MSA Storage
cancel
Showing results for 
Search instead for 
Did you mean: 

msa1500 a/a add new hba connection

 
Thierry W
Occasional Contributor

msa1500 a/a add new hba connection

Hi,
i have 2 proliant (Suse Linux, OES2) connected each with 2 emulex HBA (FC2143) for multipathing.
Recently i changed one of my hba on one server.
Everything went fine, hba view by system (HBAnyware) but first i cannot remove old connection from MSA (give me unknown connection but don't want to delete her), second when i create my new connection the controller's statut directive are not set..
show tech_support report that the controller2 port1 is offline. So is the offline controller reporting as something todo with my problem ? or do i have to reboot my MSA ? in this case is it possible to just do an : disable this_controller then reenable it (how ?)
Thanks

Below show tech_support result :
show tech_support

CLI-1> show version -all
MSA1500 Firmware Revision: 7.00b1500 (SGA073004K)
Build Time: 2007-01-24 16:13:17
MSA1500 Hardware Revision: a
Fibre Module AutoRev: 0x020000
SCSI I/O Module Bus 0 Revision: 2.02
SCSI I/O Module Bus 1 Revision: 2.02
SCSI I/O Module Bus 2 Revision: <>
SCSI I/O Module Bus 3 Revision: <>
Fan Control Module A Revision: 2.38
Fan Control Module B Revision: 2.38
Box 1 PROLIANT 4LEE Rev: CP20 (MBRZLMPX9D)
Box 2 PROLIANT 8LCE Rev: 2.02 (E0W5MLJ16C)
Box 2 Fan Control Module A Rev: 2.38
Box 2 Fan Control Module B Rev: 2.38

Disk Drives:
B T L BOX BAY GB Model Rev. Serial No.
0 0 0 1 1 300.0 COMPAQ BD3008A4C6 HPB4 3KR4F17N000098096DP0
0 1 0 1 2 300.0 COMPAQ BD3008A4C6 HPB4 3KR46J6000009806980C
0 2 0 1 3 300.0 COMPAQ BD3008A4C6 HPB4 3KR46KG40000980819Z0
0 3 0 1 4 300.0 COMPAQ BD3008A4C6 HPB4 3KR4ET3V000098084DKW
0 4 0 1 5 300.0 COMPAQ BD3008A4C6 HPB4 3KR4F8FZ000098096EEV
0 5 0 1 6 300.0 COMPAQ BD3008A4C6 HPB4 3KR49VEB00009809WUJV
0 8 0 1 7 300.0 COMPAQ BF30084971 HPB7
0 9 0 1 8 300.0 COMPAQ BF30084971 HPB7
0 10 0 1 9 300.0 COMPAQ BF30084971 HPB7
0 11 0 1 10 300.0 COMPAQ BF30084971 HPB7
1 3 1 2 1 500.0 Maxtor 6H500F0 HA431DD H80DRDDH
1 3 2 2 2 500.0 Maxtor 6H500F0 HA431DD H80EJCJH
1 3 3 2 3 500.0 Maxtor 6H500F0 HA431BR H807FWYH
1 3 4 2 4 500.0 Maxtor 6H500F0 HA431DD H80E6W0H
1 3 5 2 5 500.0 Maxtor 6H500F0 HA431DD H80E3QTH
1 3 6 2 6 500.0 Seagate ST3500641AS 3.AJJ
1 3 7 2 7 500.0 Unknown GB0500C4413 HPG 9QG3WK1E
1 3 8 2 8 500.0 Unknown GB0500C4413 HPG 9QG3ZDFE
1 3 9 2 9 500.0 Unknown GB0500C4413 HPG 9QG3X3TM
1 3 10 2 10 500.0 Unknown GB0500C4413 HPG 9QG3ZD03
1 3 11 2 11 500.0 Unknown GB0500C4413 HPG 9QG3ZDCC
1 3 12 2 12 500.0 Unknown GB0500C4413 HPG 9QG3ZDA9


CLI-1> show profile
Profile name = Default (Default) Mode value = (00002405)

