- Community Home
- >
- Servers and Operating Systems
- >
- Operating Systems
- >
- Operating System - HP-UX
- >
- 1000BASE-ST ETHERNET will not connect after a re-b...
Categories
Company
Local Language
Forums
Discussions
Forums
- Data Protection and Retention
- Entry Storage Systems
- Legacy
- Midrange and Enterprise Storage
- Storage Networking
- HPE Nimble Storage
Discussions
Discussions
Discussions
Forums
Forums
Discussions
Discussion Boards
Discussion Boards
Discussion Boards
Discussion Boards
- BladeSystem Infrastructure and Application Solutions
- Appliance Servers
- Alpha Servers
- BackOffice Products
- Internet Products
- HPE 9000 and HPE e3000 Servers
- Networking
- Netservers
- Secure OS Software for Linux
- Server Management (Insight Manager 7)
- Windows Server 2003
- Operating System - Tru64 Unix
- ProLiant Deployment and Provisioning
- Linux-Based Community / Regional
- Microsoft System Center Integration
Discussion Boards
Discussion Boards
Discussion Boards
Discussion Boards
Discussion Boards
Discussion Boards
Discussion Boards
Discussion Boards
Discussion Boards
Discussion Boards
Discussion Boards
Discussion Boards
Discussion Boards
Discussion Boards
Discussion Boards
Discussion Boards
Discussion Boards
Discussion Boards
Discussion Boards
Discussion Boards
Discussion Boards
Discussion Boards
Community
Resources
Forums
Blogs
- Subscribe to RSS Feed
- Mark Topic as New
- Mark Topic as Read
- Float this Topic for Current User
- Bookmark
- Subscribe
- Printer Friendly Page
- Mark as New
- Bookmark
- Subscribe
- Mute
- Subscribe to RSS Feed
- Permalink
- Report Inappropriate Content
тАО05-05-2011 11:02 AM
тАО05-05-2011 11:02 AM
I have a new rp4440 with a 1000NASE-ST (copper)
for lan interface. good OS running good but every time i re-boot the system, the boot completes but the lan0 will not connect. The only way to get the network to talk is to unplug the copper from the card and plug it back in at which time the network responds.
until that happens i cannot ping the local gate way.
nslookup is good. netsonf is good as is all other configs i can think of.
any help on this ?
jim
Solved! Go to Solution.
- Mark as New
- Bookmark
- Subscribe
- Mute
- Subscribe to RSS Feed
- Permalink
- Report Inappropriate Content
тАО05-05-2011 11:21 AM
тАО05-05-2011 11:21 AM
SolutionINTERFACE_NAME[0]="lan2"
IP_ADDRESS[0]="192.72.16.20"
SUBNET_MASK[0]="255.255.0.0"
BROADCAST_ADDRESS[0]=""
INTERFACE_STATE[0]=""
DHCP_ENABLE[0]=0
????
- Mark as New
- Bookmark
- Subscribe
- Mute
- Subscribe to RSS Feed
- Permalink
- Report Inappropriate Content
тАО05-05-2011 11:26 AM
тАО05-05-2011 11:26 AM
Re: 1000BASE-ST ETHERNET will not connect after a re-boot
thanks
- Mark as New
- Bookmark
- Subscribe
- Mute
- Subscribe to RSS Feed
- Permalink
- Report Inappropriate Content
тАО05-06-2011 01:35 AM
тАО05-06-2011 01:35 AM
Re: 1000BASE-ST ETHERNET will not connect after a re-boot
...
INTERFACE_NAME[0]=lan0
IP_ADDRESS[0]=172.16.3.70
SUBNET_MASK[0]=255.255.255.0
BROADCAST_ADDRESS[0]=172.16.3.255
INTERFACE_STATE[0]=up
DHCP_ENABLE[0]=0
INTERFACE_MODULES[0]=""
...
...
...
INTERFACE_NAME[1]=lan1
IP_ADDRESS[1]=172.16.3.70
SUBNET_MASK[1]=255.255.255.0
BROADCAST_ADDRESS[1]=172.16.3.255
INTERFACE_STATE[1]=down
DHCP_ENABLE[1]=0
Unix operates with beer.
- Mark as New
- Bookmark
- Subscribe
- Mute
- Subscribe to RSS Feed
- Permalink
- Report Inappropriate Content
тАО05-06-2011 04:45 AM
тАО05-06-2011 04:45 AM
Re: 1000BASE-ST ETHERNET will not connect after a re-boot
- Mark as New
- Bookmark
- Subscribe
- Mute
- Subscribe to RSS Feed
- Permalink
- Report Inappropriate Content
тАО05-06-2011 06:35 AM
тАО05-06-2011 06:35 AM
Re: 1000BASE-ST ETHERNET will not connect after a re-boot
and lan1 assigned an the same ip. However the lan1 was not enabled. I saw this but i was counting on the fact that if an interface is not enabled it is also not configured. In any case, i commented out lan1 and that did the fix
thanks
jim