- Community Home
- >
- Storage
- >
- Entry Storage Systems
- >
- MSA Storage
- >
- msa1000 setup
MSA Storage
1753765
Members
5774
Online
108799
Solutions
Forums
Categories
Company
Local Language
юдл
back
Forums
Discussions
Forums
- Data Protection and Retention
- Entry Storage Systems
- Legacy
- Midrange and Enterprise Storage
- Storage Networking
- HPE Nimble Storage
Discussions
Discussions
Discussions
Forums
Forums
Discussions
юдл
back
Discussion Boards
Discussion Boards
Discussion Boards
Discussion Boards
- BladeSystem Infrastructure and Application Solutions
- Appliance Servers
- Alpha Servers
- BackOffice Products
- Internet Products
- HPE 9000 and HPE e3000 Servers
- Networking
- Netservers
- Secure OS Software for Linux
- Server Management (Insight Manager 7)
- Windows Server 2003
- Operating System - Tru64 Unix
- ProLiant Deployment and Provisioning
- Linux-Based Community / Regional
- Microsoft System Center Integration
Discussion Boards
Discussion Boards
Discussion Boards
Discussion Boards
Discussion Boards
Discussion Boards
Discussion Boards
Discussion Boards
Discussion Boards
Discussion Boards
Discussion Boards
Discussion Boards
Discussion Boards
Discussion Boards
Discussion Boards
Discussion Boards
Discussion Boards
Discussion Boards
Discussion Boards
Discussion Boards
Discussion Boards
Discussion Boards
Blogs
Information
Community
Resources
Community Language
Language
Forums
Blogs
Topic Options
- Subscribe to RSS Feed
- Mark Topic as New
- Mark Topic as Read
- Float this Topic for Current User
- Bookmark
- Subscribe
- Printer Friendly Page
- Mark as New
- Bookmark
- Subscribe
- Mute
- Subscribe to RSS Feed
- Permalink
- Report Inappropriate Content
тАО03-13-2006 08:45 AM
тАО03-13-2006 08:45 AM
msa1000 setup
I have setup my msa1000. From the one server that has the hba installed i can see the controller and have configured two logical drives from the array.
How do i see the volumes from the server that it is attached to.
When i try to run san surfer express it says that the san is not attached, but i have configured it using the acu
any ideas ?
How do i see the volumes from the server that it is attached to.
When i try to run san surfer express it says that the san is not attached, but i have configured it using the acu
any ideas ?
3 REPLIES 3
- Mark as New
- Bookmark
- Subscribe
- Mute
- Subscribe to RSS Feed
- Permalink
- Report Inappropriate Content
тАО03-13-2006 09:03 AM
тАО03-13-2006 09:03 AM
Re: msa1000 setup
What HBA do you use?
SANSurfer express is only for QLogic-based HBAs (such as FCA2214).
SANSurfer express is only for QLogic-based HBAs (such as FCA2214).
- Mark as New
- Bookmark
- Subscribe
- Mute
- Subscribe to RSS Feed
- Permalink
- Report Inappropriate Content
тАО03-13-2006 09:05 AM
тАО03-13-2006 09:05 AM
Re: msa1000 setup
Disk Adminisrator, initilize and Create Primary or extended partition, Format and use.
JPL
JPL
- Mark as New
- Bookmark
- Subscribe
- Mute
- Subscribe to RSS Feed
- Permalink
- Report Inappropriate Content
тАО03-13-2006 09:43 AM
тАО03-13-2006 09:43 AM
Re: msa1000 setup
I am using the q200 hba which come in the starter kit.
when i open disk administrator the san drive is not there , although i can see the logical drives within the acu.
when i open disk administrator the san drive is not there , although i can see the logical drives within the acu.
The opinions expressed above are the personal opinions of the authors, not of Hewlett Packard Enterprise. By using this site, you accept the Terms of Use and Rules of Participation.
News and Events
Support
© Copyright 2024 Hewlett Packard Enterprise Development LP