Mode 0 = Peripheral Device LUN Addressing
Mode 1 = Legacy Failover
Mode 2 = Logical volumes connect as available on Backup Controller
Mode 3 = Product ID of 'MSA1000 VOLUME' (only if Active-Standby mode)
Mode 4 = Normal bad block handling
Mode 5 = Logout selected initiators on TPRLO
Mode 6 = Fault management events not reported through Unit Attention
Mode 7 = Do not send FCP response info with SCSI status
Mode 8 = Do not send Unit Attention on failover
Mode 9 = SCSI inquiry revision field contains the actual version
Mode 10 = SCSI inquiry vendor ID='HP'
Mode 11 = Power On Reset Unit Attention generated on FC Login or Logout
Mode 12 = Ignore Force Unit Access on Write
Mode 13 = Admit Target Port on Reservation
Mode 14 = Asymmetrical Active/Active Operating Mode

Profile name = Windows
Type = Standard Mode value = (00002405)

Mode 0 = Peripheral Device LUN Addressing
Mode 1 = Legacy Failover
Mode 2 = Logical volumes connect as available on Backup Controller
Mode 3 = Product ID of 'MSA1000 VOLUME' (only if Active-Standby mode)
Mode 4 = Normal bad block handling
Mode 5 = Logout selected initiators on TPRLO
Mode 6 = Fault management events not reported through Unit Attention
Mode 7 = Do not send FCP response info with SCSI status
Mode 8 = Do not send Unit Attention on failover
Mode 9 = SCSI inquiry revision field contains the actual version
Mode 10 = SCSI inquiry vendor ID='HP'
Mode 11 = Power On Reset Unit Attention generated on FC Login or Logout
Mode 12 = Ignore Force Unit Access on Write
Mode 13 = Admit Target Port on Reservation
Mode 14 = Asymmetrical Active/Active Operating Mode

Profile name = Windows (degraded performance)
Type = Standard Mode value = (00003405)

Mode 0 = Peripheral Device LUN Addressing
Mode 1 = Legacy Failover
Mode 2 = Logical volumes connect as available on Backup Controller
Mode 3 = Product ID of 'MSA1000 VOLUME' (only if Active-Standby mode)
Mode 4 = Normal bad block handling
Mode 5 = Logout selected initiators on TPRLO
Mode 6 = Fault management events not reported through Unit Attention
Mode 7 = Do not send FCP response info with SCSI status
Mode 8 = Do not send Unit Attention on failover
Mode 9 = SCSI inquiry revision field contains the actual version
Mode 10 = SCSI inquiry vendor ID='HP'
Mode 11 = Power On Reset Unit Attention generated on FC Login or Logout
Mode 12 = Enforce Force Unit Access on Write
Mode 13 = Admit Target Port on Reservation
Mode 14 = Asymmetrical Active/Active Operating Mode

Profile name = OpenVMS
Type = Standard Mode value = (00003473)

Mode 0 = Peripheral Device LUN Addressing
Mode 1 = Asymmetric Failover
Mode 2 = Logical volumes connect as unavailable on Backup Controller
Mode 3 = Product ID of 'MSA1000 VOLUME' (only if Active-Standby mode)
Mode 4 = VMS shadow style bad block handling
Mode 5 = Logout all initiators on TPRLO
Mode 6 = Fault management events reported through Unit Attention
Mode 7 = Do not send FCP response info with SCSI status
Mode 8 = Do not send Unit Attention on failover
Mode 9 = SCSI inquiry revision field contains the actual version
Mode 10 = SCSI inquiry vendor ID='HP'
Mode 11 = Power On Reset Unit Attention generated on FC Login or Logout
Mode 12 = Enforce Force Unit Access on Write
Mode 13 = Admit Target Port on Reservation
Mode 14 = Asymmetrical Active/Active Operating Mode

Profile name = Tru64
Type = Standard Mode value = (00003563)

Mode 0 = Peripheral Device LUN Addressing
Mode 1 = Asymmetric Failover
Mode 2 = Logical volumes connect as unavailable on Backup Controller
Mode 3 = Product ID of 'MSA1000 VOLUME' (only if Active-Standby mode)
Mode 4 = Normal bad block handling
Mode 5 = Logout all initiators on TPRLO
Mode 6 = Fault management events reported through Unit Attention
Mode 7 = Do not send FCP response info with SCSI status
Mode 8 = Send Unit Attention on failover
Mode 9 = SCSI inquiry revision field contains the actual version
Mode 10 = SCSI inquiry vendor ID='HP'
Mode 11 = Power On Reset Unit Attention generated on FC Login or Logout
Mode 12 = Enforce Force Unit Access on Write
Mode 13 = Admit Target Port on Reservation
Mode 14 = Asymmetrical Active/Active Operating Mode

