- Community Home
- >
- Storage
- >
- Entry Storage Systems
- >
- MSA Storage
- >
- Re: Hoe to configure MSA1000 for OpenVMS ?
Categories
Company
Local Language
Forums
Discussions
Forums
- Data Protection and Retention
- Entry Storage Systems
- Legacy
- Midrange and Enterprise Storage
- Storage Networking
- HPE Nimble Storage
Discussions
Discussions
Discussions
Forums
Forums
Discussions
Discussion Boards
Discussion Boards
Discussion Boards
Discussion Boards
- BladeSystem Infrastructure and Application Solutions
- Appliance Servers
- Alpha Servers
- BackOffice Products
- Internet Products
- HPE 9000 and HPE e3000 Servers
- Networking
- Netservers
- Secure OS Software for Linux
- Server Management (Insight Manager 7)
- Windows Server 2003
- Operating System - Tru64 Unix
- ProLiant Deployment and Provisioning
- Linux-Based Community / Regional
- Microsoft System Center Integration
Discussion Boards
Discussion Boards
Discussion Boards
Discussion Boards
Discussion Boards
Discussion Boards
Discussion Boards
Discussion Boards
Discussion Boards
Discussion Boards
Discussion Boards
Discussion Boards
Discussion Boards
Discussion Boards
Discussion Boards
Discussion Boards
Discussion Boards
Discussion Boards
Discussion Boards
Discussion Boards
Discussion Boards
Discussion Boards
Community
Resources
Forums
Blogs
- Subscribe to RSS Feed
- Mark Topic as New
- Mark Topic as Read
- Float this Topic for Current User
- Bookmark
- Subscribe
- Printer Friendly Page
- Mark as New
- Bookmark
- Subscribe
- Mute
- Subscribe to RSS Feed
- Permalink
- Report Inappropriate Content
тАО12-16-2004 02:27 AM
тАО12-16-2004 02:27 AM
I must to add 2 disk drives and create a new LUN to an MSA1000 with OpenVMS firmware.
I haven't knowledge of OpenVMS and MSA1000 cli.
Anyone can help me with MSA1000 commands ?
thanks in advance
best regards
Davide
Solved! Go to Solution.
- Mark as New
- Bookmark
- Subscribe
- Mute
- Subscribe to RSS Feed
- Permalink
- Report Inappropriate Content
тАО12-20-2004 07:31 PM
тАО12-20-2004 07:31 PM
SolutionFirst;
make sure that you have some connectivity to the MSA1000 controller via the "special" serial console cable.
when you are connected to the command line of the MSA1000 you have to use the following commands
SET HOST /DTE TT /SPEED=19200
BTW. all commands are based on adding a new set of disks.
The mentioned numbers are example numbers. The unit number is what you define; the DISK numbers are the physical disk numbers.
First you need to add a unit number for the physical diskset. (in here for a RAID 0+1 set)
> ADD UNIT 26 raid_level=1 data="DISK113 DISK213"
assign the unit ID to this diskset
> SET UNIT_ID 26 501\r
note: this will be the DGA number externally visible on VMS system
optionally enable the cache;
> SET UNIT 26 cache=enabled
optionally assign spare disks to this unit
> ADD SPARE unit=26 "DISK108"
good luck ...
- Mark as New
- Bookmark
- Subscribe
- Mute
- Subscribe to RSS Feed
- Permalink
- Report Inappropriate Content
тАО12-20-2004 09:05 PM
тАО12-20-2004 09:05 PM
Re: Hoe to configure MSA1000 for OpenVMS ?
kind regards
Davide
- Mark as New
- Bookmark
- Subscribe
- Mute
- Subscribe to RSS Feed
- Permalink
- Report Inappropriate Content
тАО12-22-2004 12:28 PM
тАО12-22-2004 12:28 PM
Re: Hoe to configure MSA1000 for OpenVMS ?
- Mark as New
- Bookmark
- Subscribe
- Mute
- Subscribe to RSS Feed
- Permalink
- Report Inappropriate Content
тАО12-22-2004 07:01 PM
тАО12-22-2004 07:01 PM
Re: Hoe to configure MSA1000 for OpenVMS ?
I haven't seen any needs for that. Is there a specific reason to do? In our case the connections were initiated, and indicated the right OS....
Rgrds,
Cees Zee
- Mark as New
- Bookmark
- Subscribe
- Mute
- Subscribe to RSS Feed
- Permalink
- Report Inappropriate Content
тАО12-22-2004 07:13 PM
тАО12-22-2004 07:13 PM
Re: Hoe to configure MSA1000 for OpenVMS ?
Two or three years ago I've been told about a user whose AlphaServer GS160 (running SAP R/3) crashed due to an invalid connection setting on the HSG80.
Trust me - you really, really want to make the correct setup!
- Mark as New
- Bookmark
- Subscribe
- Mute
- Subscribe to RSS Feed
- Permalink
- Report Inappropriate Content
тАО12-22-2004 07:37 PM
тАО12-22-2004 07:37 PM
Re: Hoe to configure MSA1000 for OpenVMS ?
What I actually meant to say is that the MSA1000 (already) picked up the profile in the connection.
However, thanks for the information. I will need to keep an eye on it ... (At this moment the MSA1000 is only used by OpenVMS (for 2 and 3 node clusters), it will become a hot topic when the array will be shared with more OSes).
- Mark as New
- Bookmark
- Subscribe
- Mute
- Subscribe to RSS Feed
- Permalink
- Report Inappropriate Content
тАО12-23-2004 05:13 AM
тАО12-23-2004 05:13 AM
Re: Hoe to configure MSA1000 for OpenVMS ?
- Mark as New
- Bookmark
- Subscribe
- Mute
- Subscribe to RSS Feed
- Permalink
- Report Inappropriate Content
тАО08-08-2007 12:12 AM
тАО08-08-2007 12:12 AM