MSA Storage
cancel
Showing results for 
Search instead for 
Did you mean: 

MSA1500 flashing like christmas tree but with no obvious error in logs

 
Stephen Delaney
Occasional Visitor

MSA1500 flashing like christmas tree but with no obvious error in logs

Hi,

I have recently relocated our MSA1500 (+msa30+msa20) to our DR datacenter. Originally it was configured under windows based ACU but due to no windows based connections at our DR site I have had to configure via the CLI. Once installed, it seemed ok and the front lights acted normally but since then the MSA30 is alternating flashing between the first 6 disks and the last 8 and the MSA20 drives are just showing a constant blue light. I have ran a 'show tech_support' but nothing on there is telling me I have problems. Would someone mind having a look and let me know if I have missed something please?

### BEGIN LOG - DATE: 090715, TIME: 113258 ###

show tech_support

CLI-1> show version -all
MSA1500 Firmware Revision: 7.00b1500 (SGA053501T)
Build Time: 2007-01-24 16:13:17
MSA1500 Hardware Revision: a [AutoRev: 0x030000]
Fibre Module AutoRev: 0x020000
SCSI I/O Module Bus 0 Revision: 2.02
SCSI I/O Module Bus 1 Revision: <>
SCSI I/O Module Bus 2 Revision: 2.02
SCSI I/O Module Bus 3 Revision: <>
Fan Control Module A Revision: 2.38
Fan Control Module B Revision: 2.38
Box 3 PROLIANT 4LEE Rev: CP20 (MBNDLMPX9C)
Box 5 PROLIANT 8LCE Rev: 2.02 (E00SMLJ193)
Box 5 Fan Control Module A Rev: 2.38
Box 5 Fan Control Module B Rev: 2.38

Disk Drives:
B T L BOX BAY GB Model Rev. Serial No.
0 4 1 5 1 500.0 Unknown GB0500C4413 HPG 9QG3BZPC
0 4 2 5 2 500.0 Unknown GB0500C4413 HPG 9QG2HSS7
0 4 3 5 3 500.0 Unknown GB0500C4413 HPG 9QG2E0H8
0 4 4 5 4 500.0 Unknown GB0500C4413 HPG 9QG2GPVS
0 4 5 5 5 500.0 Unknown GB0500C4413 HPG 9QG3BVW0
0 4 6 5 6 500.0 Unknown GB0500C4413 HPG 9QG2291C
0 4 7 5 7 500.0 Unknown GB0500C4413 HPG 9QG3BWSX
0 4 8 5 8 500.0 Unknown GB0500C4413 HPG 9QG3C5CF
0 4 9 5 9 500.0 Unknown GB0500C4413 HPG 9QG3BWYQ
0 4 10 5 10 500.0 Unknown GB0500C4413 HPG 9QG3BX2W
0 4 11 5 11 500.0 Unknown GB0500C4413 HPG 9QG0HMJ8
0 4 12 5 12 500.0 Unknown GB0500C4413 HPG 9QG2C311
2 0 0 3 1 300.0 COMPAQ BD30089BBA HPB1 DA01P780DMM00732
2 1 0 3 2 300.0 COMPAQ BD30089BBA HPB1 DA01P780DNPC0732
2 2 0 3 3 300.0 COMPAQ BD30089BBA HPB1 DA01P780DRN60733
2 3 0 3 4 300.0 COMPAQ BD30089BBA HPB1 DA01P780DNKJ0732
2 4 0 3 5 300.0 COMPAQ BD30089BBA HPB1 DA01P810GSHR0805
2 5 0 3 6 300.0 COMPAQ BD30089BBA HPB1 DA01P780DMWB0732
2 8 0 3 7 300.0 COMPAQ BD30089BBA HPB1 DA01P780DMW50732
2 9 0 3 8 300.0 COMPAQ BD30089BBA HPB1 DA01P780DNRL0732
2 10 0 3 9 300.0 COMPAQ BD30089BBA HPB1 DA01P780DNUU0732
2 11 0 3 10 300.0 COMPAQ BD30089BBA HPB1 DA01P780DNY10732
2 12 0 3 11 300.0 COMPAQ BD30089BBA HPB1 DA01P780DNP70732
2 13 0 3 12 300.0 COMPAQ BD30089BBA HPB1 DA01P780DMPF0732
2 14 0 3 13 300.0 COMPAQ BD30089BBA HPB1 DA01P780DNR30732
2 15 0 3 14 300.0 COMPAQ BD30089BBA HPB1 DA01P780DNY50732