Profile name = Linux
Type = Standard Mode value = (000034a7)

Mode 0 = Peripheral Device LUN Addressing
Mode 1 = Asymmetric Failover
Mode 2 = Logical volumes connect as available on Backup Controller
Mode 3 = Product ID of 'MSA1000 VOLUME' (only if Active-Standby mode)
Mode 4 = Normal bad block handling
Mode 5 = Logout all initiators on TPRLO
Mode 6 = Fault management events not reported through Unit Attention
Mode 7 = Send FCP response info with SCSI status
Mode 8 = Do not send Unit Attention on failover
Mode 9 = SCSI inquiry revision field contains the actual version
Mode 10 = SCSI inquiry vendor ID='HP'
Mode 11 = Power On Reset Unit Attention generated on FC Login or Logout
Mode 12 = Enforce Force Unit Access on Write
Mode 13 = Admit Target Port on Reservation
Mode 14 = Asymmetrical Active/Active Operating Mode

Profile name = Solaris
Type = Standard Mode value = (000034a7)

Mode 0 = Peripheral Device LUN Addressing
Mode 1 = Asymmetric Failover
Mode 2 = Logical volumes connect as available on Backup Controller
Mode 3 = Product ID of 'MSA1000 VOLUME' (only if Active-Standby mode)
Mode 4 = Normal bad block handling
Mode 5 = Logout all initiators on TPRLO
Mode 6 = Fault management events not reported through Unit Attention
Mode 7 = Send FCP response info with SCSI status
Mode 8 = Do not send Unit Attention on failover
Mode 9 = SCSI inquiry revision field contains the actual version
Mode 10 = SCSI inquiry vendor ID='HP'
Mode 11 = Power On Reset Unit Attention generated on FC Login or Logout
Mode 12 = Enforce Force Unit Access on Write
Mode 13 = Admit Target Port on Reservation
Mode 14 = Asymmetrical Active/Active Operating Mode

Profile name = Netware
Type = Standard Mode value = (000034a7)

Mode 0 = Peripheral Device LUN Addressing
Mode 1 = Asymmetric Failover
Mode 2 = Logical volumes connect as available on Backup Controller
Mode 3 = Product ID of 'MSA1000 VOLUME' (only if Active-Standby mode)
Mode 4 = Normal bad block handling
Mode 5 = Logout all initiators on TPRLO
Mode 6 = Fault management events not reported through Unit Attention
Mode 7 = Send FCP response info with SCSI status
Mode 8 = Do not send Unit Attention on failover
Mode 9 = SCSI inquiry revision field contains the actual version
Mode 10 = SCSI inquiry vendor ID='HP'
Mode 11 = Power On Reset Unit Attention generated on FC Login or Logout
Mode 12 = Enforce Force Unit Access on Write
Mode 13 = Admit Target Port on Reservation
Mode 14 = Asymmetrical Active/Active Operating Mode

Profile name = HP
Type = Standard Mode value = (00003ca6)

Mode 0 = Volume Set Addressing
Mode 1 = Asymmetric Failover
Mode 2 = Logical volumes connect as available on Backup Controller
Mode 3 = Product ID of 'MSA1000 VOLUME' (only if Active-Standby mode)
Mode 4 = Normal bad block handling
Mode 5 = Logout all initiators on TPRLO
Mode 6 = Fault management events not reported through Unit Attention
Mode 7 = Send FCP response info with SCSI status
Mode 8 = Do not send Unit Attention on failover
Mode 9 = SCSI inquiry revision field contains the actual version
Mode 10 = SCSI inquiry vendor ID='HP'
Mode 11 = No Power On Reset Unit Attention generated on FC Login or Logout
Mode 12 = Enforce Force Unit Access on Write
Mode 13 = Admit Target Port on Reservation
Mode 14 = Asymmetrical Active/Active Operating Mode

Profile name = XP Storage Array
Type = Standard Mode value = (00003563)

