- Community Home
- >
- Servers and Operating Systems
- >
- Operating Systems
- >
- Operating System - OpenVMS
- >
- Re: Network card info required
Categories
Company
Local Language
Forums
Discussions
Forums
- Data Protection and Retention
- Entry Storage Systems
- Legacy
- Midrange and Enterprise Storage
- Storage Networking
- HPE Nimble Storage
Discussions
Discussions
Discussions
Forums
Forums
Discussions
Discussion Boards
Discussion Boards
Discussion Boards
Discussion Boards
- BladeSystem Infrastructure and Application Solutions
- Appliance Servers
- Alpha Servers
- BackOffice Products
- Internet Products
- HPE 9000 and HPE e3000 Servers
- Networking
- Netservers
- Secure OS Software for Linux
- Server Management (Insight Manager 7)
- Windows Server 2003
- Operating System - Tru64 Unix
- ProLiant Deployment and Provisioning
- Linux-Based Community / Regional
- Microsoft System Center Integration
Discussion Boards
Discussion Boards
Discussion Boards
Discussion Boards
Discussion Boards
Discussion Boards
Discussion Boards
Discussion Boards
Discussion Boards
Discussion Boards
Discussion Boards
Discussion Boards
Discussion Boards
Discussion Boards
Discussion Boards
Discussion Boards
Discussion Boards
Discussion Boards
Discussion Boards
Discussion Boards
Discussion Boards
Discussion Boards
Community
Resources
Forums
Blogs
- Subscribe to RSS Feed
- Mark Topic as New
- Mark Topic as Read
- Float this Topic for Current User
- Bookmark
- Subscribe
- Printer Friendly Page
- Mark as New
- Bookmark
- Subscribe
- Mute
- Subscribe to RSS Feed
- Permalink
- Report Inappropriate Content
тАО12-06-2006 03:38 AM
тАО12-06-2006 03:38 AM
Solved! Go to Solution.
- Mark as New
- Bookmark
- Subscribe
- Mute
- Subscribe to RSS Feed
- Permalink
- Report Inappropriate Content
тАО12-06-2006 03:43 AM
- Mark as New
- Bookmark
- Subscribe
- Mute
- Subscribe to RSS Feed
- Permalink
- Report Inappropriate Content
тАО12-06-2006 03:44 AM
тАО12-06-2006 03:44 AM
Re: Network card info required
$ ANAL/SYS
SDA> CLUE CONFIG
SDA> SHOW LAN/FULL/DEV=Exx ! VMS device name
SDA> EXIT
$ MC LANCP SHOW DEV/INT Exx
should show more information about the network interface card.
Volker.
- Mark as New
- Bookmark
- Subscribe
- Mute
- Subscribe to RSS Feed
- Permalink
- Report Inappropriate Content
тАО12-06-2006 03:50 AM
тАО12-06-2006 03:50 AM
Re: Network card info required
what you would like most is possibly this:
$ ANAL/SYS
SDA> CLUE FRU
FRU Table written to CLUE$FRU.SYS file, use System Event Analyzer or Error Log V
iewer to analyze.
SDA> EXIT
$ DIAGNOSE CLUE$FRU.SYS
this will show you the 'System Init Log', which is more-or-less the system console output from the last INIT.
Volker.
PS: This needs DECevent to be installed. You can also try this with WEBES/SEA.
- Mark as New
- Bookmark
- Subscribe
- Mute
- Subscribe to RSS Feed
- Permalink
- Report Inappropriate Content
тАО12-06-2006 05:17 AM
тАО12-06-2006 05:17 AM
Re: Network card info required
What I would want to determine first is whether the node crashed because the driver threw a wobbly, or because setting it to full duplex was a really bad idea.
Do the LANCP counters look OK running at half-duplex? An awful lot of people cause themselves a world of pain by setting their systems to full duplex when the network equipment is set to autonegotiate.
- Mark as New
- Bookmark
- Subscribe
- Mute
- Subscribe to RSS Feed
- Permalink
- Report Inappropriate Content
тАО12-06-2006 06:45 PM
тАО12-06-2006 06:45 PM
Re: Network card info required
This is new to me. I would advise everyone to try it too.
The diag then gives you : some important env variables, firmware versions and a lot of device info. I can see the device types of the ethernet card but not the speed it can handle.
Wim
- Mark as New
- Bookmark
- Subscribe
- Mute
- Subscribe to RSS Feed
- Permalink
- Report Inappropriate Content
тАО12-06-2006 07:24 PM
тАО12-06-2006 07:24 PM
Re: Network card info required
running OpenVMS V7.3-2:
SDA> clue fru
FRU Table not available or not implemented.
That was fun.
- Mark as New
- Bookmark
- Subscribe
- Mute
- Subscribe to RSS Feed
- Permalink
- Report Inappropriate Content
тАО12-06-2006 07:32 PM
тАО12-06-2006 07:32 PM
Re: Network card info required
Have used the info and found the what I need.
We don't have DecEvent installed but it is in the pipeline.
Regards Terry.
- Mark as New
- Bookmark
- Subscribe
- Mute
- Subscribe to RSS Feed
- Permalink
- Report Inappropriate Content
тАО12-07-2006 04:20 AM
тАО12-07-2006 04:20 AM
Re: Network card info required
- Mark as New
- Bookmark
- Subscribe
- Mute
- Subscribe to RSS Feed
- Permalink
- Report Inappropriate Content
тАО12-07-2006 04:20 AM
тАО12-07-2006 04:20 AM