CLI-1> show profile
Profile name = Default (Default) Mode value = (00002405)

Mode 0 = Peripheral Device LUN Addressing
Mode 1 = Legacy Failover
Mode 2 = Logical volumes connect as available on Backup Controller
Mode 3 = Product ID of 'MSA1000 VOLUME' (only if Active-Standby mode)
Mode 4 = Normal bad block handling
Mode 5 = Logout selected initiators on TPRLO
Mode 6 = Fault management events not reported through Unit Attention
Mode 7 = Do not send FCP response info with SCSI status
Mode 8 = Do not send Unit Attention on failover
Mode 9 = SCSI inquiry revision field contains the actual version
Mode 10 = SCSI inquiry vendor ID='HP'
Mode 11 = Power On Reset Unit Attention generated on FC Login or Logout
Mode 12 = Ignore Force Unit Access on Write
Mode 13 = Admit Target Port on Reservation
Mode 14 = Asymmetrical Active/Active Operating Mode

Profile name = Windows
Type = Standard Mode value = (00002405)

Mode 0 = Peripheral Device LUN Addressing
Mode 1 = Legacy Failover
Mode 2 = Logical volumes connect as available on Backup Controller
Mode 3 = Product ID of 'MSA1000 VOLUME' (only if Active-Standby mode)
Mode 4 = Normal bad block handling
Mode 5 = Logout selected initiators on TPRLO
Mode 6 = Fault management events not reported through Unit Attention
Mode 7 = Do not send FCP response info with SCSI status
Mode 8 = Do not send Unit Attention on failover
Mode 9 = SCSI inquiry revision field contains the actual version
Mode 10 = SCSI inquiry vendor ID='HP'
Mode 11 = Power On Reset Unit Attention generated on FC Login or Logout
Mode 12 = Ignore Force Unit Access on Write
Mode 13 = Admit Target Port on Reservation
Mode 14 = Asymmetrical Active/Active Operating Mode

Profile name = Windows (degraded performance)
Type = Standard Mode value = (00003405)

Mode 0 = Peripheral Device LUN Addressing
Mode 1 = Legacy Failover
Mode 2 = Logical volumes connect as available on Backup Controller
Mode 3 = Product ID of 'MSA1000 VOLUME' (only if Active-Standby mode)
Mode 4 = Normal bad block handling
Mode 5 = Logout selected initiators on TPRLO
Mode 6 = Fault management events not reported through Unit Attention
Mode 7 = Do not send FCP response info with SCSI status
Mode 8 = Do not send Unit Attention on failover
Mode 9 = SCSI inquiry revision field contains the actual version
Mode 10 = SCSI inquiry vendor ID='HP'
Mode 11 = Power On Reset Unit Attention generated on FC Login or Logout
Mode 12 = Enforce Force Unit Access on Write
Mode 13 = Admit Target Port on Reservation
Mode 14 = Asymmetrical Active/Active Operating Mode

Profile name = OpenVMS
Type = Standard Mode value = (00003473)

Mode 0 = Peripheral Device LUN Addressing
Mode 1 = Asymmetric Failover
Mode 2 = Logical volumes connect as unavailable on Backup Controller
Mode 3 = Product ID of 'MSA1000 VOLUME' (only if Active-Standby mode)
Mode 4 = VMS shadow style bad block handling
Mode 5 = Logout all initiators on TPRLO
Mode 6 = Fault management events reported through Unit Attention
Mode 7 = Do not send FCP response info with SCSI status
Mode 8 = Do not send Unit Attention on failover
Mode 9 = SCSI inquiry revision field contains the actual version
Mode 10 = SCSI inquiry vendor ID='HP'
Mode 11 = Power On Reset Unit Attention generated on FC Login or Logout
Mode 12 = Enforce Force Unit Access on Write
Mode 13 = Admit Target Port on Reservation
Mode 14 = Asymmetrical Active/Active Operating Mode

Profile name = Tru64
Type = Standard Mode value = (00003563)

