- Community Home
- >
- Storage
- >
- Entry Storage Systems
- >
- MSA Storage
- >
- Re: Questions about SecurePath4 and Win2000Adv Clu...
MSA Storage
1752805
Members
5536
Online
108789
Solutions
Forums
Categories
Company
Local Language
back
Forums
Discussions
Forums
- Data Protection and Retention
- Entry Storage Systems
- Legacy
- Midrange and Enterprise Storage
- Storage Networking
- HPE Nimble Storage
Discussions
Discussions
Discussions
Forums
Discussions
back
Discussion Boards
Discussion Boards
Discussion Boards
Discussion Boards
- BladeSystem Infrastructure and Application Solutions
- Appliance Servers
- Alpha Servers
- BackOffice Products
- Internet Products
- HPE 9000 and HPE e3000 Servers
- Networking
- Netservers
- Secure OS Software for Linux
- Server Management (Insight Manager 7)
- Windows Server 2003
- Operating System - Tru64 Unix
- ProLiant Deployment and Provisioning
- Linux-Based Community / Regional
- Microsoft System Center Integration
Discussion Boards
Discussion Boards
Discussion Boards
Discussion Boards
Discussion Boards
Discussion Boards
Discussion Boards
Discussion Boards
Discussion Boards
Discussion Boards
Discussion Boards
Discussion Boards
Discussion Boards
Discussion Boards
Discussion Boards
Discussion Boards
Discussion Boards
Discussion Boards
Discussion Boards
Blogs
Information
Community
Resources
Community Language
Language
Forums
Blogs
Topic Options
- Subscribe to RSS Feed
- Mark Topic as New
- Mark Topic as Read
- Float this Topic for Current User
- Bookmark
- Subscribe
- Printer Friendly Page
- Mark as New
- Bookmark
- Subscribe
- Mute
- Subscribe to RSS Feed
- Permalink
- Report Inappropriate Content
12-19-2002 12:55 AM
12-19-2002 12:55 AM
Questions about SecurePath4 and Win2000Adv Cluster
I have a trouble with Secure Path 4 in Cluster.
I tested with next hardware:
Two Proliants DL380
Two HBA 176479-B21 in each
One integrated+one 10/100 PCI NIC in each
Two Fibre Channel Storage Switch 8 380591-B21
MA6000 (One Model 2100 Controller Enclosure
Two HSG60 Controller w/256-MB cache (8.6L)
Two Cache Battery 135823-B21
Two Model 4214R Single Bus, Single Power )
I make HA/F 500 solution.
I create three volumes on MA6000
I setup Win 2000 Adv on each
Next I set Win2000 Sp2
Next set Secure Path.
In this conf. all working fine.
Next.
I setup Active Directory, Cluster Service on one node, again install Service Pack2 for Win2000.
I preserve original compaq drivers.
Second node is power off.
I run Secure Path 4.
I turn on Load Balansing Round-robin. And I see that status links changed from Active to Available. My volumes on MA6000 from on-line to unreadeble, simple I lost my SAN paths to Storage. Reboots node doesn't effect. Disks still unreadable.
If I disconnect and connect back optic cable from both GBIC then I can't get from failed state automaticaly. In this moment I lose control.
How I can get Secure Path 4 working fine in cluster with redundancy paths?
Best regards, Vladimir
I tested with next hardware:
Two Proliants DL380
Two HBA 176479-B21 in each
One integrated+one 10/100 PCI NIC in each
Two Fibre Channel Storage Switch 8 380591-B21
MA6000 (One Model 2100 Controller Enclosure
Two HSG60 Controller w/256-MB cache (8.6L)
Two Cache Battery 135823-B21
Two Model 4214R Single Bus, Single Power )
I make HA/F 500 solution.
I create three volumes on MA6000
I setup Win 2000 Adv on each
Next I set Win2000 Sp2
Next set Secure Path.
In this conf. all working fine.
Next.
I setup Active Directory, Cluster Service on one node, again install Service Pack2 for Win2000.
I preserve original compaq drivers.
Second node is power off.
I run Secure Path 4.
I turn on Load Balansing Round-robin. And I see that status links changed from Active to Available. My volumes on MA6000 from on-line to unreadeble, simple I lost my SAN paths to Storage. Reboots node doesn't effect. Disks still unreadable.
If I disconnect and connect back optic cable from both GBIC then I can't get from failed state automaticaly. In this moment I lose control.
How I can get Secure Path 4 working fine in cluster with redundancy paths?
Best regards, Vladimir
1 REPLY 1
- Mark as New
- Bookmark
- Subscribe
- Mute
- Subscribe to RSS Feed
- Permalink
- Report Inappropriate Content
03-02-2003 06:43 AM
03-02-2003 06:43 AM
Re: Questions about SecurePath4 and Win2000Adv Cluster
Vladimir,
The minimum supported SP for Secure Path 4.0 is SP3. I'm attaching a link to the HSG80/60 suport matrix. Please ensure that everything is up to the rev levels.
I don't think it's a secure path issue though. One way to test is to remove secure path or disable it, disconnect a fibre connection ( so that your OS does not see multiple paths to the same disks) and determine if it's a clustering issue. I don't know why you reisntalled SP2 though but that could have overwritten some drivers as well.
ftp://ftp.compaq.com/pub/solutions/enterprise/ha/haf500/HSG80.pdf
The minimum supported SP for Secure Path 4.0 is SP3. I'm attaching a link to the HSG80/60 suport matrix. Please ensure that everything is up to the rev levels.
I don't think it's a secure path issue though. One way to test is to remove secure path or disable it, disconnect a fibre connection ( so that your OS does not see multiple paths to the same disks) and determine if it's a clustering issue. I don't know why you reisntalled SP2 though but that could have overwritten some drivers as well.
ftp://ftp.compaq.com/pub/solutions/enterprise/ha/haf500/HSG80.pdf
The opinions expressed above are the personal opinions of the authors, not of Hewlett Packard Enterprise. By using this site, you accept the Terms of Use and Rules of Participation.
News and Events
Support
© Copyright 2024 Hewlett Packard Enterprise Development LP