- Community Home
- >
- Servers and Operating Systems
- >
- Operating Systems
- >
- Operating System - HP-UX
- >
- Re: Qpopper and shadow password : password incorre...
Categories
Company
Local Language
Forums
Discussions
Forums
- Data Protection and Retention
- Entry Storage Systems
- Legacy
- Midrange and Enterprise Storage
- Storage Networking
- HPE Nimble Storage
Discussions
Discussions
Discussions
Forums
Forums
Discussions
Discussion Boards
Discussion Boards
Discussion Boards
Discussion Boards
- BladeSystem Infrastructure and Application Solutions
- Appliance Servers
- Alpha Servers
- BackOffice Products
- Internet Products
- HPE 9000 and HPE e3000 Servers
- Networking
- Netservers
- Secure OS Software for Linux
- Server Management (Insight Manager 7)
- Windows Server 2003
- Operating System - Tru64 Unix
- ProLiant Deployment and Provisioning
- Linux-Based Community / Regional
- Microsoft System Center Integration
Discussion Boards
Discussion Boards
Discussion Boards
Discussion Boards
Discussion Boards
Discussion Boards
Discussion Boards
Discussion Boards
Discussion Boards
Discussion Boards
Discussion Boards
Discussion Boards
Discussion Boards
Discussion Boards
Discussion Boards
Discussion Boards
Discussion Boards
Discussion Boards
Discussion Boards
Discussion Boards
Discussion Boards
Discussion Boards
Community
Resources
Forums
Blogs
- Subscribe to RSS Feed
- Mark Topic as New
- Mark Topic as Read
- Float this Topic for Current User
- Bookmark
- Subscribe
- Printer Friendly Page
- Mark as New
- Bookmark
- Subscribe
- Mute
- Subscribe to RSS Feed
- Permalink
- Report Inappropriate Content
тАО06-06-2005 01:15 AM
тАО06-06-2005 01:15 AM
on hpux B11.11 with /etc/shadow password (ShadowPW.SHADOW B11.11.02 from hp software depot)qpopper 4.0.5 or 4.0.8 failed with message : -ERR [AUTH] Password supplied for "joel" is incorrect.
Compile with ./configure --enable-specialauth dont correct this.
Qpopper was ok before shadow password.
Has anybody been successfull with qpopper and shadow password on HP-UX?
Thanks
Solved! Go to Solution.
- Mark as New
- Bookmark
- Subscribe
- Mute
- Subscribe to RSS Feed
- Permalink
- Report Inappropriate Content
тАО06-06-2005 01:32 AM
тАО06-06-2005 01:32 AM
Re: Qpopper and shadow password : password incorrect
Sometimes the conversion to shadow password locks the user id. Actually the user was probably locked prior to the conversion.
I recommend the user password be reset and you check the user with sam be checked for how many bad logins are allowed prior to lock.
$1 is in this case the username.
/usr/lbin/modprpw -l -k $1
SEP
http://www.isnamerica.com/contactsep.shtml
Owner of ISN Corporation
http://isnamerica.com
http://hpuxconsulting.com
Sponsor: http://hpux.ws
Twitter: http://twitter.com/hpuxlinux
Founder http://newdatacloud.com
- Mark as New
- Bookmark
- Subscribe
- Mute
- Subscribe to RSS Feed
- Permalink
- Report Inappropriate Content
тАО06-06-2005 01:57 AM
тАО06-06-2005 01:57 AM
Re: Qpopper and shadow password : password incorrect
Users accounts are not locked.
Anyway my system is not trusted. I only install ShadowPassword product downloaded from hp Software depot. (usr/lbin/modprpw reply me System is not trusted.) I just want hide crypted password originaly in /etc/passwd to any users.
thanks
- Mark as New
- Bookmark
- Subscribe
- Mute
- Subscribe to RSS Feed
- Permalink
- Report Inappropriate Content
тАО06-06-2005 02:36 AM
тАО06-06-2005 02:36 AM
Re: Qpopper and shadow password : password incorrect
Sometimes in these circumstances it helps to reset the password on the user or to use sam to reactivate.
I've run qpopper trusted and shadow and it is quite possible to run this combination.
SEP
Owner of ISN Corporation
http://isnamerica.com
http://hpuxconsulting.com
Sponsor: http://hpux.ws
Twitter: http://twitter.com/hpuxlinux
Founder http://newdatacloud.com
- Mark as New
- Bookmark
- Subscribe
- Mute
- Subscribe to RSS Feed
- Permalink
- Report Inappropriate Content
тАО06-06-2005 03:34 AM
тАО06-06-2005 03:34 AM
Re: Qpopper and shadow password : password incorrect
the user (its me) is active
I reset the password by the command passwd
and test qpopper like that :
# telnet d pop3
Trying...
Connected to d.gvr.hp.
Escape character is '^]'.
+OK Qpopper (version 4.0.8) at D.gvr.hp starting.
user joel
+OK Password required for joel.
pass
-ERR [AUTH] Password supplied for "joel" is incorrect.
+OK Pop server at D.gvr.hp signing off.
Connection closed by foreign host.
/root#
the password is correct, but dont work...
- Mark as New
- Bookmark
- Subscribe
- Mute
- Subscribe to RSS Feed
- Permalink
- Report Inappropriate Content
тАО06-06-2005 04:25 AM
тАО06-06-2005 04:25 AM
SolutionFirst, compile qpopper and add the '--with-pam=pop3' option to your configure.
# ./configure --enable-specialauth --with-pam=pop3
Now once that is done, modify the /etc/pam.conf file and add the line 'pop3 auth required /usr/lib/security/libpam_unix.1' to all 4 sections of the pam.conf file (authentication management, account management, session management, and password management)
When you are done your /etc/pam.conf should look similar to this:
# cat /etc/pam.conf
#
# PAM configuration
#
# Authentication management
#
login auth required /usr/lib/security/libpam_unix.1
su auth required /usr/lib/security/libpam_unix.1
ftp auth required /usr/lib/security/libpam_unix.1
pop3 auth required /usr/lib/security/libpam_unix.1
OTHER auth required /usr/lib/security/libpam_unix.1
#
# Account management
#
login account required /usr/lib/security/libpam_unix.1
su account required /usr/lib/security/libpam_unix.1
ftp account required /usr/lib/security/libpam_unix.1
pop3 auth required /usr/lib/security/libpam_unix.1
#
OTHER account required /usr/lib/security/libpam_unix.1
# Session management
#
login session required /usr/lib/security/libpam_unix.1
pop3 auth required /usr/lib/security/libpam_unix.1
OTHER session required /usr/lib/security/libpam_unix.1
#
# Password management
#
login password required /usr/lib/security/libpam_unix.1
passwd password required /usr/lib/security/libpam_unix.1
pop3 auth required /usr/lib/security/libpam_unix.1
OTHER password required /usr/lib/security/libpam_unix.1
Now try logging in again. It should work.
- Mark as New
- Bookmark
- Subscribe
- Mute
- Subscribe to RSS Feed
- Permalink
- Report Inappropriate Content
тАО06-06-2005 05:22 AM
тАО06-06-2005 05:22 AM
Re: Qpopper and shadow password : password incorrect
- Mark as New
- Bookmark
- Subscribe
- Mute
- Subscribe to RSS Feed
- Permalink
- Report Inappropriate Content
тАО06-06-2005 05:25 AM
тАО06-06-2005 05:25 AM