Mode 0 = Peripheral Device LUN Addressing
Mode 1 = Asymmetric Failover
Mode 2 = Logical volumes connect as unavailable on Backup Controller
Mode 3 = Product ID of 'MSA1000 VOLUME' (only if Active-Standby mode)
Mode 4 = Normal bad block handling
Mode 5 = Logout all initiators on TPRLO
Mode 6 = Fault management events reported through Unit Attention
Mode 7 = Do not send FCP response info with SCSI status
Mode 8 = Send Unit Attention on failover
Mode 9 = SCSI inquiry revision field contains the actual version
Mode 10 = SCSI inquiry vendor ID='HP'
Mode 11 = Power On Reset Unit Attention generated on FC Login or Logout
Mode 12 = Enforce Force Unit Access on Write
Mode 13 = Admit Target Port on Reservation
Mode 14 = Asymmetrical Active/Active Operating Mode

Profile name = Linux
Type = Standard Mode value = (000034a7)

Mode 0 = Peripheral Device LUN Addressing
Mode 1 = Asymmetric Failover
Mode 2 = Logical volumes connect as available on Backup Controller
Mode 3 = Product ID of 'MSA1000 VOLUME' (only if Active-Standby mode)
Mode 4 = Normal bad block handling
Mode 5 = Logout all initiators on TPRLO
Mode 6 = Fault management events not reported through Unit Attention
Mode 7 = Send FCP response info with SCSI status
Mode 8 = Do not send Unit Attention on failover
Mode 9 = SCSI inquiry revision field contains the actual version
Mode 10 = SCSI inquiry vendor ID='HP'
Mode 11 = Power On Reset Unit Attention generated on FC Login or Logout
Mode 12 = Enforce Force Unit Access on Write
Mode 13 = Admit Target Port on Reservation
Mode 14 = Asymmetrical Active/Active Operating Mode

Profile name = Solaris
Type = Standard Mode value = (000034a7)

Mode 0 = Peripheral Device LUN Addressing
Mode 1 = Asymmetric Failover
Mode 2 = Logical volumes connect as available on Backup Controller
Mode 3 = Product ID of 'MSA1000 VOLUME' (only if Active-Standby mode)
Mode 4 = Normal bad block handling
Mode 5 = Logout all initiators on TPRLO
Mode 6 = Fault management events not reported through Unit Attention
Mode 7 = Send FCP response info with SCSI status
Mode 8 = Do not send Unit Attention on failover
Mode 9 = SCSI inquiry revision field contains the actual version
Mode 10 = SCSI inquiry vendor ID='HP'
Mode 11 = Power On Reset Unit Attention generated on FC Login or Logout
Mode 12 = Enforce Force Unit Access on Write
Mode 13 = Admit Target Port on Reservation
Mode 14 = Asymmetrical Active/Active Operating Mode

Profile name = Netware
Type = Standard Mode value = (000034a7)

Mode 0 = Peripheral Device LUN Addressing
Mode 1 = Asymmetric Failover
Mode 2 = Logical volumes connect as available on Backup Controller
Mode 3 = Product ID of 'MSA1000 VOLUME' (only if Active-Standby mode)
Mode 4 = Normal bad block handling
Mode 5 = Logout all initiators on TPRLO
Mode 6 = Fault management events not reported through Unit Attention
Mode 7 = Send FCP response info with SCSI status
Mode 8 = Do not send Unit Attention on failover
Mode 9 = SCSI inquiry revision field contains the actual version
Mode 10 = SCSI inquiry vendor ID='HP'
Mode 11 = Power On Reset Unit Attention generated on FC Login or Logout
Mode 12 = Enforce Force Unit Access on Write
Mode 13 = Admit Target Port on Reservation
Mode 14 = Asymmetrical Active/Active Operating Mode

Profile name = HP
Type = Standard Mode value = (00003ca6)

Mode 0 = Volume Set Addressing
Mode 1 = Asymmetric Failover
Mode 2 = Logical volumes connect as available on Backup Controller
Mode 3 = Product ID of 'MSA1000 VOLUME' (only if Active-Standby mode)
Mode 4 = Normal bad block handling
Mode 5 = Logout all initiators on TPRLO
Mode 6 = Fault management events not reported through Unit Attention
Mode 7 = Send FCP response info with SCSI status
Mode 8 = Do not send Unit Attention on failover
Mode 9 = SCSI inquiry revision field contains the actual version
Mode 10 = SCSI inquiry vendor ID='HP'
Mode 11 = No Power On Reset Unit Attention generated on FC Login or Logout
Mode 12 = Enforce Force Unit Access on Write
Mode 13 = Admit Target Port on Reservation
Mode 14 = Asymmetrical Active/Active Operating Mode

