- Community Home
- >
- Servers and Operating Systems
- >
- Operating Systems
- >
- Operating System - OpenVMS
- >
- Re: HSG80, CMDSCRIPT and a hanging GS160...
Operating System - OpenVMS
1752766
Members
5094
Online
108789
Solutions
Forums
Categories
Company
Local Language
юдл
back
Forums
Discussions
Forums
- Data Protection and Retention
- Entry Storage Systems
- Legacy
- Midrange and Enterprise Storage
- Storage Networking
- HPE Nimble Storage
Discussions
Discussions
Discussions
Forums
Forums
Discussions
юдл
back
Discussion Boards
Discussion Boards
Discussion Boards
Discussion Boards
- BladeSystem Infrastructure and Application Solutions
- Appliance Servers
- Alpha Servers
- BackOffice Products
- Internet Products
- HPE 9000 and HPE e3000 Servers
- Networking
- Netservers
- Secure OS Software for Linux
- Server Management (Insight Manager 7)
- Windows Server 2003
- Operating System - Tru64 Unix
- ProLiant Deployment and Provisioning
- Linux-Based Community / Regional
- Microsoft System Center Integration
Discussion Boards
Discussion Boards
Discussion Boards
Discussion Boards
Discussion Boards
Discussion Boards
Discussion Boards
Discussion Boards
Discussion Boards
Discussion Boards
Discussion Boards
Discussion Boards
Discussion Boards
Discussion Boards
Discussion Boards
Discussion Boards
Discussion Boards
Discussion Boards
Discussion Boards
Discussion Boards
Discussion Boards
Discussion Boards
Blogs
Information
Community
Resources
Community Language
Language
Forums
Blogs
Go to solution
Topic Options
- Subscribe to RSS Feed
- Mark Topic as New
- Mark Topic as Read
- Float this Topic for Current User
- Bookmark
- Subscribe
- Printer Friendly Page
- Mark as New
- Bookmark
- Subscribe
- Mute
- Subscribe to RSS Feed
- Permalink
- Report Inappropriate Content
тАО01-06-2004 01:31 AM
тАО01-06-2004 01:31 AM
Hi all.
We have experienced a hanging GS160 when adding
a device using CMDSCRIPT on an HSG80 controller.
Here are some details:
The GS160 is running OpenVMS v7.3-2
The HSG80s are running the latest firmware rev
87P-4.
The node in question is running a command
which adds a unit at the controller running
SYS$SYSTEM:CMDSCRIPT.
Passed to CMDSCRIPT is a series of commands
with several delays before invoking a single command. Example:
add snap d95 disk10400 d14
delay 15
set d95 dis=all
delay 5
set d95 enable=phobos2a1,phobos1b1
delay 5
set d95 identifier=95
Last night, at the 'Add' command the GS160 hung requiring a reboot of the node. This does not happen often but every now and then.
Is this a timing issue? HSG saturation?
(No hardware errors are detected on the device
being added nor on the controller itself)
Any ideas?
Thanks in advance.
Regards,
Richard Brock
We have experienced a hanging GS160 when adding
a device using CMDSCRIPT on an HSG80 controller.
Here are some details:
The GS160 is running OpenVMS v7.3-2
The HSG80s are running the latest firmware rev
87P-4.
The node in question is running a command
which adds a unit at the controller running
SYS$SYSTEM:CMDSCRIPT.
Passed to CMDSCRIPT is a series of commands
with several delays before invoking a single command. Example:
add snap d95 disk10400 d14
delay 15
set d95 dis=all
delay 5
set d95 enable=phobos2a1,phobos1b1
delay 5
set d95 identifier=95
Last night, at the 'Add' command the GS160 hung requiring a reboot of the node. This does not happen often but every now and then.
Is this a timing issue? HSG saturation?
(No hardware errors are detected on the device
being added nor on the controller itself)
Any ideas?
Thanks in advance.
Regards,
Richard Brock
Solved! Go to Solution.
3 REPLIES 3
- Mark as New
- Bookmark
- Subscribe
- Mute
- Subscribe to RSS Feed
- Permalink
- Report Inappropriate Content
тАО01-06-2004 02:38 AM
тАО01-06-2004 02:38 AM
Re: HSG80, CMDSCRIPT and a hanging GS160...
as you reboot, you should take a crash, and then you will have plenty of time to analyze and see why it was hanging.
regards
Gerard
regards
Gerard
- Mark as New
- Bookmark
- Subscribe
- Mute
- Subscribe to RSS Feed
- Permalink
- Report Inappropriate Content
тАО01-06-2004 07:35 AM
тАО01-06-2004 07:35 AM
Re: HSG80, CMDSCRIPT and a hanging GS160...
On a GS 160, you should install Amds or Availability manager anyway. And may be it will help. it is available at
http://h71000.www7.hp.com/openvms/products/availman/index.html
http://h71000.www7.hp.com/openvms/products/availman/index.html
- Mark as New
- Bookmark
- Subscribe
- Mute
- Subscribe to RSS Feed
- Permalink
- Report Inappropriate Content
тАО01-06-2004 09:45 AM
тАО01-06-2004 09:45 AM
Solution
How is your CMDSCRIPT connecting to the CLI of the HSG? Are you using HSZTERM$SCSIPAD.EXE? If so, do you also have a SAN appliance that is monitoring the same HSG? If so, both are attempting to use the same I/O channel into the HSG80 controller. while this would stomp on the others monitoring, it should not have hung your system.
According to the CLI manual, you do not need the SET D95 DIS=all This is the default when creating a snapshot unit.
According to the CLI manual, you do not need the SET D95 DIS=all This is the default when creating a snapshot unit.
VMS SAN mechanic
The opinions expressed above are the personal opinions of the authors, not of Hewlett Packard Enterprise. By using this site, you accept the Terms of Use and Rules of Participation.
News and Events
Support
© Copyright 2024 Hewlett Packard Enterprise Development LP