- Community Home
- >
- Servers and Operating Systems
- >
- Legacy
- >
- Networking
- >
- ARCserve and Network card?
Networking
1753834
Members
7905
Online
108806
Solutions
Forums
Categories
Company
Local Language
back
Forums
Discussions
Forums
- Data Protection and Retention
- Entry Storage Systems
- Legacy
- Midrange and Enterprise Storage
- Storage Networking
- HPE Nimble Storage
Discussions
Discussions
Discussions
Forums
Discussions
back
Discussion Boards
Discussion Boards
Discussion Boards
Discussion Boards
- BladeSystem Infrastructure and Application Solutions
- Appliance Servers
- Alpha Servers
- BackOffice Products
- Internet Products
- HPE 9000 and HPE e3000 Servers
- Networking
- Netservers
- Secure OS Software for Linux
- Server Management (Insight Manager 7)
- Windows Server 2003
- Operating System - Tru64 Unix
- ProLiant Deployment and Provisioning
- Linux-Based Community / Regional
- Microsoft System Center Integration
Discussion Boards
Discussion Boards
Discussion Boards
Discussion Boards
Discussion Boards
Discussion Boards
Discussion Boards
Discussion Boards
Discussion Boards
Discussion Boards
Discussion Boards
Discussion Boards
Discussion Boards
Discussion Boards
Discussion Boards
Discussion Boards
Discussion Boards
Discussion Boards
Discussion Boards
Blogs
Information
Community
Resources
Community Language
Language
Forums
Blogs
Topic Options
- Subscribe to RSS Feed
- Mark Topic as New
- Mark Topic as Read
- Float this Topic for Current User
- Bookmark
- Subscribe
- Printer Friendly Page
- Mark as New
- Bookmark
- Subscribe
- Mute
- Subscribe to RSS Feed
- Permalink
- Report Inappropriate Content
10-11-2002 05:25 AM
10-11-2002 05:25 AM
ARCserve and Network card?
Backup ran fine before I upgraded OS from HP 10.20 to 11.0 with Oracle database 7.3.4.4.
After the cold-installed of OS 11, ARCserve runs very slow, and the database is about 4G in size, but it never completed the backup. It took 6hr 52 min to backup 410.95 MB.
What's happening after the new OS cold-install
that have impact on ARCserve backup?
Thanks in advance.
I am new to ARCserve backup and UNIX Admin.
After the cold-installed of OS 11, ARCserve runs very slow, and the database is about 4G in size, but it never completed the backup. It took 6hr 52 min to backup 410.95 MB.
What's happening after the new OS cold-install
that have impact on ARCserve backup?
Thanks in advance.
I am new to ARCserve backup and UNIX Admin.
1 REPLY 1
- Mark as New
- Bookmark
- Subscribe
- Mute
- Subscribe to RSS Feed
- Permalink
- Report Inappropriate Content
10-11-2002 09:40 AM
10-11-2002 09:40 AM
Re: ARCserve and Network card?
Check the documentation that came with the software.
Make sure that it is fully compatibile with 11.00, and that all kernel tuning parameters have been applied.
I couldn't find any mention of required or updated patches.
For some of the NON UNIX OS's there were lots of mentions of moving to a newer version.
Are you backing up the Server directly, or across the network by using the ARCserve client?
BTW: You may get a better responce by posting this question across in the HP-UX forum.
Jon
Make sure that it is fully compatibile with 11.00, and that all kernel tuning parameters have been applied.
I couldn't find any mention of required or updated patches.
For some of the NON UNIX OS's there were lots of mentions of moving to a newer version.
Are you backing up the Server directly, or across the network by using the ARCserve client?
BTW: You may get a better responce by posting this question across in the HP-UX forum.
Jon
"Do or do not. There is no try!" - Yoda
The opinions expressed above are the personal opinions of the authors, not of Hewlett Packard Enterprise. By using this site, you accept the Terms of Use and Rules of Participation.
News and Events
Support
© Copyright 2024 Hewlett Packard Enterprise Development LP