Profile name = XP Storage Array
Type = Standard Mode value = (00003563)

Mode 0 = Peripheral Device LUN Addressing
Mode 1 = Asymmetric Failover
Mode 2 = Logical volumes connect as unavailable on Backup Controller
Mode 3 = Product ID of 'MSA1000 VOLUME' (only if Active-Standby mode)
Mode 4 = Normal bad block handling
Mode 5 = Logout all initiators on TPRLO
Mode 6 = Fault management events reported through Unit Attention
Mode 7 = Do not send FCP response info with SCSI status
Mode 8 = Send Unit Attention on failover
Mode 9 = SCSI inquiry revision field contains the actual version
Mode 10 = SCSI inquiry vendor ID='HP'
Mode 11 = Power On Reset Unit Attention generated on FC Login or Logout
Mode 12 = Enforce Force Unit Access on Write
Mode 13 = Admit Target Port on Reservation
Mode 14 = Asymmetrical Active/Active Operating Mode


CLI-1> show globals

Global Parameters:
System Name: DAR-MSA1500
Rebuild Priority: low
Expand Priority: medium
Surface Delay: 3.0 seconds

Total Cache: 512MB
50% Read Cache: 256MB
50% Write Cache: 256MB

Temperature:
EMU: 25 Celsius, 77 Fahrenheit
PS1: 24 Celsius, 75 Fahrenheit
PS2: 25 Celsius, 77 Fahrenheit

CLI-1> show acl

ACL is enabled:
Connection WWPN Units
DARVM01 50014380-029C2296 0, 1, 2, 3, 4, 5, 6
DARVM02 50014380-03AEC41A 0, 1, 2, 3, 4, 5, 6
Inaccessible Units: None

CLI-1> show connections

Connection Name: DARVM02
Host WWNN = 50014380-03AEC41B
Host WWPN = 50014380-03AEC41A
Profile Name = Linux
Unit Offset = 0
Controller 1 Port 1 Status = Online
Controller 2 Port 1 Status = Online

Connection Name: DARVM01
Host WWNN = 50014380-029C2297
Host WWPN = 50014380-029C2296
Profile Name = Linux
Unit Offset = 0
Controller 1 Port 1 Status = Online
show disks Controller 2 Port 1 Status = Online

Disk List: (box,bay) (B:T:L) Size Speed Units

CLI-1> Enclosure 3: SCSI (2:06:00) PROLIANT 4LEE CP20
show box Disk301 (3,01) (2:00:00) 300.0GB 160 MB/s
3
Disk302 (3,02) (2:01:00) 300.0GB 160 MB/s 3
Disk303 (3,03) (2:02:00) 300.0GB 160 MB/s 3
Disk304 (3,04) (2:03:00) 300.0GB 160 MB/s 3
Disk305 (3,05) (2:04:00) 300.0GB 160 MB/s 4
Disk306 (3,06) (2:05:00) 300.0GB 160 MB/s 4
Disk307 (3,07) (2:08:00) 300.0GB 160 MB/s 4
Disk308 (3,08) (2:09:00) 300.0GB 160 MB/s 4
Disk309 (3,09) (2:10:00) 300.0GB 160 MB/s 5
Disk310 (3,10) (2:11:00) 300.0GB 160 MB/s 5
Disk311 (3,11) (2:12:00) 300.0GB 160 MB/s 5
Disk312 (3,12) (2:13:00) 300.0GB 160 MB/s 5
Disk313 (3,13) (2:14:00) 300.0GB 160 MB/s 6
Disk314 (3,14) (2:15:00) 300.0GB 160 MB/s 3, 4, 5 (spare)
Enclosure 5: SATA (0:04:00) PROLIANT 8LCE 2.02
Disk501 (5,01) (0:04:01) 500.0GB 160 MB/s 0
Disk502 (5,02) (0:04:02) 500.0GB 160 MB/s 0
Disk503 (5,03) (0:04:03) 500.0GB 160 MB/s 0
Disk504 (5,04) (0:04:04) 500.0GB 160 MB/s 0
Disk505 (5,05) (0:04:05) 500.0GB 160 MB/s 1
Disk506 (5,06) (0:04:06) 500.0GB 160 MB/s 1
Disk507 (5,07) (0:04:07) 500.0GB 160 MB/s 1
Disk508 (5,08) (0:04:08) 500.0GB 160 MB/s 1
Disk509 (5,09) (0:04:09) 500.0GB 160 MB/s 2
Disk510 (5,10) (0:04:10) 500.0GB 160 MB/s 2
Disk511 (5,11) (0:04:11) 500.0GB 160 MB/s 2
Disk512 (5,12) (0:04:12) 500.0GB 160 MB/s 0, 1, 2 (spare)