Mode 0 = Peripheral Device LUN Addressing
Mode 1 = Asymmetric Failover
Mode 2 = Logical volumes connect as unavailable on Backup Controller
Mode 3 = Product ID of 'MSA1000 VOLUME' (only if Active-Standby mode)
Mode 4 = Normal bad block handling
Mode 5 = Logout all initiators on TPRLO
Mode 6 = Fault management events reported through Unit Attention
Mode 7 = Do not send FCP response info with SCSI status
Mode 8 = Send Unit Attention on failover
Mode 9 = SCSI inquiry revision field contains the actual version
Mode 10 = SCSI inquiry vendor ID='HP'
Mode 11 = Power On Reset Unit Attention generated on FC Login or Logout
Mode 12 = Enforce Force Unit Access on Write
Mode 13 = Admit Target Port on Reservation
Mode 14 = Asymmetrical Active/Active Operating Mode

Profile name = oes
Type = Custom Mode value = (00000000)

Mode 0 = Volume Set Addressing
Mode 1 = Legacy Failover
Mode 2 = Logical volumes connect as unavailable on Backup Controller
Mode 3 = Product ID of 'MSA1000 VOLUME' (only if Active-Standby mode)
Mode 4 = Normal bad block handling
Mode 5 = Logout selected initiators on TPRLO
Mode 6 = Fault management events not reported through Unit Attention
Mode 7 = Do not send FCP response info with SCSI status
Mode 8 = Do not send Unit Attention on failover
Mode 9 = SCSI inquiry revision field contains the actual version
Mode 10 = SCSI inquiry vendor ID='Compaq'
Mode 11 = Power On Reset Unit Attention generated on FC Login or Logout
Mode 12 = Ignore Force Unit Access on Write
Mode 13 = Ignore Target Port on Reservation
Mode 14 = Asymmetrical Active/Active Operating Mode

Profile name = mrbig
Type = Custom Mode value = (00000048)

Mode 0 = Volume Set Addressing
Mode 1 = Legacy Failover
Mode 2 = Logical volumes connect as unavailable on Backup Controller
Mode 3 = Product ID of 'LOGICAL VOLUME' (only if Active-Standby mode)
Mode 4 = Normal bad block handling
Mode 5 = Logout selected initiators on TPRLO
Mode 6 = Fault management events reported through Unit Attention
Mode 7 = Do not send FCP response info with SCSI status
Mode 8 = Do not send Unit Attention on failover
Mode 9 = SCSI inquiry revision field contains the actual version
Mode 10 = SCSI inquiry vendor ID='Compaq'
Mode 11 = Power On Reset Unit Attention generated on FC Login or Logout
Mode 12 = Ignore Force Unit Access on Write
Mode 13 = Ignore Target Port on Reservation
Mode 14 = Asymmetrical Active/Active Operating Mode

Profile name = mrsbig
Type = Custom Mode value = (00000000)

Mode 0 = Volume Set Addressing
Mode 1 = Legacy Failover
Mode 2 = Logical volumes connect as unavailable on Backup Controller
Mode 3 = Product ID of 'MSA1000 VOLUME' (only if Active-Standby mode)
Mode 4 = Normal bad block handling
Mode 5 = Logout selected initiators on TPRLO
Mode 6 = Fault management events not reported through Unit Attention
Mode 7 = Do not send FCP response info with SCSI status
Mode 8 = Do not send Unit Attention on failover
Mode 9 = SCSI inquiry revision field contains the actual version
Mode 10 = SCSI inquiry vendor ID='Compaq'
Mode 11 = Power On Reset Unit Attention generated on FC Login or Logout
Mode 12 = Ignore Force Unit Access on Write
Mode 13 = Ignore Target Port on Reservation
Mode 14 = Asymmetrical Active/Active Operating Mode


CLI-1> show globals

Global Parameters:
System Name: MSA1500
Rebuild Priority: medium
Expand Priority: medium
Surface Delay: 3.0 seconds

Total Cache: 256MB
50% Read Cache: 128MB
50% Write Cache: 128MB

Temperature:
EMU: 35 Celsius, 95 Fahrenheit
PS1: 33 Celsius, 91 Fahrenheit
PS2: 33 Celsius, 91 Fahrenheit

