- Community Home
- >
- Servers and Operating Systems
- >
- Operating Systems
- >
- Operating System - OpenVMS
- >
- CMDSCRIPT and VTDPY
Categories
Company
Local Language
Forums
Discussions
Forums
- Data Protection and Retention
- Entry Storage Systems
- Legacy
- Midrange and Enterprise Storage
- Storage Networking
- HPE Nimble Storage
Discussions
Discussions
Discussions
Forums
Forums
Discussions
Discussion Boards
Discussion Boards
Discussion Boards
Discussion Boards
- BladeSystem Infrastructure and Application Solutions
- Appliance Servers
- Alpha Servers
- BackOffice Products
- Internet Products
- HPE 9000 and HPE e3000 Servers
- Networking
- Netservers
- Secure OS Software for Linux
- Server Management (Insight Manager 7)
- Windows Server 2003
- Operating System - Tru64 Unix
- ProLiant Deployment and Provisioning
- Linux-Based Community / Regional
- Microsoft System Center Integration
Discussion Boards
Discussion Boards
Discussion Boards
Discussion Boards
Discussion Boards
Discussion Boards
Discussion Boards
Discussion Boards
Discussion Boards
Discussion Boards
Discussion Boards
Discussion Boards
Discussion Boards
Discussion Boards
Discussion Boards
Discussion Boards
Discussion Boards
Discussion Boards
Discussion Boards
Discussion Boards
Discussion Boards
Discussion Boards
Community
Resources
Forums
Blogs
- Subscribe to RSS Feed
- Mark Topic as New
- Mark Topic as Read
- Float this Topic for Current User
- Bookmark
- Subscribe
- Printer Friendly Page
- Mark as New
- Bookmark
- Subscribe
- Mute
- Subscribe to RSS Feed
- Permalink
- Report Inappropriate Content
тАО05-01-2008 07:17 AM
тАО05-01-2008 07:17 AM
CMDSCRIPT and VTDPY
Is there a way to either 1) send Control-C through to VTDPY or 2) somehow exit VTDPY so I can run it using hyperterm and the wired command line interface?
I am stuck!
Thanks.
- Mark as New
- Bookmark
- Subscribe
- Mute
- Subscribe to RSS Feed
- Permalink
- Report Inappropriate Content
тАО05-01-2008 07:30 AM
тАО05-01-2008 07:30 AM
Re: CMDSCRIPT and VTDPY
$ SET NOCONTROL=Y
- Mark as New
- Bookmark
- Subscribe
- Mute
- Subscribe to RSS Feed
- Permalink
- Report Inappropriate Content
тАО05-01-2008 07:49 AM
тАО05-01-2008 07:49 AM
Re: CMDSCRIPT and VTDPY
No, CMDSCRIPT is a utility to control HSG raid controllers (I have an HSG80 running version V86F-8 ... which I am trying to upgrade to -13) from the DCL prompt instead of connecting to the management port of the HSG raid controller via a serial cable and hyperterminal.
You would use a command like :
$ CMDSCRIPT :== $CMDSCRIPT
$ CMDSCRIPT -f "$1$GGA99"
which gets you to the HSG80 prompt where I ran VTDPY.
HSGOCC3> RUN VTDPY
When I hit CONTROL-C, I get ...
*INTERRUPT*
$
I did try the $ SET NOCONTROL=Y before using the CMDSCRIPT -f "$1$GGA99" and I still get the *INTERRUPT*, however it does not kick me back to the DCL prompt.
It was worth a try! :)
- Mark as New
- Bookmark
- Subscribe
- Mute
- Subscribe to RSS Feed
- Permalink
- Report Inappropriate Content
тАО05-01-2008 07:51 AM
тАО05-01-2008 07:51 AM
Re: CMDSCRIPT and VTDPY
- Mark as New
- Bookmark
- Subscribe
- Mute
- Subscribe to RSS Feed
- Permalink
- Report Inappropriate Content
тАО05-01-2008 12:28 PM
тАО05-01-2008 12:28 PM
Re: CMDSCRIPT and VTDPY
Thanks for the response.
The data I need is the HSG80 controller % idle. The patch procedure states that I can restart the HSG80 without shutting down the OpenVms system if the idle time is greater that 50%.
The system does not run SNMP, so if it is possible to get the data that way, it will not be an easy process to get setup. I assume there is some setup required to get SNMP to report back HSG80 statistics. A lot of setup issues there I do not know how to do :(
It is really too bad there does not seem to be a way to kill off the CMDSCRIPT session on the HSG80 from the hyperterminal/serial cable session. I could get the data I need by running VTDPY via hyperterminal and the serial cable, but with VTDPY already running via CMDSCRIPT it will not allow me to run any other program.
I also tried to create a file that has a CONTROL-C ascii character (03) in it, and copying that to the FTA terminal device that is running CMDSCRIPT/VTDPY but that did not work. :(
My main problem now is trying to kill off the CMDSCRIPT session on the HSG80 that is currently running the VTDPY program.
Thanks.
- Mark as New
- Bookmark
- Subscribe
- Mute
- Subscribe to RSS Feed
- Permalink
- Report Inappropriate Content
тАО05-02-2008 02:45 PM
тАО05-02-2008 02:45 PM
Re: CMDSCRIPT and VTDPY
http://h71000.www7.hp.com/doc/732FINAL/aa-pv6sf-tk/aa-pv6sf-tk.HTMl
- Mark as New
- Bookmark
- Subscribe
- Mute
- Subscribe to RSS Feed
- Permalink
- Report Inappropriate Content
тАО08-04-2008 11:33 AM
тАО08-04-2008 11:33 AM