Notes:
The speed is the currently negotiated speed to the disk. This may
be less than the maximum speed supported by the device due to bus
faults, loss of signal integrity, etc.


CLI-1> Box #3:
SCSI enclosure at bus 2 channel 0 target 6
show units Firmware ID string: PROLIANT 4LEE

Firmware revision: CP20
Serial number: MBNDLMPX9C
Environmental Status:
No alert conditions reported

Box #5:
SATA enclosure at bus 0 channel 1 target 4
Firmware ID string: PROLIANT 8LCE
Firmware revision: 2.02
Serial number: E00SMLJ193
Environmental Status:
No alert conditions reported
Cache Information:
Total Memory: 112MB
Read Cache: 56MB
Write Cache: 56MB
Cache Status: Enabled
Battery #1 (lower): OK
Battery #2 (upper): OK

Unit 0:

CLI-1> In PDLA mode, Unit 0 is Lun 1; In VSA mode, Unit 0 is Lun 0.
show this_controllerUnit Identifier : DAR-VMSTORAGE1

Device Identifier : 600508B3-0091A190-0D1BEC97-B7540002
Preferred Path : Controller 1 (this controller)
Cache Status : Enabled
Max Boot Partition: Disabled
Volume Status : VOLUME OK
Parity Init Status: Complete
4 Data Disk(s) used by lun 0:
Disk501: Box 5, Bay 01, (B:T:L 0:04:01)
Disk502: Box 5, Bay 02, (B:T:L 0:04:02)
Disk503: Box 5, Bay 03, (B:T:L 0:04:03)
Disk504: Box 5, Bay 04, (B:T:L 0:04:04)
Spare Disk(s) used by lun 0:
Disk512: Box 5, Bay 12, (B:T:L 0:04:12)
Logical Volume Raid Level: DISTRIBUTED PARITY FAULT TOLERANCE (RAID 5)
stripe_size=64kB
Logical Volume Capacity : 1,430,721MB

Unit 1:
In PDLA mode, Unit 1 is Lun 2; In VSA mode, Unit 1 is Lun 1.
Unit Identifier : DAR-VMSTORAGE2
Device Identifier : 600508B3-0091A190-F8B985C9-D1090003
Preferred Path : Controller 1 (this controller)
Cache Status : Enabled
Max Boot Partition: Disabled
Volume Status : VOLUME OK
Parity Init Status: Complete
4 Data Disk(s) used by lun 1:
Disk505: Box 5, Bay 05, (B:T:L 0:04:05)
Disk506: Box 5, Bay 06, (B:T:L 0:04:06)
Disk507: Box 5, Bay 07, (B:T:L 0:04:07)
Disk508: Box 5, Bay 08, (B:T:L 0:04:08)
Spare Disk(s) used by lun 1:
Disk512: Box 5, Bay 12, (B:T:L 0:04:12)
Logical Volume Raid Level: DISTRIBUTED PARITY FAULT TOLERANCE (RAID 5)
stripe_size=64kB
Logical Volume Capacity : 1,430,721MB