CLI-1> show acl

ACL is enabled:
Connection WWPN Units
1-Droite 10000000-C989D38E 0, 1, 2
2-Gauche 10000000-C969B231 0, 1, 2
2-Gauche 10000000-C969B405 0, 1, 2
matrix 500110A0-0016E262 4
1-Droite 10000000-C969B458 0, 1, 2
Inaccessible Units: None

CLI-1> show connections

Connection Name: 1-Droite
Host WWNN = 20000000-C969B458
Host WWPN = 10000000-C969B458
Profile Name = Linux
Unit Offset = 0
Controller 1 Port 1 Status = Online
Controller 2 Port 1 Status = Offline

Connection Name: 2-Gauche
Host WWNN = 20000000-C969B231
Host WWPN = 10000000-C969B231
Profile Name = Linux
Unit Offset = 0
Controller 1 Port 1 Status = Offline
show disks Controller 2 Port 1 Status = Online


Connection Name: 2-Gauche
Host WWNN = 20000000-C969B405
Host WWPN = 10000000-C969B405
Profile Name = Linux
Unit Offset = 0
Controller 1 Port 1 Status = Offline
Disk List: (box,bay) (B:T:L) Size Speed Units
show boxEnclosure 1: SCSI (0:06:00) PROLIANT 4LEE CP20

Disk101 (1,01) (0:00:00) 300.0GB 160 MB/s 2, 4 (spare)
Disk102 (1,02) (0:01:00) 300.0GB 160 MB/s 2
Disk103 (1,03) (0:02:00) 300.0GB 160 MB/s 2
Disk104 (1,04) (0:03:00) 300.0GB 160 MB/s 2
Disk105 (1,05) (0:04:00) 300.0GB 160 MB/s 2
Disk106 (1,06) (0:05:00) 300.0GB 160 MB/s 2
Disk107 (1,07) (0:08:00) 300.0GB 160 MB/s 4
Disk108 (1,08) (0:09:00) 300.0GB 160 MB/s 4
Disk109 (1,09) (0:10:00) 300.0GB 160 MB/s 4
Disk110 (1,10) (0:11:00) 300.0GB 160 MB/s 4
Enclosure 2: SATA (1:03:00) PROLIANT 8LCE 2.02
Disk201 (2,01) (1:03:01) 500.0GB 160 MB/s 0
Disk202 (2,02) (1:03:02) 500.0GB 160 MB/s 0
Disk203 (2,03) (1:03:03) 500.0GB 160 MB/s 0
Disk204 (2,04) (1:03:04) 500.0GB 160 MB/s 0
Disk205 (2,05) (1:03:05) 500.0GB 160 MB/s 0
Disk206 (2,06) (1:03:06) 500.0GB 160 MB/s 0
Disk207 (2,07) (1:03:07) 500.0GB 160 MB/s 1
Disk208 (2,08) (1:03:08) 500.0GB 160 MB/s 1
Disk209 (2,09) (1:03:09) 500.0GB 160 MB/s 1
Disk210 (2,10) (1:03:10) 500.0GB 160 MB/s 1
Disk211 (2,11) (1:03:11) 500.0GB 160 MB/s 0, 1 (spare)
Disk212 (2,12) (1:03:12) 500.0GB 160 MB/s 0, 1 (spare)

Notes:
The speed is the currently negotiated speed to the disk. This may
be less than the maximum speed supported by the device due to bus
faults, loss of signal integrity, etc.
Box #1:
SCSI enclosure at bus 0 channel 0 target 6
Firmware ID string: PROLIANT 4LEE
Firmware revision: CP20
Serial number: MBRZLMPX9D
Environmental Status:
No alert conditions reported

Box #2:
SATA enclosure at bus 1 channel 0 target 3
Firmware ID string: PROLIANT 8LCE
Firmware revision: 2.02
Serial number: E0W5MLJ16C
Environmental Status:
No alert conditions reported
Cache Information:
Total Memory: 112MB
Read Cache: 56MB
Write Cache: 56MB
Cache Status: Enabled
Battery #1 (lower): OK
Battery #2 (upper): OK
Controller 2 Port 1 Status = Online

Connection Name: matrix
Host WWNN = 500110A0-0016E263
Host WWPN = 500110A0-0016E262
Profile Name = Linux
Unit Offset = 0
Controller 1 Port 1 Status = Offline
show units Controller 2 Port 1 Status = Online


Connection Name:
Host WWNN = 20000000-C969BA01
Host WWPN = 10000000-C969BA01
Profile Name = Default
Unit Offset = 0
Controller 1 Port 1 Status = Online

Unit 0:
show this_controllerIn PDLA mode, Unit 0 is Lun 1; In VSA mode, Unit 0 is Lun 0.

