- Community Home
- >
- Storage
- >
- Entry Storage Systems
- >
- MSA Storage
- >
- booting error on alpaserver
Categories
Company
Local Language
Forums
Discussions
Forums
- Data Protection and Retention
- Entry Storage Systems
- Legacy
- Midrange and Enterprise Storage
- Storage Networking
- HPE Nimble Storage
Discussions
Discussions
Discussions
Forums
Forums
Discussions
Discussion Boards
Discussion Boards
Discussion Boards
Discussion Boards
- BladeSystem Infrastructure and Application Solutions
- Appliance Servers
- Alpha Servers
- BackOffice Products
- Internet Products
- HPE 9000 and HPE e3000 Servers
- Networking
- Netservers
- Secure OS Software for Linux
- Server Management (Insight Manager 7)
- Windows Server 2003
- Operating System - Tru64 Unix
- ProLiant Deployment and Provisioning
- Linux-Based Community / Regional
- Microsoft System Center Integration
Discussion Boards
Discussion Boards
Discussion Boards
Discussion Boards
Discussion Boards
Discussion Boards
Discussion Boards
Discussion Boards
Discussion Boards
Discussion Boards
Discussion Boards
Discussion Boards
Discussion Boards
Discussion Boards
Discussion Boards
Discussion Boards
Discussion Boards
Discussion Boards
Discussion Boards
Discussion Boards
Discussion Boards
Discussion Boards
Community
Resources
Forums
Blogs
- Subscribe to RSS Feed
- Mark Topic as New
- Mark Topic as Read
- Float this Topic for Current User
- Bookmark
- Subscribe
- Printer Friendly Page
- Mark as New
- Bookmark
- Subscribe
- Mute
- Subscribe to RSS Feed
- Permalink
- Report Inappropriate Content
тАО08-03-2006 04:50 AM
тАО08-03-2006 04:50 AM
booting error on alpaserver
I have a known working hardrive and all other hardware SCSI boards video boards etc tested in another Alph and known to be good.
I get this listed below.
>>>b dka0
(boot dka0.0.0.2000.0 -file vmunix -flags a)
block 0 of dka0.0.0.2000.0 is a valid boot block
reading 936 blocks from dka0.0.0.2000.0
bootstrap code read in
base = 200000, image_start = 0, image_bytes = 75000
initializing HWRPB at 2000
initializing page table at ff48000
initializing machine state
setting affinity to the primary CPU
jumping to bootstrap code
%APB-F-BADSYSROOT, System root does not exist, check bootflags
Is there a SYSA file that I need to edit to make the boot continue.
- Mark as New
- Bookmark
- Subscribe
- Mute
- Subscribe to RSS Feed
- Permalink
- Report Inappropriate Content
тАО08-03-2006 05:26 AM
тАО08-03-2006 05:26 AM
Re: booting error on alpaserver
would be the local root that the system tries to boot from. In most cases, however, the default root is . Try this:
>>> set os_type OpenVMS
>>> set boot_file
>>> set boot_osflags 0,0
>>> boot dka0
- Mark as New
- Bookmark
- Subscribe
- Mute
- Subscribe to RSS Feed
- Permalink
- Report Inappropriate Content
тАО08-04-2006 05:01 AM
тАО08-04-2006 05:01 AM
Re: booting error on alpaserver
I had another question: On booting Alpha servers.
After shutdown and power off then I powered back on again the system still comes back up to the >>> prompt I can manually load the boot commands and things work great.
Is there a system file I can edit and put these commands into to automaticly bring the system up without entering the operating system and boot commands by hand.
I am trying to build a spare unit I can ship to a remote location and have an operator install it for me. The automatic boot would be the way to go, so as not to have to manually load the commands.
Thanks.
- Mark as New
- Bookmark
- Subscribe
- Mute
- Subscribe to RSS Feed
- Permalink
- Report Inappropriate Content
тАО08-05-2006 07:30 PM
тАО08-05-2006 07:30 PM
Re: booting error on alpaserver
>>> set bootdef_dev dka0
Configure automatic boot:
>>> set auto_action boot
- Mark as New
- Bookmark
- Subscribe
- Mute
- Subscribe to RSS Feed
- Permalink
- Report Inappropriate Content
тАО08-08-2006 08:00 AM
тАО08-08-2006 08:00 AM