- Community Home
- >
- Servers and Operating Systems
- >
- Operating Systems
- >
- Operating System - OpenVMS
- >
- Re: Printing Problem from One Cluster Node
Categories
Company
Local Language
Forums
Discussions
Forums
- Data Protection and Retention
- Entry Storage Systems
- Legacy
- Midrange and Enterprise Storage
- Storage Networking
- HPE Nimble Storage
Discussions
Discussions
Discussions
Forums
Forums
Discussions
Discussion Boards
Discussion Boards
Discussion Boards
Discussion Boards
- BladeSystem Infrastructure and Application Solutions
- Appliance Servers
- Alpha Servers
- BackOffice Products
- Internet Products
- HPE 9000 and HPE e3000 Servers
- Networking
- Netservers
- Secure OS Software for Linux
- Server Management (Insight Manager 7)
- Windows Server 2003
- Operating System - Tru64 Unix
- ProLiant Deployment and Provisioning
- Linux-Based Community / Regional
- Microsoft System Center Integration
Discussion Boards
Discussion Boards
Discussion Boards
Discussion Boards
Discussion Boards
Discussion Boards
Discussion Boards
Discussion Boards
Discussion Boards
Discussion Boards
Discussion Boards
Discussion Boards
Discussion Boards
Discussion Boards
Discussion Boards
Discussion Boards
Discussion Boards
Discussion Boards
Discussion Boards
Discussion Boards
Discussion Boards
Discussion Boards
Community
Resources
Forums
Blogs
- Subscribe to RSS Feed
- Mark Topic as New
- Mark Topic as Read
- Float this Topic for Current User
- Bookmark
- Subscribe
- Printer Friendly Page
- Mark as New
- Bookmark
- Subscribe
- Mute
- Subscribe to RSS Feed
- Permalink
- Report Inappropriate Content
тАО03-29-2006 07:59 PM
тАО03-29-2006 07:59 PM
I have a printing problem appeared when I print the same job from one node of two nodes cluster. I have got a correct printout from node-B while I have a shifting (uncorrectable printout)when I print multi pages through the same job from node-A.
The cluster configuration done as one system disk and the same queue manager plus the same sysuaf.dat file.
(This is a new cluster system migrated from an old single system after buying new Servers and we did this migration due to a retired software installed and running).
The only differece between two nodes is the sysgen parameters.So are there any system parameter affects on this issue??!!
Please advise . . .
Regards,
Emad Omar
Solved! Go to Solution.
- Mark as New
- Bookmark
- Subscribe
- Mute
- Subscribe to RSS Feed
- Permalink
- Report Inappropriate Content
тАО03-29-2006 08:16 PM
тАО03-29-2006 08:16 PM
Re: Printing Problem from One Cluster Node
and see if all files are in sys$common (esp. form libraries).
Else : what kind of printing (lpd, lat, dcps, ...), versions ?
Wim
- Mark as New
- Bookmark
- Subscribe
- Mute
- Subscribe to RSS Feed
- Permalink
- Report Inappropriate Content
тАО03-29-2006 08:25 PM
тАО03-29-2006 08:25 PM
Re: Printing Problem from One Cluster Node
before answering lots of questions, could you provide a 'SHOW QUE/FULL/ALL printer-queue-name' from both nodes ?
Volker.
- Mark as New
- Bookmark
- Subscribe
- Mute
- Subscribe to RSS Feed
- Permalink
- Report Inappropriate Content
тАО03-29-2006 08:53 PM
тАО03-29-2006 08:53 PM
Re: Printing Problem from One Cluster Node
Thank you for your fast reply.
regarding the $show queue/all/full I need to tell you that each nodes have the same definition, because we start and intilized the queue using the same script on sys$common.
On other hand we are using LAT Protocol and for this job we are using the following command :
$print/device=ltaxxxx filename
Kind regards,
Emad
- Mark as New
- Bookmark
- Subscribe
- Mute
- Subscribe to RSS Feed
- Permalink
- Report Inappropriate Content
тАО03-29-2006 09:07 PM
тАО03-29-2006 09:07 PM
Re: Printing Problem from One Cluster Node
since you say the pages are shifted, can you check and compare the terminalsettings of your LTA devices ( SHOW TERM LTAxx)?regards Kalle
- Mark as New
- Bookmark
- Subscribe
- Mute
- Subscribe to RSS Feed
- Permalink
- Report Inappropriate Content
тАО03-29-2006 09:46 PM
тАО03-29-2006 09:46 PM
Re: Printing Problem from One Cluster Node
Wim
- Mark as New
- Bookmark
- Subscribe
- Mute
- Subscribe to RSS Feed
- Permalink
- Report Inappropriate Content
тАО03-29-2006 10:15 PM
тАО03-29-2006 10:15 PM
Re: Printing Problem from One Cluster Node
by not providing detailled information, you only lead people to ask speculative questions. If Wim could have seen the SHOW QUE/FULL/ALL queue-name output, his questions about setup libraries would have been unnecessary, if that queue does not even use them...
Please also try to explain, how the print output differs if printed on node node or the other.
Volker.
- Mark as New
- Bookmark
- Subscribe
- Mute
- Subscribe to RSS Feed
- Permalink
- Report Inappropriate Content
тАО03-30-2006 01:17 PM
тАО03-30-2006 01:17 PM
Re: Printing Problem from One Cluster Node
Start with TT_DEFCHAR and TT_DEFCHAR2
Phil
ps
HELP PRINT /DEVICE on my system
says that /DEVICE is synonymous with /QUEUE
and its use is not recommended
What happens on each node if you
$copy
- Mark as New
- Bookmark
- Subscribe
- Mute
- Subscribe to RSS Feed
- Permalink
- Report Inappropriate Content
тАО03-30-2006 05:19 PM
тАО03-30-2006 05:19 PM
Re: Printing Problem from One Cluster Node
The lta device will show as allocated on the node where its queue is started.
I assume this is node-B in your case, and print/device from node-A is the problem?
Phil
- Mark as New
- Bookmark
- Subscribe
- Mute
- Subscribe to RSS Feed
- Permalink
- Report Inappropriate Content
тАО04-02-2006 05:29 PM
тАО04-02-2006 05:29 PM
Re: Printing Problem from One Cluster Node
I'm Emads colleague and I will continue this Issue with all, Today I'll try all what you asked.
Please be patient.
Mahmoud.