Unit 2:
In PDLA mode, Unit 2 is Lun 3; In VSA mode, Unit 2 is Lun 2.
Unit Identifier : DAR-VMSTORAGE3
Device Identifier : 600508B3-0091A190-61F1F724-E8F20004
Preferred Path : Controller 2 (other controller)
Cache Status : Enabled
Max Boot Partition: Disabled
Volume Status : VOLUME OK
Parity Init Status: Complete
3 Data Disk(s) used by lun 2:
Disk509: Box 5, Bay 09, (B:T:L 0:04:09)
Disk510: Box 5, Bay 10, (B:T:L 0:04:10)
Disk511: Box 5, Bay 11, (B:T:L 0:04:11)
Spare Disk(s) used by lun 2:
Disk512: Box 5, Bay 12, (B:T:L 0:04:12)
Logical Volume Raid Level: DISTRIBUTED PARITY FAULT TOLERANCE (RAID 5)
stripe_size=64kB
Logical Volume Capacity : 953,811MB

Unit 3:
In PDLA mode, Unit 3 is Lun 4; In VSA mode, Unit 3 is Lun 3.
Unit Identifier :
Device Identifier : 600508B3-0091A190-7C3ABE8E-51C70006
Preferred Path : Controller 1 (this controller)
Cache Status : Enabled
Max Boot Partition: Enabled
Volume Status : VOLUME OK
Parity Init Status: Complete
4 Data Disk(s) used by lun 3:
Disk301: Box 3, Bay 01, (B:T:L 2:00:00)
Disk302: Box 3, Bay 02, (B:T:L 2:01:00)
Disk303: Box 3, Bay 03, (B:T:L 2:02:00)
Disk304: Box 3, Bay 04, (B:T:L 2:03:00)
Spare Disk(s) used by lun 3:
Disk314: Box 3, Bay 14, (B:T:L 2:15:00)
Logical Volume Raid Level: DISTRIBUTED PARITY FAULT TOLERANCE (RAID 5)
stripe_size=64kB
Logical Volume Capacity : 858,300MB

Unit 4:
In PDLA mode, Unit 4 is Lun 5; In VSA mode, Unit 4 is Lun 4.
Unit Identifier :
Device Identifier : 600508B3-0091A190-A51E53C5-8CD80007
Preferred Path : Controller 2 (other controller)
Cache Status : Enabled
Max Boot Partition: Enabled
Volume Status : VOLUME OK
Parity Init Status: Complete
4 Data Disk(s) used by lun 4:
Disk305: Box 3, Bay 05, (B:T:L 2:04:00)
Disk306: Box 3, Bay 06, (B:T:L 2:05:00)
Disk307: Box 3, Bay 07, (B:T:L 2:08:00)
Disk308: Box 3, Bay 08, (B:T:L 2:09:00)
Spare Disk(s) used by lun 4:
Disk314: Box 3, Bay 14, (B:T:L 2:15:00)
Logical Volume Raid Level: DISTRIBUTED PARITY FAULT TOLERANCE (RAID 5)
stripe_size=64kB
Logical Volume Capacity : 858,300MB

Unit 5:
In PDLA mode, Unit 5 is Lun 6; In VSA mode, Unit 5 is Lun 5.
Unit Identifier :
Device Identifier : 600508B3-0091A190-4D6A6F64-525B0008
Preferred Path : Controller 2 (other controller)
Cache Status : Enabled
Max Boot Partition: Enabled
Volume Status : VOLUME OK
Parity Init Status: Complete
4 Data Disk(s) used by lun 5:
Disk309: Box 3, Bay 09, (B:T:L 2:10:00)
Disk310: Box 3, Bay 10, (B:T:L 2:11:00)
Disk311: Box 3, Bay 11, (B:T:L 2:12:00)
Disk312: Box 3, Bay 12, (B:T:L 2:13:00)
Spare Disk(s) used by lun 5:
Disk314: Box 3, Bay 14, (B:T:L 2:15:00)
Logical Volume Raid Level: DISTRIBUTED PARITY FAULT TOLERANCE (RAID 5)
stripe_size=64kB
Logical Volume Capacity : 858,300MB

Unit 6:
In PDLA mode, Unit 6 is Lun 7; In VSA mode, Unit 6 is Lun 6.
Unit Identifier :
Device Identifier : 600508B3-0091A190-28A209DE-E4700009
Preferred Path : Controller 2 (other controller)
Cache Status : Enabled
Max Boot Partition: Enabled
Volume Status : VOLUME OK
1 Data Disk(s) used by lun 6:
Disk313: Box 3, Bay 13, (B:T:L 2:14:00)
Spare Disk(s) used by lun 6:
No spare drive is designated.
Logical Volume Raid Level: NO FAULT TOLERANCE (RAID 0)
stripe_size=128kB
Logical Volume Capacity : 286,095MB