Unit Identifier :
Device Identifier : 600508B3-0094F1D0-56F89989-F75B000A
Preferred Path : Controller 2 (other controller)
Cache Status : Enabled
Max Boot Partition: Enabled
Volume Status : VOLUME OK
Parity Init Status: Complete
6 Data Disk(s) used by lun 0:
Disk201: Box 2, Bay 01, (B:T:L 1:03:01)
Disk202: Box 2, Bay 02, (B:T:L 1:03:02)
Disk203: Box 2, Bay 03, (B:T:L 1:03:03)
Disk204: Box 2, Bay 04, (B:T:L 1:03:04)
Disk205: Box 2, Bay 05, (B:T:L 1:03:05)
Disk206: Box 2, Bay 06, (B:T:L 1:03:06)
Spare Disk(s) used by lun 0:
Disk211: Box 2, Bay 11, (B:T:L 1:03:11)
Disk212: Box 2, Bay 12, (B:T:L 1:03:12)
Logical Volume Raid Level: ADVANCED DATA GUARD (RAID 6)
stripe_size=64kB
Logical Volume Capacity : 1,907,624MB

Unit 1:
In PDLA mode, Unit 1 is Lun 2; In VSA mode, Unit 1 is Lun 1.
Unit Identifier :
Device Identifier : 600508B3-0094F1D0-36015A1A-7CE90003
Preferred Path : Controller 2 (other controller)
Cache Status : Enabled
Max Boot Partition: Enabled
Volume Status : VOLUME OK
Parity Init Status: Complete
4 Data Disk(s) used by lun 1:
Disk207: Box 2, Bay 07, (B:T:L 1:03:07)
Disk208: Box 2, Bay 08, (B:T:L 1:03:08)
Disk209: Box 2, Bay 09, (B:T:L 1:03:09)
Disk210: Box 2, Bay 10, (B:T:L 1:03:10)
Spare Disk(s) used by lun 1:
Disk211: Box 2, Bay 11, (B:T:L 1:03:11)
Disk212: Box 2, Bay 12, (B:T:L 1:03:12)
Logical Volume Raid Level: DISTRIBUTED PARITY FAULT TOLERANCE (RAID 5)
stripe_size=64kB
Logical Volume Capacity : 1,430,718MB

Unit 2:
In PDLA mode, Unit 2 is Lun 3; In VSA mode, Unit 2 is Lun 2.
Unit Identifier :
Device Identifier : 600508B3-0094F1D0-AF61B751-A2DB000B
Preferred Path : Controller 2 (other controller)
Cache Status : Enabled
Max Boot Partition: Disabled
Volume Status : VOLUME OK
Parity Init Status: Complete
5 Data Disk(s) used by lun 2:
Disk102: Box 1, Bay 02, (B:T:L 0:01:00)
Disk103: Box 1, Bay 03, (B:T:L 0:02:00)
Disk104: Box 1, Bay 04, (B:T:L 0:03:00)
Disk105: Box 1, Bay 05, (B:T:L 0:04:00)
Disk106: Box 1, Bay 06, (B:T:L 0:05:00)
Spare Disk(s) used by lun 2:
Disk101: Box 1, Bay 01, (B:T:L 0:00:00)
Logical Volume Raid Level: ADVANCED DATA GUARD (RAID 6)
stripe_size=64kB
Logical Volume Capacity : 858,305MB

