- Community Home
- >
- Servers and Operating Systems
- >
- Operating Systems
- >
- Operating System - OpenVMS
- >
- Re: DCPS support of new HP printer
Categories
Company
Local Language
Forums
Discussions
Forums
- Data Protection and Retention
- Entry Storage Systems
- Legacy
- Midrange and Enterprise Storage
- Storage Networking
- HPE Nimble Storage
Discussions
Discussions
Discussions
Forums
Discussions
Discussion Boards
Discussion Boards
Discussion Boards
Discussion Boards
- BladeSystem Infrastructure and Application Solutions
- Appliance Servers
- Alpha Servers
- BackOffice Products
- Internet Products
- HPE 9000 and HPE e3000 Servers
- Networking
- Netservers
- Secure OS Software for Linux
- Server Management (Insight Manager 7)
- Windows Server 2003
- Operating System - Tru64 Unix
- ProLiant Deployment and Provisioning
- Linux-Based Community / Regional
- Microsoft System Center Integration
Discussion Boards
Discussion Boards
Discussion Boards
Discussion Boards
Discussion Boards
Discussion Boards
Discussion Boards
Discussion Boards
Discussion Boards
Discussion Boards
Discussion Boards
Discussion Boards
Discussion Boards
Discussion Boards
Discussion Boards
Discussion Boards
Discussion Boards
Discussion Boards
Discussion Boards
Community
Resources
Forums
Blogs
- Subscribe to RSS Feed
- Mark Topic as New
- Mark Topic as Read
- Float this Topic for Current User
- Bookmark
- Subscribe
- Printer Friendly Page
- Mark as New
- Bookmark
- Subscribe
- Mute
- Subscribe to RSS Feed
- Permalink
- Report Inappropriate Content
07-31-2013 03:21 AM
07-31-2013 03:21 AM
DCPS support of new HP printer
We have a new replacement printer which prints ok but we have lost the ability to select a specific tray on the new printer. Our old printer was an HP LaserJet 9050dn, and our new one is an HP LaserJet 600 M602. We have OpenVMS I64 V8.3-1H1 with DCPS V2.6. There is a previous post for this same issue (different printer http://h30499.www3.hp.com/t5/System-Management/DCPS-support-of-new-printers/m-p/5146225#M38432) and the solution is to create a new module, but the question is, which of the existing modules is best to use as the basis for the 'HPGENERIC' module for the new printer. Any help will be gratefully received.
- Mark as New
- Bookmark
- Subscribe
- Mute
- Subscribe to RSS Feed
- Permalink
- Report Inappropriate Content
01-20-2015 03:45 AM
01-20-2015 03:45 AM
Re: DCPS support of new HP printer
We face the same problem. I tried HPCLJ9500, HPLJ9050MFP and HPLJ9055 with no success. Is nobody out there who could shed a light on this?
Thanks
Axel
- Mark as New
- Bookmark
- Subscribe
- Mute
- Subscribe to RSS Feed
- Permalink
- Report Inappropriate Content
01-20-2015 08:03 AM
01-20-2015 08:03 AM
Re: DCPS support of new HP printer
I am not familiar with these particular models, but in the past, I have found that the "default" settings for the newer printers can be altered such that they can mimic the "older" ones. In one case, we had to change the default to PCL5 support. If you don't require any of the newer features (PCL6 has more than PCL5 for example) setting the printer to the older type settings may resolve your problem.
Dan
- Mark as New
- Bookmark
- Subscribe
- Mute
- Subscribe to RSS Feed
- Permalink
- Report Inappropriate Content
01-21-2015 11:49 PM
01-21-2015 11:49 PM
Re: DCPS support of new HP printer
Solution found: The modules from HPLJ9050MFP do the job if both INITPSDEVICE and SETOUTPUTTRAY are used to replace the HPGENERIC variants. The SETOUTPUTTRAY module has to be modified slightly in lines 6 to 9: bin_1 must map to OUTPUT BIN 1 (not to 2), bin_2 to OUTPUT BIN 2 and so on.
Axel