CLI-1> Controller 1 (right controller):
MSA1500(c) Hewlett-Packard PB9840TX3V109A Version 7.00 Build 1500 Hardware A
Build Time: 2007-01-24 16:13:17
Component Enclosure.
Controller Identifier:
NODE_ID = 500508B3-0091A190
SCSI_VERSION = SCSI-3
Supported Redundancy Mode: Active/Standby Asym-Active/Active
Current Redundancy Mode: Asym-Active/Active
Device Port SCSI address 6
Terminal speed for the CLI is set to 19200.
Host Port_1:
REPORTED PORT_ID 500508B3-0091A191
PORT_1_TOPOLOGY = F_Port
Cache:
256 megabyte read cache 256 megabyte write cache Version 2
Cache is GOOD, and Cache is enabled.
Unflushed data in cache
Batteries are enabled
Module #1 is fully charged and turned on.
Module #2 is fully charged and turned on.
Controller Up Time:
6 Days 16 Hours 26 Minutes 48 Seconds
Health:
Surface Scan: Complete.
Rebuild Status: Complete.
Expansion: Complete.
show other_controller

CLI-1> Controller 2 (left controller):
MSA1500(c) Hewlett-Packard P56350HX3SP04W Version 7.00 Build 1500 Hardware 7
Build Time: 2007-01-24 16:13:17
Component Enclosure.
Controller Identifier:
NODE_ID = 500508B3-0091A190
SCSI_VERSION = SCSI-3
Supported Redundancy Mode: Active/Standby Asym-Active/Active
Current Redundancy Mode: Asym-Active/Active
Device Port SCSI address 7
Terminal speed for the CLI is set to 19200.
Host Port_1:
REPORTED PORT_ID 500508B3-0091A199
PORT_1_TOPOLOGY = F_Port
Cache:
256 megabyte read cache 256 megabyte write cache Version 2
Cache is GOOD, and Cache is enabled.
No unflushed data in cache
Batteries are disabled
Module #1 is fully charged and turned off.
Module #2 is fully charged and turned off.
Controller Up Time:
6 Days 16 Hours 30 Minutes 53 Seconds
Health:
Surface Scan: Complete.
Rebuild Status: Complete.
Expansion: Complete.
show eventlog
TIME CLASS SUB DETL MESSAGE

CLI-1> 0d 01:29:31.2 0006 0000 0000 Redundant operation state change.
show preferred_path0d 01:36:13.2 0006 0000 0000 Redundant operation state change.

0d 02:15:48.4 0005 0002 0000 Parity/consistency initialization complete, volume: 3
0d 13:40:37.8 0006 0000 0000 Redundant operation state change.



CLI-1> Controller 1 (this_controller) is the current optimal path for these units:
show auto_path_change0
,1,3
Controller 2 (other_controller) is the current optimal path for these units:
2,4,5,6
Implicit (automatic load-based) LUN ownership changes are currently ENABLED.


CLI-1> Implicit (automatic load-based) LUN ownership changes are currently ENABLED.
Implicit LUN ownership change preferences are as follows:
Minimum % of proxied requests to trigger implicit path change..: 75%
Minimum number of requests to LUN before path change enabled...: 65536
Minimum time to wait before changing ownership after power-up..: 30 minutes
Minimum time between ownership changes for LUN.................: 30 minutes


### END LOG - DATE: 090715, TIME: 113343 ###
3 REPLIES 3
Wickedsunny
Valued Contributor

Re: MSA1500 flashing like christmas tree but with no obvious error in logs

All looks hail & hearty..

Sunny
Stephen Delaney
Occasional Visitor

Re: MSA1500 flashing like christmas tree but with no obvious error in logs

sorted it.

I ran the 'locate bus * time=*' command and it stopped the flashing LEDS, re-ran the command a couple of times per bus to see if it wasn't a fluke and all the LEDs are back to normal..

...strange one.
Wickedsunny
Valued Contributor

Re: MSA1500 flashing like christmas tree but with no obvious error in logs

For me too...

Good to know it works now.

Cheers,
Sunny