Simpler Navigation for Servers and Operating Systems - Please Update Your Bookmarks
Completed: a much simpler Servers and Operating Systems section of the Community. We combined many of the older boards, so you won't have to click through so many levels to get at the information you need. Check the consolidated boards here as many sub-forums are now single boards.
If you have bookmarked forums or discussion boards in Servers and Operating Systems, we suggest you check and update them as needed.
Networking
cancel
Showing results for 
Search instead for 
Did you mean: 

How to setup NIC Failover in HP-UX 11.31 with HP APA

MikeL_4
Super Advisor

How to setup NIC Failover in HP-UX 11.31 with HP APA

I am new to H-UX 11.31, and I am trying to setup some new servers, and am looking for help in setting up NIC failover on the servers with HP APA...

 

I am using LAN2 as my Primary NIC, and LAN3 is to be my failover NIC...

 

Can anyone reference with where I need to start to configure this on the servers....

 

=>lanscan
Hardware Station        Crd Hdw   Net-Interface  NM  MAC       HP-DLPI DLPI
Path     Address        In# State NamePPA        ID  Type      Support Mjr#
0/0/0/3/0/0/0 0x3C4A9248215C 0   UP    lan0 snap0     1   ETHER     Yes     119
0/0/0/3/0/0/1 0x3C4A92482160 1   UP    lan1 snap1     2   ETHER     Yes     119
0/0/0/4/0/0/0 0x3C4A92482164 2   UP    lan2 snap2     3   ETHER     Yes     119
VLAN5000 0x3C4A92482164 5000 UP    lan5000 snap5000 56  ETHER     Yes     119
0/0/0/4/0/0/1 0x3C4A92482168 3   UP    lan3 snap3     4   ETHER     Yes     119
LinkAgg0 0x000000000000 900 DOWN  lan900 snap900 6   ETHER     Yes     119
LinkAgg1 0x000000000000 901 DOWN  lan901 snap901 7   ETHER     Yes     119
LinkAgg2 0x000000000000 902 DOWN  lan902 snap902 8   ETHER     Yes     119
LinkAgg3 0x000000000000 903 DOWN  lan903 snap903 9   ETHER     Yes     119
LinkAgg4 0x000000000000 904 DOWN  lan904 snap904 10  ETHER     Yes     119
=>ifconfig lan2
lan2: flags=2000000000001843<UP,BROADCAST,RUNNING,MULTICAST,CKO,TSO>
        inet 10.195.32.13 netmask ffffffe0 broadcast 10.195.32.31
=>ifconfig lan5000
lan5000: flags=6000000000001843<UP,BROADCAST,RUNNING,MULTICAST,CKO,TSO,VLAN>
        inet 155.90.120.13 netmask ffffffe0 broadcast 155.90.120.31
=>ifconfig lan3
ifconfig: no such interface
=>

3 REPLIES
Steven E. Protter
Exalted Contributor

Re: How to setup NIC Failover in HP-UX 11.31 with HP APA

Shalom,

 

I would start here <link click me>

 

SEP

 

Steven E Protter
Owner of ISN Corporation
http://isnamerica.com
http://hpuxconsulting.com
Sponsor: http://hpux.ws
Twitter: http://twitter.com/hpuxlinux
Founder http://newdatacloud.com
MikeL_4
Super Advisor

Re: How to setup NIC Failover in HP-UX 11.31 with HP APA

=>lanadmin -X -p 2 LAN_MONITOR 900

Port 2 set to LAN_MONITOR

=>lanadmin -X -p 3 LAN_MONITOR 900

Port 3 set to LAN_MONITOR

=>lanadmin -x -p 2 900

 

**** PORT NUMBER: 2 *******

Port Mode               : LAN_MONITOR

PortState                : PROTOCOL OFF

Port Group Capability     : 5

Port Priority             : 0

=>lanadmin -x -p 3 900

 

**** PORT NUMBER: 3 *******

Port Mode               : LAN_MONITOR

PortState                : PROTOCOL OFF

Port Group Capability     : 5

Port Priority             : 0

=>

 

=>lanqueryconf -s

WARNING: Port 2 has VLAN(s) configured. It is not usable in a

         failover-group.

WARNING: None of the ports in subnet (  3 ) have an IP address assigned

No Fail-Over Groups found. ASCII file not created

=>

Naj
Valued Contributor

Re: How to setup NIC Failover in HP-UX 11.31 with HP APA

HI

 

You may read this as reference

 

http://www.hpuxtips.es/?q=node/74

 

Thanks

 

BR

Naj


____________________________________________
:: Really appreciate if you could assign some points.
:: Don't know how to assign point? Click the KUDOS! star!