- Community Home
- >
- Storage
- >
- Entry Storage Systems
- >
- MSA Storage
- >
- More help.. Qlogic, MSA1000, SecurPath, help...
Categories
Company
Local Language
Forums
Discussions
Forums
- Data Protection and Retention
- Entry Storage Systems
- Legacy
- Midrange and Enterprise Storage
- Storage Networking
- HPE Nimble Storage
Discussions
Discussions
Discussions
Forums
Forums
Discussions
Discussion Boards
Discussion Boards
Discussion Boards
Discussion Boards
- BladeSystem Infrastructure and Application Solutions
- Appliance Servers
- Alpha Servers
- BackOffice Products
- Internet Products
- HPE 9000 and HPE e3000 Servers
- Networking
- Netservers
- Secure OS Software for Linux
- Server Management (Insight Manager 7)
- Windows Server 2003
- Operating System - Tru64 Unix
- ProLiant Deployment and Provisioning
- Linux-Based Community / Regional
- Microsoft System Center Integration
Discussion Boards
Discussion Boards
Discussion Boards
Discussion Boards
Discussion Boards
Discussion Boards
Discussion Boards
Discussion Boards
Discussion Boards
Discussion Boards
Discussion Boards
Discussion Boards
Discussion Boards
Discussion Boards
Discussion Boards
Discussion Boards
Discussion Boards
Discussion Boards
Discussion Boards
Discussion Boards
Discussion Boards
Discussion Boards
Community
Resources
Forums
Blogs
- Subscribe to RSS Feed
- Mark Topic as New
- Mark Topic as Read
- Float this Topic for Current User
- Bookmark
- Subscribe
- Printer Friendly Page
- Mark as New
- Bookmark
- Subscribe
- Mute
- Subscribe to RSS Feed
- Permalink
- Report Inappropriate Content
тАО12-15-2004 03:15 AM
тАО12-15-2004 03:15 AM
I have 5 servers connected to the switches. 3 of the servers have two Qlogic cards. The other two have one Qlogic card.
Ok.. the single connection server are listed in SSP (selective storage presentation) no problems. I have identified them by the FCID.
One of the servers with dual QL is available by both FCID (In SSP) and it appears redundant path is working (Install SecurePath on this box) and displayed the config.
The other two servers with two QL cards are only seen in SSP by one FCID. I have installed securepath on them but when I try to display it gives me an error. (cannot read config)
Any help is appreciated.
oh.. and I have looked in the switch config and I can see ALL the QL cards on their appropriate ports etc...
Thanks for any help...
--Steve
Solved! Go to Solution.
- Mark as New
- Bookmark
- Subscribe
- Mute
- Subscribe to RSS Feed
- Permalink
- Report Inappropriate Content
тАО12-15-2004 10:41 PM
тАО12-15-2004 10:41 PM
SolutionI would guess that the Dual QL server is the one where you are running ACU.
Have a look at my answer in this thread:
http://forums1.itrc.hp.com/service/forums/questionanswer.do?threadId=758229
If you run ACU on one of the other Dual QL servers, and go into the SSP config, you should see the 2nd HBA for that server. Repeat on the 3rd server. Then you should have all HBAs listed in SSP. Setup access for the HBAs, and see if SecurePath displays the info properly then.
Regards,
Stephen
- Mark as New
- Bookmark
- Subscribe
- Mute
- Subscribe to RSS Feed
- Permalink
- Report Inappropriate Content
тАО12-16-2004 05:16 AM
тАО12-16-2004 05:16 AM
Re: More help.. Qlogic, MSA1000, SecurPath, help...
Thanks for the help ! Looks good at this point
Happy Holidays !
--Steve
- Mark as New
- Bookmark
- Subscribe
- Mute
- Subscribe to RSS Feed
- Permalink
- Report Inappropriate Content
тАО12-17-2004 03:18 AM
тАО12-17-2004 03:18 AM
Re: More help.. Qlogic, MSA1000, SecurPath, help...
Just remember that is you lose Controller A, your hosts with only one HBA will lose all connectivity to your storage.
(Unless you have ISL'd the 2 SAN switches effectively making both controllers available to a single HBA. Not sure if this is a supported configuration.)
Steven
HP Master ASE, Storage, Servers, and Clustering
MCSE (NT 4.0, W2K, W2K3)
VCP (ESX2, Vi3, vSphere4, vSphere5, vSphere 6.x)
RHCE
NPP3 (Nutanix Platform Professional)
- Mark as New
- Bookmark
- Subscribe
- Mute
- Subscribe to RSS Feed
- Permalink
- Report Inappropriate Content
тАО12-17-2004 03:21 AM
тАО12-17-2004 03:21 AM
Re: More help.. Qlogic, MSA1000, SecurPath, help...
Thanks again !!! Really great support here and I will remember that when its time to purchase again ;)
Best,
--Steve
- Mark as New
- Bookmark
- Subscribe
- Mute
- Subscribe to RSS Feed
- Permalink
- Report Inappropriate Content
тАО12-17-2004 05:34 AM
тАО12-17-2004 05:34 AM
Re: More help.. Qlogic, MSA1000, SecurPath, help...
http://forums1.itrc.hp.com/service/forums/bizsupport/helptips.do?#28