\commandview\server\config\PanConfigParams.txt file and edit it so that the parameter called WEBSERVER_ENABLED is set to true. I think this is ok in your config given the error message you get back.
The above example is for a config where the webserver runs on a Windows server, not sure on what OS your CommandView runs (UX or Windows) but the file to edit (PanConfigParams) is the same.
Other then this from the network point of view it seems to be ok because you get a reply back from the web server.
If the above does not help, try to put *.*.*.* in the access.dat just for a test to allow all IP addresses to connect to the Cmdv webserver.
HTH
Kris
- Mark as New
- Bookmark
- Subscribe
- Mute
- Subscribe to RSS Feed
- Permalink
- Report Inappropriate Content
тАО12-06-2002 12:31 AM
тАО12-06-2002 12:31 AM
Re: Command View Remote Access
here's something in addition what Kris has mentioned
http://forums.itrc.hp.com/cm/QuestionAnswer/1,,0x977b85079106d71190050090279cd0f9,00.html
Eugeny
- Mark as New
- Bookmark
- Subscribe
- Mute
- Subscribe to RSS Feed
- Permalink
- Report Inappropriate Content
тАО12-06-2002 12:56 AM
тАО12-06-2002 12:56 AM
Re: Command View Remote Access
since you did not specified the OS that runs on the host connected to the VA7400 the test below might not be valid since it is intended for Windows hosts only.
Try to run the remote acces locally on the Windows server itself by pointing your browser to http://server_ip_address:4096 or http://server_ip_address:4096/Launcher.html"
to verify if acces locally is working fine or not.
You can also use the servers hostname, 127.0.0.1 or localhost, all of this should work locally.
regards, Kris
- Mark as New
- Bookmark
- Subscribe
- Mute
- Subscribe to RSS Feed
- Permalink
- Report Inappropriate Content
тАО12-09-2002 07:00 AM
тАО12-09-2002 07:00 AM
Re: Command View Remote Access
Thanks again to all!