- Community Home
- >
- Servers and Operating Systems
- >
- Operating Systems
- >
- Operating System - OpenVMS
- >
- Monitor cluster problem!
Categories
Company
Local Language
Forums
Discussions
Forums
- Data Protection and Retention
- Entry Storage Systems
- Legacy
- Midrange and Enterprise Storage
- Storage Networking
- HPE Nimble Storage
Discussions
Discussions
Discussions
Forums
Forums
Discussions
Discussion Boards
Discussion Boards
Discussion Boards
Discussion Boards
- BladeSystem Infrastructure and Application Solutions
- Appliance Servers
- Alpha Servers
- BackOffice Products
- Internet Products
- HPE 9000 and HPE e3000 Servers
- Networking
- Netservers
- Secure OS Software for Linux
- Server Management (Insight Manager 7)
- Windows Server 2003
- Operating System - Tru64 Unix
- ProLiant Deployment and Provisioning
- Linux-Based Community / Regional
- Microsoft System Center Integration
Discussion Boards
Discussion Boards
Discussion Boards
Discussion Boards
Discussion Boards
Discussion Boards
Discussion Boards
Discussion Boards
Discussion Boards
Discussion Boards
Discussion Boards
Discussion Boards
Discussion Boards
Discussion Boards
Discussion Boards
Discussion Boards
Discussion Boards
Discussion Boards
Discussion Boards
Discussion Boards
Discussion Boards
Discussion Boards
Community
Resources
Forums
Blogs
- Subscribe to RSS Feed
- Mark Topic as New
- Mark Topic as Read
- Float this Topic for Current User
- Bookmark
- Subscribe
- Printer Friendly Page
- Mark as New
- Bookmark
- Subscribe
- Mute
- Subscribe to RSS Feed
- Permalink
- Report Inappropriate Content
тАО07-16-2006 07:37 PM
тАО07-16-2006 07:37 PM
I'm running OpenVMS V8.2 on my cluster servers. When using MONITOR CLUSTER command I get response from all servers but one. I found out that VPM$SERVER is not running on it and it is also not present in user database (UAF). I'm using DECnet Phase IV and. I'm using LAN interconnet.
Where I did make a mistake? Why VPM$SERVER is not present?
Best regards
Domen Setar
Solved! Go to Solution.
- Mark as New
- Bookmark
- Subscribe
- Mute
- Subscribe to RSS Feed
- Permalink
- Report Inappropriate Content
тАО07-16-2006 07:44 PM
тАО07-16-2006 07:44 PM
Re: Monitor cluster problem!
the VPM$SERVER account should have been created by @NETCONFIG when configuring the DECnet Phase IV object database.
...
Do you want a default account for the VPM object? [YES]:
...
You do not need to have the VPM_SERVER process running, if you're using DECnet in your cluster. It's only required, if the nodes are running TCPIP only.
Volker.
- Mark as New
- Bookmark
- Subscribe
- Mute
- Subscribe to RSS Feed
- Permalink
- Report Inappropriate Content
тАО07-16-2006 07:57 PM
тАО07-16-2006 07:57 PM
Re: Monitor cluster problem!
I tried this many times, but I never did get a question about VPM. I don't know why.
Domen
- Mark as New
- Bookmark
- Subscribe
- Mute
- Subscribe to RSS Feed
- Permalink
- Report Inappropriate Content
тАО07-16-2006 08:11 PM
тАО07-16-2006 08:11 PM
Re: Monitor cluster problem!
do you have a MIRRO$SERVER account ? That one is being created in the SAME way as the VPM$SERVER account (actually immediately preceeding it). Have a look at NETCONFIG.COM or run it with SET VERIFY.
Volker.
- Mark as New
- Bookmark
- Subscribe
- Mute
- Subscribe to RSS Feed
- Permalink
- Report Inappropriate Content
тАО07-16-2006 08:58 PM
тАО07-16-2006 08:58 PM
Re: Monitor cluster problem!
I didn't have mirro$server accunt. I tried with netconfig again and have solved the VPM$SERVER mistery. The problem was that I used the option to create defalut DECNET account, which causes procedure to skip creation of VPM$SERVER and MIRRO$SERVER accounts.
Now I have both accounts. But still I get a message "Unable to connect to remote node" when I use MONITOR CLUSTER command. Any idea what I need to do now?
Domen
- Mark as New
- Bookmark
- Subscribe
- Mute
- Subscribe to RSS Feed
- Permalink
- Report Inappropriate Content
тАО07-16-2006 09:11 PM
- Mark as New
- Bookmark
- Subscribe
- Mute
- Subscribe to RSS Feed
- Permalink
- Report Inappropriate Content
тАО07-16-2006 09:44 PM
тАО07-16-2006 09:44 PM
Re: Monitor cluster problem!
By some mistake DECNET was not running on the server. Everything works fine now.
Thank you for helping me.
Domen
- Mark as New
- Bookmark
- Subscribe
- Mute
- Subscribe to RSS Feed
- Permalink
- Report Inappropriate Content
тАО07-16-2006 09:46 PM
тАО07-16-2006 09:46 PM