Unit 4:
In PDLA mode, Unit 4 is Lun 5; In VSA mode, Unit 4 is Lun 4.
Unit Identifier :
Device Identifier : 600508B3-0094F1D0-43CE4C5A-A818000C
Preferred Path : Controller 1 (this controller)
Cache Status : Enabled
Max Boot Partition: Enabled
Volume Status : VOLUME OK
Parity Init Status: Complete
4 Data Disk(s) used by lun 4:
Disk107: Box 1, Bay 07, (B:T:L 0:08:00)
Disk108: Box 1, Bay 08, (B:T:L 0:09:00)
Disk109: Box 1, Bay 09, (B:T:L 0:10:00)
Disk110: Box 1, Bay 10, (B:T:L 0:11:00)
Spare Disk(s) used by lun 4:
Disk101: Box 1, Bay 01, (B:T:L 0:00:00)
Logical Volume Raid Level: DISTRIBUTED PARITY FAULT TOLERANCE (RAID 5)
stripe_size=64kB
Logical Volume Capacity : 858,300MB
Controller 1 (right controller):
MSA1500(c) Hewlett-Packard PB9840TX3UZ0DT Version 7.00 Build 1500 Hardware A
Build Time: 2007-01-24 16:13:17
Component Enclosure.
Controller Identifier: MSA-1
NODE_ID = 500508B3-0094F1D0
SCSI_VERSION = SCSI-3
Supported Redundancy Mode: Active/Standby Asym-Active/Active
Current Redundancy Mode: Asym-Active/Active
Device Port SCSI address 6
Terminal speed for the CLI is set to 19200.
Host Port_1:
REPORTED PORT_ID 500508B3-0094F1D1
PORT_1_TOPOLOGY = F_Port
Cache:
128 megabyte read cache 128 megabyte write cache Version 2
Cache is GOOD, and Cache is enabled.
Unflushed data in cache
Batteries are enabled
Module #1 is fully charged and turned on.
Controller Up Time:
41 Days 00 Hours 58 Minutes 58 Seconds
Health:
Surface Scan: Complete.
Rebuild Status: Complete.
Expansion: Complete.
Controller 2 Port 1 Status = Offline

Connection Name: 1-Droite
Host WWNN = 20000000-C989D38E
Host WWPN = 10000000-C989D38E
Profile Name = Linux
Unit Offset = 0
show other_controller

CLI-1> Controller 2 (left controller):
MSA1500(c) Hewlett-Packard PB9840TX3UZ00R Version 7.00 Build 1500 Hardware A
Build Time: 2007-01-24 16:13:17
Component Enclosure.
Controller Identifier: MSA-2
NODE_ID = 500508B3-0094F1D0
SCSI_VERSION = SCSI-3
Supported Redundancy Mode: Active/Standby Asym-Active/Active
Current Redundancy Mode: Asym-Active/Active
Device Port SCSI address 7
Terminal speed for the CLI is set to 19200.
Host Port_1:
REPORTED PORT_ID 500508B3-0094F1D9
PORT_1_TOPOLOGY = F_Port
Cache:
128 megabyte read cache 128 megabyte write cache Version 2
Cache is GOOD, and Cache is enabled.
No unflushed data in cache
Batteries are disabled
Module #1 is fully charged and turned off.
Controller Up Time:
41 Days 00 Hours 27 Minutes 02 Seconds
Health:
Surface Scan: Complete.
Rebuild Status: Complete.
Expansion: Complete.
show eventlog
TIME CLASS SUB DETL MESSAGE

CLI-1> 0d 00:04:54.1 0006 0000 0000 Redundant operation state change.
show preferred_path2d 05:30:48.7 0006 0000 0000 Redundant operation state change.

2d 21:53:42.2 0006 0000 0000 Redundant operation state change.
4d 02:26:56.0 0006 0000 0000 Redundant operation state change.



CLI-1> Controller 1 (this_controller) is the current optimal path for these units:
show auto_path_change4

Controller 2 (other_controller) is the current optimal path for these units:
0,1,2
Implicit (automatic load-based) LUN ownership changes are currently ENABLED.


CLI-1> Implicit (automatic load-based) LUN ownership changes are currently ENABLED.
Implicit LUN ownership change preferences are as follows:
Minimum % of proxied requests to trigger implicit path change..: 75%
Minimum number of requests to LUN before path change enabled...: 65536
Minimum time to wait before changing ownership after power-up..: 30 minutes
Minimum time between ownership changes for LUN.................: 30 minutes


CLI-1>
1 REPLY 1
Thierry W
Occasional Contributor

Re: msa1500 a/a add new hba connection

I reply to myself, i had to revalidate zoning in my switch to use my new HBA
However The problem for deleting connection still remain..restart controller ?